Bedienungsanleitung Trotec PMTS10 - 230V (Seite 4 von 19) (Englisch)

689480

Zoom out

Zoom in

Vorherige Seite

1/19

Nächste Seite

3 EN

300W multi-function tool PMTS 10-230V

• Do not use the power tool if the switch does not turn it

on and off. Any power tool that cannot be controlled with

the switch is dangerous and must be repaired.

• Disconnect the plug from the power source and / or

the battery pack, if detachable, from the power tool

before making any adjustments, changing

accessories, or storing power tools. Such preventive

safety measures reduce the risk of starting the power tool

accidentally.

• Store idle power tools out of the reach of children and

do not allow persons unfamiliar with the power tool or

these instructions to operate the power tool. Power

tools are dangerous in the hands of untrained users.

• Maintain power tools and accessories carefully. Check

for misalignment or binding of moving parts, breakage

of parts and any other condition that may affect the

power tool’s operation. If damaged, have the power

tool repaired before use. Many accidents are caused by

poorly maintained power tools.

• Keep cutting tools sharp and clean. Properly maintained

cutting tools with sharp cutting edges are less likely to

bind and are easier to control.

• Use the power tool, accessories and tool bits etc. in

accordance with these instructions, taking into

account the working conditions and the work to be

performed. Use of the power tool for operations different

from those intended could result in a hazardous situation.

• Keep handles and gripping surfaces dry, clean and

free from oil and grease. Slippery handles and gripping

surfaces do not allow for safe handling and control of the

tool in unexpected situations.

General Power Tool Safety Warnings – Service

• Have your power tool serviced by a qualified repair

person using only identical replacement parts. This will

ensure that the safety of the power tool is maintained.

Safety warnings for multi-function tools

• Hold the power tool by its insulated gripping surfaces

when performing an operation where the cutting

accessory may contact hidden wiring or its own cord.

Contacting a live wire might energize exposed metal parts

of the device and lead to an electric shock.

• Only use the power tool for dry sanding. Water entering

an electrical appliance increases the risk of electric shock.

Warning

Fire hazard! Avoid overheating of the material to be

sanded and the sander. Before taking work breaks

always empty the dust container.

Unfavourable conditions such as flying sparks when

sanding metal render abrasive dust in the dust bag,

micro filter, paper bag (or in the filter bag or filter of the

vacuum cleaner) prone to self-ignition. The risk is

particularly high when the abrasive dust is mixed with

residues of paint, polyurethane or other chemical

substances and the sanding material is hot after a

longer period of work.

• Keep your hands out of the sawing area. Do not reach

underneath the workpiece. Risk of injury upon contact

with the saw blade.

• Use appropriate detection equipment to track down

concealed supply lines or consult the local utility

companies. Contact with electrical lines may result in fire

and electric shock. Damaging a gas line may lead to an

explosion. Penetrating a water line causes property

damage and may cause an electric shock.

• During operation hold onto the power tool with both

hands and make sure you stand firmly on the ground.

It is safer to handle the power tool with two hands.

• Use the anti-vibration handle supplied with the device.

Losing control of the power tool may result in personal

injury.

• Secure the workpiece. The grip of tensioning devices or a

vice is more secure than holding the workpiece only by

hand.

Wear protective gloves when changing the insertion

tools. The applied tools heat up during longer

operation.

• Do not scrape moistened material (e.g. wallpaper) and

not on moist subsurfaces either. Water entering a power

tool will increase the risk of electric shock.

• Do not treat the surface to be processed with liquids

containing solvents. Toxic fumes may be produced

during scraping owing to the heat-up of the materials.

• Exercise particular caution when using scraper and

cutter. These tools are especially sharp involving a risk of

injury.

• Ensure sufficient ventilation when processing plastics,

paints, varnishes etc.

• Wait until the device has come to a standstill, before

putting it down.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PMTS10 - 230V Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PMTS10 - 230V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info