Bedienungsanleitung Toolland DT 20005 (Seite 13 von 16) (Deutsch, Englisch, Holländisch, Französisch)

771265

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

DT 20005 English

www.toolland.eu 13

SPRAYING CHEMICALS

This sprayer is intended for use with water

based solutions of proprietary insecticides,

fungicides, weed killers and follar feeds.

Always follow the chemical suppliers on-pack

instructions as well as the instructions listed

below.

 Wear protective clothing, goggles, face

mask and gloves.

 Avoid inhaling spray mist.

 Avoid skin contact with chemicals.

 Work in a well ventilated area.

 Take care to protect children, pets and

fish from exposure to chemicals.

 Wash hands thoroughly after use and

especially before eating.

 Wash any contamined clothing.

 Seek medical attention if spray gets in

your eyes or if you develop any

symptoms after spraying.

 Do not spray near food or food

preparation areas. When spraying crops,

pay particular attention to the chemical

manufacturer’s advice on time before

crops can be eaten, etc.

 Do not spray any solvent based material

e.g. white spirit.

 Spray only thin watery solutions, thicker

mixtures will clog the nozzle.

 Powdered chemicals can be sprayed

successfully if they are not completely

soluble and the solution tends to settle,

spraying can still be successful so long as

the mixture continually agitated.

 If the material to be sprayed contains

sediment, strain the liquid into the

sprayer bottle.

 Do not over-pressurize the bottle, or

tamper with the pressure release valve.

 After use pay particular attention to the

paragraph on cleaning.

 Your sprayer is manufactured from many

different types of plastic material, and

although the liquid you wish to use may

be packed in a plastic container, this is no

guarantee that it will not damage the

sprayer. If you are in any doubt about

any chemical you intend to spray we

recommend that you contact the

consumer service department at the

address given the check its suitability.

MAINTENANCE

Pressure release valve

 The safety valve is designed to release

any excess pressure and to let you

release the pressure after spraying.

 Do not interfere with the setting of the air

pressure safety valve.

Plunger head

 The O-Ring should be kept lubricated to

slide freely in the barrel and so pump air

efficiently.

 To apply grease proceeds as follows.

 Remove the pumps assembly by

unscrewing in an anti-clockwise direction.

 Locate the pump handle into the carrying

position and grip the barrel.

 Unscrew the plunger retaining cap from

the pump barrel by rotating the handle.

 Withdraw the plunger and apply silicone

grease to the O-Ring.

 When re-assembling ensure the O-Ring is

not trapped between the outer edge of

the plunger moulding and the inside of

the pump barrel.

Pump non-return valve:

(Situated at the bottom of the pump barrel)

 This stops the compressed air in the

container from escaping back into the

pump.

 If it is faulty, the unlocked pump handle

will rise when the container is

pressurized.

 To remove the valve, lift the edge of the

valve and pull. (take care not to damage

the sealing face of the barrel).

 To replace place the valve over the centre

hole and push down firmly.

Pump barrel sealing rings

 These make an air tight seal between

both the pump barrel and adapter.

 Also between the adapter and container

when both are screwed down tight.

 To check this, turn the pressurized

sprayer upside down and if there is a

leak, liquid will be forced from the joints.

Nozzle cap

 Keep this clean and free from obstruction.

 Also, the two swirl grooves at the end of

the lance must be kept clean and free

from sediment to ensure a good spray

pattern.

 The nozzle O-Ring should be kept

lubricated with silicone grease.

Lance

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolland DT 20005 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info