Bedienungsanleitung Trotec HyStream 2100 (Seite 14 von 16) (Englisch)

753329

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

13 EN

Operating manual – heat gun HyStream 2100

Regulating the air flow rate

Info

Regardless of the position of the on/off switch (stage1

or2), the fan stage can be adjusted at any time.

1. Select the desired fan speed by means of the plus/ minus

buttons(14): the air flow rate can be adjusted in 5stages.

2. Briefly press the plus/ minus buttons(14) to increase or

reduce the fan speed.

3. If you press and hold the buttons a bit longer, the flow rate

will be repeatedly increased or lowered until you let go or

the maximum or minimum flow rate has been reached.

Stage Air flow rate Air temperature

Stage 1

Stage 2

250 – 500l/min

50°C

50 – 650°C

The cold setting1 is suited for cooling down a hot workpiece or

for drying paint. Furthermore, it serves the purpose of cooling

the device down before exchanging the attachment nozzles or

before putting the device itself down.

Shutdown

Warning of electrical voltage

Do not touch the mains plug with wet or damp hands.

Warning of hot surface

The insertion tool might still be hot after the

application. Burn hazard when touching the insertion

tool.

Do not touch the insertion tool bare-handed!

Wear protective gloves!

1. Switch the on/off switch(8) to position1 and the fan speed

to stage5. Leave the device running at the cold setting for a

brief period.

2. Put the device up in a vertical position allowing it to cool

down sufficiently.

3. Switch off the device by sliding the on/off switch(8) to

position0.

4. Hold onto the mains plug while pulling the power cable out

of the mains socket.

5. Clean the device according to the Maintenance chapter.

6. Store the device according to the Storage chapter.

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

Troubleshooting tasks which require the housing to be opened

must only be carried out by a specialist dealer or by Trotec.

Slight smoke or odour are emitted during first use:

• This is not a fault. These phenomena disappear after a

brief runtime.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages.

• Check the on-site fusing.

The device has automatically switched itself off:

• Keep the air inlet clear to prevent the motor from

overheating.

• Check whether the overheating protection has tripped, see

chapter Safety.

Info

Wait for at least 10 minutes before switching the

device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorized specialist electrical company or to

Trotec for repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec HyStream 2100 Seite 14

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec HyStream 2100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info