Bedienungsanleitung Thorma Alicante (Seite 1 von 30) (Deutsch, Englisch)

745831

Zoom out

Zoom in

Vorherige Seite

1/30

Nächste Seite

ALICANTE, VALENCIA, ALMERIA

Installation and operation manual solid fuel fireplace insert

GB ALICANTE, VALENCIA, ALMERIA

tested according to the standard EN 13229

1. Installation manual

1.1 General

Fireplace insert for solid fuel is a single-shaft heating device which replaces the existing heating for short periods between seasons or

supports it in the cold seasons. Fireplace insert is designed for local heating. Fireplace insert can be installed in a normal environment.

This fireplace insert has been tested according the standard EN 13229 with fuels: wood and brown-coal briquettes. This fireplace insert

met the requirements of this standard.

All local regulations, including regulations relating to national and European standards have to be followed when installing the fireplace

insert.

Before mounting the fireplace insert, you have to inform the competent master chimney sweep who will inspect as expert the proper

connection of fireplace insert to the chimney. Fireplace insert must be installed on floorings that have corresponding loading capacity. By

installation, it is necessary to ensure sufficient space for cleaning of fire insert, flue and chimney. The fire insert must be closed during

operation, but also when not in operation, because otherwise it might significantly affect other devices connected to the chimney.

Combustion chamber is enclosed by sheet metal plate filled from inside with vermiculittes. In the bottom part of the combustion chamber,

there is the bed with cast-iron grate. There is an ash box under the grate. Stokers door are sealed with gasket. The door may be opened

only to add fuel. The stokers door are paned with highly heat-resistant glass-ceramic.

The smallest size of the front opening in the lining of fireplace insert is: width 600 mm and height 750 mm. Surface temperatures of the

lining can reach, depending on thermal resistance coefficient of the used construction material and its thickness, within the range between

30 and 80°C.

NOTE: when claiming or ordering spare parts always quote the name, type and serial number given on the data card.

1.2 Specifications

Nominal capacity:

8,0 kW

Nominal heating capacity efficiency:

wood = 82,3 %, lignite briquettes = 70,5 %

Operating chimney draft:

10 Pa

Height with legs

825 mm

Width

ALICANTE=588 mm, VALENCIA=590 mm, ALMERIA=600 mm

Depth

ALICANTE=392 mm, VALENCIA=423 mm, ALMERIA=385 mm

Draught shaft diameter:

Ø150 mm

Weight

ALICANTE=61 kg, VALENCIA=75 kg, ALMERIA=71 kg

Recommended fuel:

- dry hard wood: approximate heating value 15 MJ.kg

-1

- lignite briquettes: approximate heating capacity 20 ÷ 23 MJkg

-1

Approximate consumption of recommended fuel at nominal capacity:

- wood: 2.2 kg.hod.

-1

- lignite briquettes: 1.7 kg.hod.

-1

Heating capacity:

- favourable type of construction: 190 m³

- less favourable type of construction: 145 m³

- unfavourable type of construction: 98 m³

Applicable standards: EN 13229

1.3 Connection to the chimney

At installation comply with all corresponding project, safety and hygienic regulations.

Data to calculate the chimney (at the nominal thermal power):

Fuel

Brown-coal briquettes

Wood

Flue gas flow [g/s]

10,0

6,1

Max. flue gas temperature behind exhaust throat [°C]

377

312

Min. blast draught at nominal thermal power [Pa]

The fireplace insert can be used to connect a multi-occupied chimney, which means that to the chimney with the fire insert connected,

we can connect more devices.

Before connecting the fireplace insert, make sure there is sufficient blast in the chimney. Flame of a burning paper or candle should be

sucked into the chimney opening. The fireplace insert should be attached to the chimney flue in the shortest direction.

The fireplace insert should be attached to the chimney flue always with the consent of competent chimney sweeper office in compliance

with STN 73 4210 and STN 73 4201.

If the fireplace insert cannot be attached to the chimney flue directly, the flue involved should be the shortest possible and ascend towards

the chimney. Flues can be of maximum 1,5 m length. In any case, it is necessary to ensure smoke tubes and bends, mounted on exhaust

throat, against getting loose by a pin. Smoke tubes and bends must be attached firm and tight to the fireplace insert and plugged into

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Thorma Alicante Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info