Bedienungsanleitung Thomson ROC6306 6in1 (Seite 2 von 3) (Englisch)

607839

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

Method B – 4-digit codes Programming

Before you start programming, you must find the code of

the set to be controlled.

Refer to the list provided with these instructions, page II

of the codes.

1. S witch on the set you want to control.

2. Hold down the S (10) until the red indicator

lamp (1) remains lit (the indicator light remains on

for a few seconds to give you the time to proceed with

the following steps. The indicator lamp flashes when

this time is almost up, and then goes off).

3. P ress the key (3) that corresponds to the type of

equipment you want to control:

TV: television set,

DVD: DVD player,

VCR: video cassette recorder,

DVB-T: DVBT receiver,

SAT: satellite,

AUX: other devices.

4. W hile the indicator is lit, enter the first digit of the

4-digit code proposed for the set to be controlled

(example: 0036 for Thomson). The red indicator then

goes off if the code is correct or flashes, if the code is

not on the list.

5. D irect the remote control towards the set and try to

switch it off by pressing the B (2) key.

6. S hould the set not switch off, repeat step 2. Then type

in the next 4-digit code. Tr y to switch off the set by

pressing

(2) key once. Repeat this procedure by

trying out each of the 4-digit codes.

Check of the programming:

In principle, your set is ready for receiving the remote control

commands.Check your remote control for proper functioning by

performing the test described on page 3.

Method C – Programming by means of

code retriever

Should none of the codes work, you still have the possibility

of retrieving the appropriate code without having to perform

any input.

1. S witch on the set you want to control.

2. Hold down the S (10) until the red indicator

lamp (1) remains lit (the indicator light remains on

for a few seconds to give you the time to proceed with

the following steps. The indicator lamp flashes when

this time is almost up, and then goes off).

3. P ress the key (3) that corresponds to the type of

equipment you want to control:

TV: television set,

DVD: DVD player,

VCR: video cassette recorder,

DVB-T: DVBT receiver,

SAT: satellite,

AUX: other devices.

4. D irect the remote control towards the set and try to

switch it off by pressing the B (2) key.

5. I f the set you want to control switches off, press

c (14) to memorise the subcode.

6. S hould the set not switch off, press

(2) key, as

many times as required (up to 200 times), until the set

switches off. Wait approximately one second between

key presses to give the red indicator lamp (1) enough

time to go off and light up again. Proceeding this way

will enable you to see whether the set responds or

not.

7. Immediately upon the switching-off of the set to be

controlled, press c (14) to store the subcode.

Note:

If you want to assign another type of product than those

mentioned on the remote control, begin by entering a code that

corresponds to the product you want to programme (a 4-digit

code that you will find in the code booklet – see method B).

Example: if you want to control a satellite receiver with the

DVD key, begin by entering a satellite code (any satellite, for

example: 0603 for a Thomson satellite receiver) then begin

the procedure.

Check of the programming:

In principle, your set is ready for receiving the remote control

commands.Check your remote control for proper functioning by

performing the test described on page 3.

Method D - Automatic code search

With this method, the remote control scrolls through the full

code list by sending an IR signal to the set to be controlled

remotely. Proceed as follows:

1. C heck that your equipment is on. If not, switch it on

manually.

2. Hold down the S (10) until the red indicator

lamp (1) remains lit (the indicator light remains on

for a few seconds to give you the time to proceed with

the following steps. The indicator lamp flashes when

this time is almost up, and then goes off).

3. Release the S (10) key.

4. P ress the key corresponding to the type of equipment

(for example TV).

5. P ress the PROG+ (15) key once. After a few seconds

the remote control begins to list all the codes included

in the library (around 1 code per second). Press

PROG+ (15) a second time to reduce the speed

of the test (1 code every 3 seconds). As soon as the

device changes channel you must immediately press

c (14) to record the code and stop the listing. If

you have gone past the code, you can go back to the

previous code by pressing PROG- (15) as many

times as necessary (you can go forward by pressing

(2) or PROG+ (15). As soon as the device reacts

again, press c (14) to record the code.

Note:

If you want to assign another type of product than those

mentioned on the remote control, begin by entering a code that

corresponds to the product you want to programme (a 4-digit

code that you will find in the code booklet – see method B).

Example: if you want to control a satellite receiver with the

DVD key, begin by entering a satellite code (any satellite, for

example: 0603 for a Thomson satellite receiver) then begin

the procedure.

Method E – Programming for control of a COMBO

(combined TV-VCR, TV/DVD, VCR/DVD, ... set)

Depending on the COMBO group (TV/VCR, V CR/DVD, etc.) and

the make, you will be required to enter a single code for both

devices in the COMBO, or to enter two codes, one code per

device. Consult the separate list to discover this. Before you start

programming, you must find the subcode or code of the

subset to be controlled (television or video recorder).

Refer to the list supplied with this user manual (see page

subcodes or codes).

01_ROC6306_GB.indd 2 8/12/06 9:51:10

Thomson ROC6306 6in1 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Thomson ROC6306 6in1

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info