Bedienungsanleitung Triton JOF 001 (Seite 6 von 82) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

664978

Zoom out

Zoom in

Vorherige Seite

1/82

Nächste Seite

• Disconnect from the power supply before carrying out any adjustment, servicing or

maintenance

WARNING: Dust generated by using power tools can be toxic. Some materials may be

chemically treated or coated and be a toxic hazard. Some natural and composite materials

may contain toxic chemicals. Some older paints may contain lead and other chemicals. Avoid

prolonged exposure to dust generated from operating a router. DO NOT allow dust to get onto

skin or eyes and do not allow the dust to enter your mouth to prevent absorption of harmful

chemicals. Where possible, work in a well-ventilated area. Use a suitable dust mask and dust

extraction system where possible. Where there is a higher frequency of exposure, it is more

critical that all safety precautions are followed and a higher level of personal protection is used.

Product Familiarisation

1. Speed Controller

2. Motor

3. Power Switch with Lock-Out Cover

4. Handles

5. Collet

6. Dust Extraction Port

7. Plunge Lock Lever

8. Micro Winder

9. Turret Stops

10. Table-Winder Connection Point

11. Depth Stop Lock Knob

12. Safety Guards

13. Baseplate Mounting Knobs

14. Fence

15. Spanner

16. Extended Baseplate

17. Collet

18. Table Height Winder

19. Pivot Mount

20. Brush Caps

Intended Use

Hand-held, mains-powered plunge router used for cutting proﬁles, grooves, edges and

elongated holes in natural and composite wood, and also stationary installation in the Triton

Precision Router Table, the Triton Workcentre, and other suitable table systems.

Unpacking Your Tool

• Carefully unpack and inspect your new plunge router. Familiarise yourself with all its

features and functions

• Ensure that all parts of the tool are present and in good condition

• If any parts are missing or damaged, have such parts replaced before attempting to use this

tool

Before Use

WARNING: Ensure the tool is disconnected from the power supply before attaching or

changing any accessories, or making any adjustments.

Power switch

See Fig I and II

• When the router is connected to power, the Power Switch with Lock-Out Cover (3) will

illuminate (in both 'on' and 'off' positions).

• The retracting switch cover prevents accidental starting of the router. It must be retracted

before the router can be switched on. The cover will remain open until the router is

switched off

Fitting a collet and router bit

See Fig III

1. Ensure the Power Switch with Lock-Out Cover (3) is OFF and the router disconnected from

mains (the retracting shutter will lock closed)

2. Check the depth stop is fully retracted (see ‘Depth Stop and Turret’) and release the Plunge

Lock Lever (7)

3. Turn the machine upside down

4. Plunge the router to its maximum depth and engage the Plunge Lock Lever to lock the

router in this position

Note: On ﬁrst use, when you take the router out of the box, the router is in this position

5. Rotate the threaded spindle as necessary to engage the spindle lock

Fitting a collet

1. Place collet onto the spindle so that it engages the screw threads

2. Turn the collet clockwise by hand so that it is fully mounted onto the spindle

Fitting a router bit

1. Loosen the collet sufﬁciently to insert the router bit. If removing a router bit, use the

Spanner (15) to loosen the collet

2. Insert the router bit fully into the collet, then use the spanner to tighten the collet so that it

holds the bit ﬁrmly

3. Hold the body of the machine securely and disengage the Plunge Lock Lever (7). This will

release the collet lock and the lock-out cover of the power switch

Dust Extraction

Dust Port

• The Triton JOF Router is equipped with a Dust Extraction Port (6) for chip extraction above

the cut. It accepts 38mm (1½") O.D. hose, supplied with the Triton Dust Collector (DCA300)

• The hose screws into position via a left hand thread (anti-clockwise)

Optional template guide kit

• An optional template guide kit is available from your Triton stockist

Extended Baseplate and Fence

See Fig IV

• The Extended Baseplate (16) provides greater stability when using bearing-guided cutters

along an edge

• When using the router with the baseplate ﬁtted, place one hand on the long end of the

base, holding it down onto your work, and grip the router handle, furthest away, with your

other hand

To ﬁt the extended baseplate

1. Loosen the Baseplate Mounting Knobs (13) sufﬁciently so that the bolts (on the mounting

knobs) will be able to engage the keyhole slots in the baseplate

2. Turn the router upside down

3. Push each knob upwards in turn as you slide the baseplate onto the base of the router and

engage the bolts in the keyhole slots on the baseplate

4. Slide the extended baseplate until the bolts locate against the ends of the keyhole slots.

Tighten the baseplate mounting knobs ﬁrmly

To ﬁt the fence

See Fig V

1. Loosen the side fence knobs

2. Slide the Fence (14) onto the rails at each side of the baseplate

3. Lock at the required setting by tightening both fence knobs

Notes

• When routing trenches some distance in from an edge, ﬁt the Fence to the long end of

the base

• When performing edge work with a non-bearing guided cutter, ﬁt the Fence to the short

end of the base

• If using a very large diameter cutter it may be necessary to ﬁx wooden blocks to the fence

faces, via the screw holes, to ensure the cutter does not come into contact with the Fence

Operation

Variable speed control

• Router speed settings are not critical. Generally the highest speed which does not result

in burn marks on the workpiece should be used. Where stated, always follow the cutter

manufacturers’ maximum speed limitations.

• Generally, higher speeds are used for timber and MDF, lower speeds for synthetic materials

• Operating at reduced speed increases the risk of damage to the router as a result of

overload. Use very slow feed rates and/or multiple shallow cuts.

• The Speed Controller (15) is marked 1 to 5, corresponding approximately with the speeds

and cutter diameters below. Turn the dial to select the required speed required.

Setting RPM Cutter Diameter

5 21,000 Up to 25mm

4 18,000 25 - 50mm

3 14,500 50 - 65mm

2 11,000 Over 65mm

1 8,000 Use only if burning

925837_Manual.indd 6 18/05/2017 14:31

Triton JOF 001 Seite 6

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info