Bedienungsanleitung Triton T12AD (Seite 5 von 106) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch)

665021

Zoom out

Zoom in

Vorherige Seite

1/106

Nächste Seite

Battery tools use and care

a) Recharge only with charger speciﬁed by the manufacturer. A charger

that is sutiable for one type of battery pack may create a risk of ﬁre when

used with another battery pack.

b) Use power tools only with speciﬁcally designated battery packs.

Use of any other battery packs may create a risk of injury and ﬁre

c) When battery pack is not in use, keep it away from other metal

objects, like paper clips, coins, keys, nails, screws and other small

metal objects that can make a connection from one terminal to

another. Shorting the battery terminals together may cause a burns or a

ﬁre.

Under abusive conditions, liquid may be ejected from the battery;

avoid contact. If contact accidentally occurs, ﬂush with water. If

liquid contact eyes, additionally seek medical help. Liquid ejected

from the battery may cause irritation or burns

WARNING: When used in Australia or New Zealand, it is recommended that

this tool is ALWAYS supplied via Residual Current Device (RCD) with a rated

residual current of 30mA or less.

Service

a) Have your power tool serviced by a qualiﬁed repair person using

only identical replacement parts. This will ensure that the safety of the

power tool is maintained.

Additional safety for battery-

operated screwdrivers

For safety relating to protective clothing/equipment and general health hazards

relating to power tools; refer to General and Electrical Safety sections in this

manual

Important: It is imperative to follow all national safety regulations concerning

installation, operation and maintenance

• Hold power tools by insulated gripping surfaces, when performing an

operation where the cutting accessory may contact hidden wiring.

Cutting accessory and/or fasteners contacting a “live” wire may make

exposed metal parts of the power tool “live” and give the operator an

electric shock. Do not allow anyone under the age of 18 years to use this

tool, and ensure that operators are qualiﬁed and familiar with the operating

and safety instructions

• If batteries are to be charged outdoors, ensure that the power supply and

charger are protected against weather/moisture

• When using the drill, use safety equipment including safety glasses or

shield, ear defenders, and protective clothing including safety gloves. Wear

a dust mask if the drilling operation creates dust

• Use metal and voltage detectors to locate concealed electric, water or gas

lines. Avoid touching live components or conductors

• Ensure that the lighting is adequate

• Ensure that the drill bit is securely ﬁxed in the chuck. Insecure drill bits can

be ejected from the machine causing a hazard

• Ensure that the drill bit is in contact with the workpiece prior to starting up

the tool

• Before drilling, check that there is sufﬁcient clearance for the drill bit under

the workpiece

• Do not put pressure on the tool, to do so would shorten its service life

• Drill bits get hot during operation, allow to cool prior to handling them

• Never use your hands to remove sawdust, chips or waste close by the bit

• If you are interrupted when operating the drill, complete the process and

switch off before looking up

• Where possible, use clamps or a vice to hold your work

• Examine the chuck regularly for signs of wear or damage. Have damaged

parts repaired by a qualiﬁed service centre

• Always wait until the drill has come to a complete stop before putting it

down

• Periodically check all nuts, bolts and other ﬁxings and tighten where

necessary

• Hold power tools by insulated gripping surfaces, when performing an

operation where the cutting accessory may contact hidden wiring. Cutting

accessory and/or fasteners contacting a ‘live’ wire may make exposed

metal parts of the power tool ‘live’ and give the operator an electric shock.

Battery charger safety

Use the battery charger correctly

• Refer to the section of this manual relating to use of the battery charger

before attempting to charge the battery.

• Do not attempt to use the charger with any batteries other than those

supplied. Keep your battery charger clean; foreign objects or dirt may

cause a short or block air vents. Failure to follow these instructions may

cause overheating or ﬁre

• If the supply cord is damaged, it must be replaced by the manufacturer, its

service agent or similarly qualiﬁed persons in order to avoid a hazard

• Examine the battery charger regularly for damage, especially the cord, plug

and enclosure. If the battery charger is damaged, it must not be used until

it has been repaired

• Children should be supervised to ensure that they do not play with the

appliance

Warning: Do not recharge non-rechargeable batteries

Use batteries correctly

• Only charge batteries using the charger provided. Only use batteries

provided with this power tool, or others recommended by the supplier.

Keep batteries clean; foreign objects or dirt may cause a short. Allow

batteries to cool for 15 minutes after charging or heavy use. Failure to

follow these instructions may cause overheating or ﬁre.

• When not in use batteries should be stored at room temperature (approx.

20˚C). Ensure that batteries cannot accidentally short in storage.

WARNING: Li-Ion batteries, if incorrectly used, stored or charged are a ﬁre,

burn and explosion hazard.

• Keep the battery out of reach of children

• Only charge Li-Ion batteries using the charger provided or designed

speciﬁcally for your product

• Only use Li-Ion batteries provided with a product or speciﬁcally designed to

be compatible

• Allow batteries to cool for 15 minutes after charging or heavy use. Failure

to follow these instructions may cause overheating or ﬁre

• When not in use batteries should be stored at room temperature

(approximately 20˚C)

• Ensure that battery contacts cannot accidentally short in storage. Keep

batteries clean; foreign objects or dirt may cause a short. Keep away from

other metal objects, for example paperclips, coins, keys, nails and screws

• Under abusive conditions, liquid may be ejected from the battery. This

liquid may cause skin irritation or burns. Avoid contact. If contact

accidentally occurs, ﬂush with water. If liquid contacts eyes, seek medical

help

• Do not open, disassemble, crush, heat above 60°C or incinerate. Do not

dispose of in ﬁre or similar

Battery and charger safety features

The battery and charger are ﬁtted with a number of safety features which may

be triggered during charging or operation:

• Over-charge protection: Charger automatically switches off when

the battery has reached full charge capacity, protecting the internal

components of the battery

• Over-discharge protection: Prevents the battery from discharging beyond

the recommended lowest safety voltage

• Over-heat protection: Sensor switches off if the battery becomes too

hot during operation. This can happen if the tool is overloaded or being

used for extended periods of time. Up to 30 minutes cooling time may be

required depending on the ambient temperature

• Overload protection: Battery temporarily stops if it is overloaded or the

maximum current draw is exceeded, protecting the internal components.

The battery will resume normal operation when the current draw returns to

a normal safe level. This may take a few seconds

• Short circuit protection: The battery will stop working immediately if a short

circuit occurs, this prevents damage to the battery or tool

104207_Z1MANPRO1.indd 5 15/08/2014 10:22

Triton T12AD Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info