15
4. Installation with chassis with U-profile and frame
height of between 140 and 185 mm
The U-profile frame kit, 1, 2 or 3 spacer plate sets and
the U-bolt extension kit are required to compensate for the
U-profile frame edge and the height.
5. Installation with chassis with L and U profiles with
frame height of less than 140 mm
With a chassis with a frame height (Y) of less than 140 mm a
flat frame kit must be fitted to compensate for the height.
In Germany, the flat frame kit installation must be
accepted by a vehicle expert.
6. The AL-KO Vario III / AV installation kit must be used
with the AL-KO Vario III / AV chassis with a frame thickness of
less than 2.8 mm.
Special accessory installation
1. U-bolt extension kit
(For frames with L-profile, frame height
from 140 to 185 mm)
U-bolts, nuts and washers,
Art. no. 60010-00100.
1.1. Spacer plate kit
(Two 15 mm spacer plates)
For height compensation
max. 45 mm (3 plates) at each side
(e.g. installed behind axle)
Art. no. 60010-65000.
2. Flat frame kit
For height compensation for
caravan/trailer with frame height of
less than 140 mm,
Art. no. 60010-09400.
In Germany, this installation
kit must be accepted by a
vehicle expert.
3. U-profile frame kit
(For frames with U-profile,
frame height approx. 185 mm)
U-bolt with clamping plates and
self-locking nuts, stoppers,
Art. no. 60010-09200.
4. AL-KO Vario III / AV
Installation kit
For caravans with
AL-KO Vario III / AV Chassis
(frame thickness less than
2.8 mm) mandatory,
Art. no. 60010-21500.
5. Cross actuation device
(For swivelling both drive units
against the wheels from one
side and releasing them again)
Connecting tube, middle tube,
nuts, bolts, grub screws,
Art. no. 60010-18500.
The Caravan Mover/Euro Mover is not approved for
installation on caravans/trailers with any other
chassis! Any drilling (exception: when using flat frame kit) or
welding to the chassis is not allowed. Under no circumstances
remove any suspension components from the chassis.
Approval
Declaration of conformity:
The Truma Caravan Mover and Euro Mover meet the basic re-
quirements of machinery directive 98/37/EC and are therefore
entitled to bear the CE symbol.
The Euro Caravan Mover and Euro Mover have design approval
and a general operating permit (ABE) has been issued for Ger-
many. Acceptance by a vehicle expert is not required (except
when installing the flat frame kit). The ABE must be kept in the
vehicle.
When installing the Mover always observe the technical and
administrative rules and regulations of the country in which the
vehicle is to be registered for the first time.
Any modification to the unit, or the use of spare parts and
functionally-important accessories which are not original
Truma components, or failure to respect the installation and
operating instructions, will lead to the cancellation of the guar-
antee and to exclusion of claims for liability. in addition to this,
the operational approval for the device will be cancelled.
Tools and facilities required
To install the unit you will need:
13 mm AF socket / wrench 13 mm AF combination spanner
Torque wrench (automotive size)
Cable cutter/Crimping tool
Power drill / screwdrivers / 25 mm hole cutter
Portable 2 tonne trolley jack and axle stands to suit
Appropriate lighting
Choice of location
We recommend to fit the Mover behind the rear axle. Under
special circumstances (for example lack of space) the Mover
can also be fitted in front of the front axle. Only the provided
U-bolts must be used to attach the Mover (or the U-bolt exten-
sion special accessory).
The frame of the vehicle must be kept free of rust and heavy
soiling and without any damages to the suspension compo-
nents.
The caravan must be fitted with the same size and type of tyre
on each wheel; to ensure the wheel diameter is identical, we
recommend to install and set up the mover only with new
tyres, these are to be inflated to manufacturer’s specifications.
The Caravan Mover weighs approximately 30 kg, the
Euro Mover weighs approximately 32 kg. Ensure the pay
load allowance of the caravan can accommodate this.
Installation of the drive units
The AL-KO Vario III / AV installation kit (Art. no. 60010-
21500) must be used for caravans with the AL-KO Vario III /
AV chassis (frame thickness less than 2.8 mm). For installation
see instructions provided with installation kit.
1. Fig. A: Remove all components from packing and place on
the floor.
2. Loosely screw all components together to form a cross
strut. Nuts must be no more than finger-tight.
