Bedienungsanleitung Trotec PCPS 10-1100 (Seite 13 von 16) (Englisch)

753932

Zoom out

Zoom in

Vorherige Seite

1/16

Nächste Seite

EN 13

compressor PCPS 10-1100

Errors and faults

The device has been checked for proper functioning several

times during production. If malfunctions occur nonetheless,

check the device according to the following list.

Troubleshooting tasks which require the housing to be opened

must only be carried out by an authorized specialist electrical

company or by Trotec.

Light smoke or odour is emitted during the first use:

• This is not a fault. These phenomena disappear after a

brief runtime.

The device does not start:

• Check the power connection.

• Check the power cable and mains plug for damages. If you

notice damages, do not try to take the device back into

operation. To avoid safety hazards, do not perform any

repairs. Send the device to a specialist electrical company

or to Trotec to have the power cable and mains plug

replaced.

• Check the on-site fusing.

• Check the outside temperature. At temperatures

below+5°C, the motor becomes sluggish and can be

difficult or impossible to start up. Do not use the device at

an temperatures below+5°C.

The device is running but there is no apparent inflation/

The pressure gauge shows no pressure:

• Check the valve adapter used for proper fit. Air might be

escaping at the valve of the item to be inflated.

• Let the device run for a moment. The pressure will only be

shown on the pressure gauge after the pressure inside the

item to be inflated has exceeded the ambient pressure.

• Check the item to be inflated for leaks.

• Check the compressed-air gun for proper functioning, and

replace it if necessary.

The device is running but there is no pressure build-up:

• The check valve is leaky. Have the check valve inspected

and, if necessary, replaced by a specialist workshop.

• Check the seals. Have broken seals replaced by a

specialist workshop.

The device is running but the connected accessories do not

work:

• Check the accessories for proper functioning. Replace

defective accessories.

• Check the compressed-air hose and the quick coupling,

and have them replaced by a specialist workshop if

necessary.

The device becomes hot:

Note

The device is not suitable for continuous operation.

Over a period of 10minutes, do not use the device for

more than 1.5minutes in continuous operation. Allow

the device to cool down for the remaining time.

Should the device be overheating nonetheless, switch

the device off and disconnect it from the mains.

Allow the device to cool down sufficiently before

switching it back on.

• Check whether the device is suitable for the tasks to be

carried out.

• Keep the venting slots or air inlet and outlet clear to

prevent the motor from overheating.

Note

Wait for at least 10minutes after maintenance and

repair work. Only then switch the device back on.

Your device still does not operate correctly after these

checks?

Please contact the customer service. If necessary, bring the

device to an authorized specialist electrical company or to

Trotec for repair.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PCPS 10-1100 Seite 13

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PCPS 10-1100

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info