699585
20
Zoom out
Zoom in
Vorherige Seite
1/22
Nächste Seite
16
Problem Possible cause What to do
No sound on TV or
amplier.
The volume of the TV is set too
low.
The volume of the receiver is set
too low.
Increase the volume of the TV with
its remote control.
Increase the volume of the receiver
with its remote control.
The correct input is not selected
on your TV or amplier, or the unit
is set to a higher resolution than
supported by the TV.
Switch to the correct TV/amplier
input.
Select lower resolution on the
receiver.
The TV, digital receiver or amplier
is not switched on.
Switch the TV/digital receiver/
amplier on.
The TV or digital receiver is not
connected to the mains.
Check the mains lead.
Bad cable connection.
Make sure that any existing digital
or analogue A/V cable connections
between the used equipment (TV,
digital receiver or A/V amplier)
are properly connected.
Audio is muted.
Press the ! button on your
remote control.
The TV power is off. Turn the TV on.
No access to scrambled
services.
The channel is scrambled.
Your receiver doesn't support
scrambled channels.
Select an alternative channel.
No response to the
remote control.
The receiver is off. Plug in and turn on the receiver.
The remote control is not aimed
correctly.
Aim the remote control at the IR
sensor on the front panel of the
receiver.
The IR sensor on the front panel of
the receiver is obstructed.
Avoid or remove obstructions.
The batteries of the remote
control are not inserted, wrongly
inserted or exhausted.
Check whether the batteries are
inserted correctly or exhausted. If
exhausted, replace the batteries in
the remote control.
After moving the
DVB-T2 Receiver to
another room/area you
are no longer able to
receive digital reception.
The antenna signals are too weak.
Press INFO on the remote control
to keep the signal bars on screen
and adjust the Indoor antenna for
maximum reception. Alternatively,
do a rescan of the channels.
The signal strength/quality might
be less than before, if using an
indoor antenna.
When using an active antenna,
check if the antenna power setting
is On.
Try using an outdoor antenna.
The receiver switches
off or to standby
automatically.
The Auto Standby function is
enabled and has reached the set
time.
Disable Auto Standby. Refer to the
user manual of your receiver for
details.
20

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Thomson THT709 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Thomson THT709

Thomson THT709 Bedienungsanleitung - Französisch - 23 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info