530952
3
Zoom out
Zoom in
Vorherige Seite
1/16
Nächste Seite
Part list
A
B
C
D
E
F
G
H
I
J
K
L
Stirring Vessel
Please insure that the drive shaft is installed properly at the bottom of the mixing cup (F).
The food volume should not exceed the maximum capacity of the mixing cup (F) (approximately
400ml).
The temperature for mixing the food should not higher than 80 degrees.
Do not put your fingers or any thing into the mixing cup (F) when it is connecting to the electricity
supply. Only when the electricity supply is cut off, than you can deal with the food attached to the
wall of the mixing cup.
Do not demolish the mixing cup (F) when it is still at work.
Equipped with safety locks
The product is equipped with a safety lock (L). When the mixing cup (F) is not or inappropriately
installed, the dynamo (B) can not work.
Usage Instructions
Please clean the parts which contact with the food before you use the product for the first time
(see chapter cleaning)
Put the food into the mixing cup (F) under the specified capacity (approximately 400ml).
Put the mixing cup into the safety lock (L), the cup should than rest on the cup holder (J)
Please insure that the plug (H) is connected and the mixing cup (F) is installed properly before
you start the product.
Press the speed control/ on/ off button (I) and start the dynamo (B). Press ‘I’ for fine mixing and
press ‘II’ for the more rough mixing, press ‘0’ for finish mixing.
During the mixing process (not longer than 2 minutes), do not put raw material into the mixing
cup; only after the electricity supply is cut off and the machine stops, can raw material be added
into the mixing cup.
Cleaning
Please use water to clean the parts which contact with the food after using it. Install the
stirring vessel properly(see usage Instruction), detergent warm water into the mixing cup.
Please cut off the power (speed control/ on/off button (I) at ‘0’) before cleaning it.
Generally, dish-washer can not be used to clean the product or the spare parts.
Soft wet cloth can be used to polish the dynamo (B), do not immerse dynamo (B) in water.
Do not use abrasive, brusher or alcohol, etc.
Demolish the mixing cup (F) and rinse it out with clean warm water.
A: Dynamo cover
B: Dynamo
C: Drive shaft
D: Stirrer
E:Stirring rod
F: Mixing cup
G: Base
H: Plug
I: Speed control/ on/off switch
J: Cup holder
K: Holder
L: Safety lock for the cup
3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Tristar BL-4425 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info