Bedienungsanleitung Toolland FT 92 (Seite 19 von 22) (Deutsch, Englisch, Holländisch, Französisch, Portugiesisch, Spanisch)

622632

Zoom out

Zoom in

Vorherige Seite

1/22

Nächste Seite

FT 92 English

www.toolland.eu 19

4. DETECT GAS LEAKS

 To find the gas leak you must brush

soapy water on all the fittings and

connections of the gas circuit. If there is

a leak you will notice bubbles.

 If you notice bubbles you must close the

leak.

 If there is still a leak after you closed the

leak you must close the gas cylinder

valve and request professional

assistance.

 Only check for leaks when the appliance

has cooled down completely.

 WARNING! Never use a flame to detect a

gas leak!

5. USE

5.1 PREPARATIONS

 Check the appliance for possible transport

damage. Never use a damaged appliance.

 Follow all the instructions carefully.

 Never place the gas cylinder in front of

the heater. Place the gas cylinder and the

appliance on a stable and level surface.

 Always check if the specifications of the

regulator and the hose are the same as

the specifications mentioned on the rating

label.

 Take the cabinet on the rear cylinder

cover unscrew of the two fixing screw.

 The heater must be used with a regulator

and hose. The flexible hose must be

checked regularly whenever the cylinder

is replaced to be sure it has no scratches

or cuts and that it is in a perfect state. It

must be replaced in any case before the

expiry date stamped on the hose itself.

 Connect the flexible tube to the hose

union of the pressure regulator and to

that of the tap, making sure that the

metal bands are tight and paying

particular attention not to tamper with or

damage any component or fitting.

 Before connecting the cylinder, make sure

that its tap is closed and that there are

no open flames (lit oven, etc.) in the

place where you are working. Screw the

pressure regulator onto the cylinder,

keeping these warnings in mind:

 Check that the gasket seal is in

good condition.

 Attach the regulator to the tap,

screwing the nut tightly

counterclockwise.

 Carefully check that there is no

gas leaking from the connection

using soapy water: if there is a

leak, bubbles will form; tighten

the connection more or seek

professionally qualified service.

 Place the cylinder in its compartment,

taking care that the tube is not twisted or

choked and isn't touching hot parts.

 Hook the rear cylinder cover on the

cabinet, insert the two hooks in the

respective holes of the cabinet and put

the wing screws.

 To replace the cylinder, make sure that its

tap is closed and that there are no open

flames (lit oven, etc.) or sources of heat

in the place where you are working; we

recommend that you check that the

gasket seals of the regulator and flexible

rubber tube are in good condition and

replace them, if necessary.

 To not mishandle the connections or

other components.

 Do not turn the cylinder upside down to

completely use its contents: this releases

liquid residues left in the tank that will

irreparably damage the heater.

 Do not disconnect the pressure regulator

from the cylinder when the cylinder tap is

open.

 The manufacturer will not be responsible

if one of the above points is disregarded.

5.2 START AND STOP

Pos. 1 (Start and Maximum Heating)

Pos. 2 (Medium)

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Toolland FT 92 Seite 19

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info