Bedienungsanleitung TP-LINK TD-W8950N (Seite 2 von 2) (Englisch)

664645

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

FAQ (Frequently Asked Questions)

Q1. What can I do if the login page does not appear?

A1. Make sure the computer is connected to the modem router properly.

A2. If the computer is set to a static or ﬁxed IP address, change it to obtain an IP address

automatically from the modem router.

A3. Verify http://tplinkmodem.net is correctly entered in the web browser and press Enter.

A4. Use another web browser and try again.

A5. Reboot your modem router and try again.

A6. Disable and enable the active network adapter.

Q2. What can I do if I cannot access the Internet?

A1. Make sure the telephone and Ethernet cables are plugged in correctly.

A2. Try to log into the web management page of the modem router using the default

address at http://tplinkmodem.net. If you can, try the following answers. If you cannot,

change your computer to obtain an IP address automatically from the modem router.

A3. Consult your ISP and make sure all the VPI/VCI, WAN Link Type, account username and

password are correct. If they are not, please replace them with the correct settings and

try again.

A4. Restore the modem router to its factory default settings and reconfigure the modem

router by following the instructions in this Quick Installation Guide.

A5. Please contact our Technical Support if the problem still exists.

Q3. How do I restore the modem router to its factory default settings?

Q5. What can I do if the ADSL LED does not turn solid on?

A1. Check your cables and make sure they are all plugged in correctly, including the

telephone lines and power adapter.

A2. Manually change your DSL settings. Log into the modem router’s web management

page. Go to Advanced Setup > DSL, untick all the modulation options except G.dmt

Enabled, ADSL 2 Enabled and AnnexL Enabled and click Save/Apply.

A3. Restore your modem router to its factory default settings by referring to FAQ > Q3.

A4. Remove the ADSL splitter, directly connect the modem router to the phone jack and

then reconfigure the modem router by following the instructions in this Quick

Installation Guide.

A5. Contact your Internet service provider to verify if the ADSL line is in good status.

A6. Please contact our Technical Support if the problem still exists.

Q4. What can I do if I forget my password?

Web Management page password:

Refer to FAQ > Q3 to reset the modem router, and then use admin (all lowercase) for both

username and password to log in.

Wireless Network password:

A1. The default Wireless Password/PIN is printed on the product label of the modem router.

A2. If the default wireless password has been changed, log into the modem router's web

management page and go to Wireless > Security to retrieve or reset your wireless

network password (also called WPA/WAPI passphrase).

A1. With the modem router powered on, press

and hold down the WPS/RESET button on the

rear panel of the modem router for more than

5 seconds and then release it. If all LEDs turn

on momentarily, you restore the modem

router successfully.

WPS/RESET Button

Press & Hold for more than 5 seconds

Configuring the Modem Router

Wireless

a. Find the SSID (network name) and

Wireless Password printed on the

product label at the bottom of the

modem router.

1. Connecting your computer to the modem router (Wired

or Wireless).

Wired

Ethernet cable

A2. Log into the web management page of the

modem router, and go to Management >

Settings > Restore Default, click Restore

Default Settings and wait until the reset

process is complete.

Notes:

1) All the Internet settings in the figure below are used for demonstration only. If you are unsure of the

Internet settings, please contact your ISP.

2) Per FCC regulations, all Wi-Fi products marketed in the U.S. must be fixed to the U.S. region only.

Verify or change the Wireless settings (wireless network settings) and click Next to

continue.

Check all the parameters and click Confirm to complete the configuration.

Note: You may personalize your wireless network name and key. Once done, you will have to reconnect to

your Wi-Fi network using the new wireless network name and key.

Quick Setup - WAN Configurations

OtherCountry:

ISP: Other

WAN Link Type:

PPPoE

35VPI/VCI: 8 ([0~255] / [32~65535])

XXXXXXXXXXX

PPP Username:

*************

PPP Password:

Encapsulation Mode:

LLC/SNAP-BRIDGING

(optional)

1480

MTU (bytes):

(optional)

PPPoE Service Name:

(optional)

Back Skip WAN

Quick Setup - Wireless Configurations

TP-LINK_XXXXWireless Network Name :

Network Authentication:

WPA2-Personal

Wireless Network Key : ********

Enable Wireless:

Back Skip Wi-Fi

(Also called SSID)

Click Quick Setup from the menu and click Next to continue, then select ADSL WAN

and click Next.

C Select your Country and ISP from the drop-down list. Complete the WAN settings

with the information provided by your ISP and click Next. Here we use PPPoE for

demonstration.

Quick Setup - WAN Configurations

Skip WAN

Choose WAN Type:

For ADSL(Telephone line/RJ11) Service

For Ethernet(RJ45) ServiceEthernet WAN

ADSL WAN

Enable IPv6 for this service

2. Configuring the modem router via a web browser.

Please consult your ISP (Internet Service Provider) for the following information

before configuring the modem router.

VPI and VCI: _______ WAN Link Type: _______

Encapsulation Mode (optional): _____________

If your WAN Link Type is PPPoE/PPPoA, please get further information of your

account username and password.

Enter http://tplinkmodem.net or 192.168.1.1 in the address bar of a web

browser. Use admin for both username and password, and then click Login.

Note: If the login window does not appear, please refer to FAQ > Q1.

http://tplinkmodem.net

admin

POWER

ON/OFF

WiFi

WPS/

RESET

LAN4

LAN1LAN3 LAN2

ADSL

b. Click the network icon of your computer or go to Wi-Fi Setting of your smart

device, then select the SSID to join the network.

7106506218 REV6.0.2

Connect a computer to the modem router and the LAN LED lights up.

Connections are available

Wireless Network Connection

Connect automatically Connect

√

TP-LINK_XXXX

Wi-Fi

TP-LINK_XXXX

CHOOSE A NETWORK...

Other...

Computer

Smart Device

< Settings

TP-LINK TD-W8950N Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von TP-LINK TD-W8950N

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info