465047
17
Zoom out
Zoom in
Vorherige Seite
1/84
Nächste Seite
17
EN
Introduction Connections Playback Editing OthersFunction SetupRecording VHS Functions
Basic Setup /
TV View Operation
Connecting to a TV
Connect the unit to a TV after considering the capabilities of
your existing equipment.
Connect the antenna or cable to the ANTENNA
IN jack of this unit.
Connect the ANTENNA OUT jack of this unit to
the Aerial jack of your TV.
Connect AV1 (TV) Scart socket of this unit to
the Scart socket of your TV.
Note
If your TV does not have a Scart socket, use a Scart/RCA
cable to connect.
Connect this unit directly to the TV. If the AV cables are
connected to a VCR, pictures may be distorted due to the
copy protection system.
Analogue teletext can only be output in VCR mode through
AV1 (TV) out. Use TV remote control to decode the
analogue teletext.
When changing the “Video Out” setting (“SCART (RGB)”,
“Component (Interlace)” or “Component (Progressive)”),
connect to the corresponding jack on the TV. If the setting is
changed, for example, to “Component (Interlace)” or
“Component (Progressive)” while the scart cable is
connected to the TV, a distorted video signal may be output.
If your TV has component video input jacks, use a component
video cable and an audio cable (to connect the AUDIO OUT
(L\R) jacks).
When using this type of connection, “Video Out” setting
should be set to “Component (Progressive)” or “Component
(Interlace)”. Refer to “Video Out” on page 71.
Component connection provides the better quality picture.
Connect the COMPONENT VIDEO OUT jacks of
this unit to the component video input jacks of
your TV.
Connect the AUDIO OUT (L\R) jacks of this unit
to the analogue audio input jacks of your TV.
After you have made the connections, set the “Video Out”
setting. (See page 71.)
Selecting Progressive Scan (576p/480p or
Interlaced 576i/480i) Playback
If your TV is compatible with progressive scanning (576p/
480p), connect the TV to the COMPONENT VIDEO OUT
jacks of this unit and set “Video Out” setting to “Component
(Progressive)” in “Setup” menu. (See page 71.) Next, set
your TV to the progressive scan mode.
If your TV is not compatible with progressive scan, set
“Video Out” setting to “Component (Interlace)”.
Use a commercially available adaptor if the video input jacks
of your TVs or monitors are the BNC type.
Only component and HDMI connections are compatible with
the Progressive Scan.
Connections
Before installation, unplug your TV and
this unit.
Using the Scart socket
1
2
RF cable
(not supplied)
RF cable
(supplied)
Cable
Signal
or
To A er ia l j ack
Antenna
1
2
Scart cable
(not supplied)
Scart/RCA cable (not supplied)
Audio/video cable
(not supplied)
Scart adaptor
(not supplied)
Using the COMPONENT VIDEO OUT
Jacks and the AUDIO OUT (L\R) Jacks
YPB/CB PR/CR
1
2
Audio IN
Component
video IN
Audio cable
(not supplied)
Component
video cable
(not supplied)
1
2
E3TK2BD_EN.book Page 17 Thursday, April 16, 2009 12:00 PM
17

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Toshiba RDXV59 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info