Bedienungsanleitung Trotec PRDS20-20V (Seite 5 von 20) (Englisch)

753295

Zoom out

Zoom in

Vorherige Seite

1/20

Nächste Seite

EN 5

cordless rotary hammer PRDS 20-20V

•During operation hold onto the power tool with both

hands. Make sure that you stand firmly on the ground. It is

safer to handle the power tool with two hands.

•Secure the workpiece. The grip of tensioning devices or a

vice is more secure than holding the workpiece only by

hand.

Protect yourself and others present from injuries

caused by splintering and flying bits and pieces.

Wear a hard hat, eye protection, a dust mask and safety

boots. If necessary, put up partition panels as shield

against breaking off debris.

•Before starting to work, always make sure that the

insertion tool is firmly clamped inside the drill chuck.

Insertion tools that are not locked in place could be

catapulted out of the power tool upon switch-on and lead

to injuries.

•Before switching on the power tool, ensure that the

insertion tool can move freely. If the device is switched

on with a jammed insertion tool, the resulting forces can

be extreme causing the device to kick out sideways.

•Immediately switch off the power tool if the insertion

tool blocks. The power tool can lash out to the side owing

to the forces that build up consequently.

•Regularly check the drill chuck for wear or damage.

•Only start a percussive power tool while holding it

against a workpiece (wall, ceiling, etc.).

•Wait until the power tool has come to a standstill,

before putting it down.

•For any work on the device, as well as during transport

or storage, set the switch for the rotational direction to

centre position (locked). This prevents unintentional

starting of the power tool.

•Processing metal creates flying sparks. Make sure that

nobody's safety is jeopardized and that there are no

combustible materials near the working area. Fire hazard!

•Avoid drilling in lead paint or other harmful materials.

•Always keep the power cable behind the device.

•Make sure that the venting slots are not covered

during operation. Do not insert any objects into the

venting slots.

•The device must always be clean, dry and free from oil

or greases.

Safety instructions when using long drill bits

•Never operate at higher speed than the maximum

speed rating of the drill bit. At higher speeds, the bit is

likely to bend if allowed to rotate freely without contacting

the workpiece, resulting in personal injury.

•Always start drilling at low speed and with the bit tip

in contact with the workpiece. At higher speeds, the bit

is likely to bend if allowed to rotate freely without

contacting the workpiece, resulting in personal injury.

•Apply pressure only in direct line with the bit and do

not apply excessive pressure. Bits can bend causing

breakage or loss of control, resulting in personal injury.

Intended use

Only use the device PRDS 20-20V:

• for hammer drilling in brick, concrete and rock.

If using a keyless drill chuck with SDSshank (not included in

the scope of delivery):

• for screwing in and loosening screws,

• for drilling in wood, plastic, ceramic and metal,

observing the technical data provided.

We recommend using the power tool with original Trotec

accessories.

Foreseeable misuse

The device is not intended for drilling into natural stone or for

chiselling.

Any other use than the one described in the chapter "Intended

use" is regarded as reasonably foreseeable misuse.

Personnel qualifications

People who use this device must:

• have read and understood the instructions, especially the

Safety chapter.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trotec PRDS20-20V Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trotec PRDS20-20V

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info