Bedienungsanleitung Trebs 99363 (Seite 5 von 9) (Englisch)

732444

Zoom out

Zoom in

Vorherige Seite

1/9

Nächste Seite

3. Please ensure the ice cube maker is placed on a stable table or platform to avoid malfunction.

4. The incline angle of the ice cube maker cabinet should not exceed 45° during transportation or use. Do not

turn the ice cube maker upside down otherwise it could cause the compressor or refrigerating system to

operate incorrectly. Please allow time for the fluids in the compressor to settle after the ice cube maker is

moved or transported. Before using the ice cube maker for the first time, please wait for 2 hours after the

unit has been moved and positioned in the proper place.

5. The ice cube maker must be placed on a dry and flat surface with sufficient ventilation, far from heat sources

such as ovens, heaters and corrosive gases. Leave about 15cm space on all sides of the ice cube maker for

proper ventilation.

6. Do not fill the water reservoir with hot water. This may damage the ice cube maker. It is best to fill the water

reservoir with water of room temperature or lower.

7. Do not use the appliance at a very cold environment (lower than 5℃).

8. Clean the appliance by following the operation of “CLEANING AND MAINTENANCE” before operate.

Using your ice cube maker

1. Ensure that the drain plug at the bottom of the water reservoir is closed well.

2. Plug the ice cube maker into the wall outlet, the “ICE” indicator blinks.

NOTE: please make the ice cube maker be rested for 30 minutes before pluged if it has been moved.

3. Open the top lid and remove the ice basket.

4. Fill the water reservoir with drinking water.

NOTE: do not fill above the MAX water level mark.

5. Replace the ice basket and close the top lid.

6. Press the “ON/OFF” key, and the “ICE”indicator lights solidly.

7. The ice-making cycle will last approximately 7-15 minutes, depending on the ambient temperature and water

temperature.

8. The ice-making cycle starts with water being pumped into the ice tray situated below the evaporator. Over

the next 7-15 minutes ice forms on the evaporator. Once this has completed, the ice tray will tilt backwards

and the remaining water in the ice tray is drained back into the water reservoir. The ice cubes are then

dropped from the evaporator and pushed forward into the ice basket by the ice shovel. The ice tray will

automatically move back into position under the evaporator and start the next cycle.

9. The “ICE FULL” indicator will light up when the ice basket is full and then the ice cube maker will stop the

ice-making cycle automatically. Gently remove the ice from the ice basket with the ice scoop. About 5

seconds later, the ice cube maker will restart its ice making function automatically.

10. The “ADD WATER” indicator will light up when the water reservoir is lack of water and the ice-making cycle

will stop automatically. At that time, remove the ice basket and add water to the water reservoir, and then

press the “ON/OFF” key again to restart the ice-making cycle. The appliance will start working automatically

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trebs 99363 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info