Do not wear loose clothing or jewelry, as they can get caught in moving parts. Non-skid footwear is recommended when working
outdoors. Wear protective hair covering to contain long hair.
7. Use safety gear
Use safety glasses, safety footwear, snug fitting clothing, protective gloves, and protective hearing and head gear.
8. Carrying the saw
Carry the saw by the front handle with the saw stopped. Keep your finger off the switch, and make sure that the guide bar and saw chain
are to the rear.
9. Do not abuse the cord
Never carry the tool by the cord or yank it to disconnect it from the socket. Keep the cord away from heat, oil and sharp edges.
10. Secure work
Use clamps or a vice to hold the work.
11. Do not overreach
Keep proper footing and balance at all times.
12. Maintain the chain saw with care
Inspect the chain saw cords periodically and, if damaged, have them repaired by an authorized service facility. Keep the cord clear of
the chain and operator at all times. Never carry the saw by the cord or pull it to disconnect from receptacle. Keep the cord from oil and
sharp edges. Inspect the extension cords periodically and replace if damaged. Keep tools sharp and clean for better and safer
performance. Follow instructions for lubricating and changing accessories. Keep handles dry, clean and free from oil and grease.
13. Disconnect the chain saw
Disconnect the chain saw when not in use, before servicing, and when changing accessories and attachments such as saw chain and
guard.
14. Remove adjusting keys and wrenches
Form the habit of checking to see that keys and adjusting wrenches are removed from the tool before turning it on.
15. Avoid unintentional starting
Do not carry a plugged-in tool with a finger on the switch. Ensure switch is off when plugging in.
16. Use outdoor extension leads
Use only extension cords that are intended for outdoor use and which are so marked (≥ 1,5 mm2).
17. Stay alert
Watch what you are doing. Use common sense. Do not operate the chain saw when you are tired. Keep all parts of your body away from
the saw chain when the motor is operating. Before you start the saw, make sure the saw chain is not contacting anything.
18. Check damaged parts
Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly
and perform its intended function. Check for alignment of moving parts, free running of moving parts, breakage of parts, mounting and
any other conditions that may affect its operation. A guard or other parts that is damaged should be properly repaired or replaced by an
authorized service center unless otherwise indicated in this instruction manual. Have effective switches replaced by an authorized
service facility. Do not use the tool if the switch does not turn it on and off.
19. Warning!
The use of any accessory or attachment, other than those recommended in this instruction manual, may present a risk of personal
injury.
20. Have your tool repaired by a qualified person
This electric tool is in accordance with the relevant safety requirements. Repairs should only be carried out by qualified persons using
original spare parts, otherwise this may result in considerable danger to the user.
Warning! Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches
the saw chain in the cut. Tip contact in some cases may cause a lightning-fast reverse action, kicking the guide bar rapidly back
towards the operator. Pinching the saw chain along the top of the guide bar may push the guide bar rapidly back towards the
operator. Either of these reactions may cause you to lose control of the saw, which could result in serious injury to the user. The
following precautions should be followed to minimize kickback.
21. Guard against Kickback
A. Grip saw firmly! Hold the chain saw firmly with both hands when the motor is running. Keep a good firm grip on the saw with both
hands, the right hand on the rear handle, and the left hand on the front handle.
B. Do not over reach.
C. Keep proper footing and balance at all times.
D. Do not let the nose of the guide bar contact a log, branch, ground or other obstruction.
E. Do not cut above shoulder height.
F. Use devices, such as low-kickback chain, guide bar nose guards, chain brakes and special guide bars, which reduce the risks
associated with kickback.
G. Use only replacement bars and chains specified by the manufacturer or the equivalent.
H. There are no other replacement components for achieving kickback protection in accordance with CSA Z62.3.
22. Power supply
Connect the chain saw to correct voltage; be sure that the voltage supplied is the same as that specified on the nameplate of the tool.
23. Do not operate a chain saw that is damaged, improperly adjusted, or not completely and securely assembled. Be sure that the saw
chain stops moving when the trigger is released.
24. Do not attempt operations beyond your capacity or experience.
25. Do not operate a chain saw with one hand! Serious injury to the operator, helpers, or bystanders may result from one-handed operation.
A chain saw is intended for two-handed use.
26. To reduce potential for electric shock, do not operate the saw on wet or slippery surfaces, or during snow storms, rain storms, and
other adverse weather conditions.
27. Keep the handles dry, clean, and free of oil or grease.
Toledo 05
UK
Под нашу исключительную ответственность удостоверяем, что данное изделие удовлетворяет следующим стандартам и
нормативным документам
EN 50144-1,EN 50144-2-13,EN55014-1,EN55014-2,EN 61000-3-2,EN 61000-3-3
согласно следующим предписаниям:
98/37 EEC,73/23 EEC,89/336 EEC
01-09-2005
ZWOLLE NL
В. Капмхоф
Отдел контроля качества
Постоянное улучшение нашей продукции является нашей политикой и, поэтому, мы оставляем за собой право на изменение
технических характеристик продукции без предварительного уведомления.
Toledo BV,Lingenstraat 6,8028 PM Zwolle,Нидерланды
CE
ДЕКЛАРАЦИЯ О СООТВЕТСТВИИ
(RU)
120 Toledo
RU
