Bedienungsanleitung Triton TSA 001 (Seite 5 von 53) (Deutsch, Englisch, Holländisch, Französisch, Italienisch, Spanisch)

665061

Zoom out

Zoom in

Vorherige Seite

1/53

Nächste Seite

e) Maintain power tools. Check for misalignment or

binding of moving parts, breakage of parts and

any other condition that may affect the power

tool’s operation. If damaged, have the power tool

repaired before use. Many accidents are caused by

poorly maintained power tools.

f) Keep cutting tools sharp and clean. Properly

maintained cutting tools with sharp cutting edges are

less likely to bind and are easier to control.

g) Use the power tool, accessories and tool bits etc.

in accordance with these instructions, taking into

account the working conditions and the work to

be performed. Use of the power tool for operations

different from those intended could result in a

hazardous situation.

5) Service

a) Have your power tool serviced by a qualiﬁed repair

person using only identical replacement parts.

This will ensure that the safety of the power tool is

maintained.

CIRCULAR SAW SAFETY

WARNINGS. Before connecting a tool to a power source

(mains switch power point receptacle, outlet, etc.) be

sure that the voltage supply is the same as that speciﬁed

on the nameplate of the tool. A power source with a

voltage greater than that speciﬁed for the tool can result

in serious injury to the user, and damage to the tool. If in

doubt, do not plug in the tool. Using a power source with

a voltage less than the nameplate rating is harmful to the

motor.

• Donotallowanyoneundertheageof18yearsto

operate this saw

• Whenoperatingthesaw,usesafetyequipment

including safety goggles or shield, ear protection, dust

mask and protective clothing including safety gloves

• Alwaysuserecommendedbladeswithcorrectsize

and shape of arbor holes e.g. diamond or round.

Blades that do not match the mounting hardware of

the saw will run eccentrically, causing loss of control

• Powertoolsmustalwaysbeheldbytheinsulated

gripping surfaces when performing an operation,

ensuring protection if the cutting tool makes contact

with its own cord or hidden wiring. Contact with a

‘live’ wire will make exposed metal parts of the power

tool ‘live’ and shock the operator if the insulated

gripping surfaces are not used

• Ensurehandsareawayfromthecuttingareaand

blade. Keep one hand on auxiliary handle, or motor

housing. If both hands are holding the tool they cannot

be cut by the blade

• Donotattempttocutmaterialthickerthandetailedin

the Speciﬁcations section of this manual

• Adjustthecuttingdepthtothethicknessofthe

workpiece i.e. less than a full tooth of the blade should

be visible below the workpiece

• Ensurethatworkiscorrectlysupported.Largepanels

may sag under their own weight and bind the saw

blade. Supports must be placed under the panel on

both sides, close to the line of cut and near the edge of

the panel

• Ensureallsupportsandpowercablesarecompletely

clear of the cutting path

• Alwayssecuretheworkpiecetoastableplatform,

ensuring that body exposure is minimised, avoiding

blade binding or loss of control

• Foraccuracyofcut,andtoavoidbladebinding,always

use a rip fence or straight edge guide

• Neverholdaworkpieceinyourhandoracrossyour

legs whilst cutting

• Alwaysstandtoonesidewhenoperatingthesaw

• Beawarethatthebladewillprojectfromtheunderside

of the workpiece

• Donotreachbeneaththeworkpiecewheretheguard

cannot protect you from the blade

• Notethedirectionofrotationofthemotorandthe

blade

• Inspecttheworkpieceandremoveallnailsandother

embedded objects prior to starting work

• Donotapplyanysidewaysortwistingforcetothe

blade whilst cutting

• Ifacutdoesnotextendtotheedgeoftheworkpiece,

or if the blade binds in the cut, allow the blade to

come to a complete stop and lift the saw out of the

workpiece

• Donotattempttofreeajammedbladebeforerst

disconnecting the machine from power

• Donotmovethesawbackwardsatanytimewhilst

cutting

• Bewareofprojectedwaste.Insomesituations,waste

material may be projected at speed from the cutting

tool. It is the users responsibility to ensure that

other people in the work area are protected from the

possibility of projected waste

• Ifyouareinterruptedwhenoperatingthesaw,

complete the process and switch off before diverting

your attention

• Thebladeboltandwasherswerespeciallydesigned

for your saw. For optimum performance and safety of

operation never use damaged or incorrect bolt/blade

washers

• Regularlychecktheoperationofthebladeguard.If

the guard does not automatically cover the blade, have

the saw repaired before use

• Periodicallycheckthatallnuts,boltsandotherxings

have not loosened, tighten where necessary

Safety Instructions

330175_Z1MANPRO1.indd 5 11/07/2012 09:11

Triton TSA 001 Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info