Bedienungsanleitung Trumatic Ultraheat (Seite 5 von 28) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Polnisch, Schwedisch, Norwegisch, Finnisch)

484606

Zoom out

Zoom in

Vorherige Seite

1/28

Nächste Seite

Ultraheat

Intended use

The Truma Ultraheat supplementary heating unit was designed

in the formats with part no. 30402-01 to 07 for the heating

units Trumatic S 3002 (P) as from date of manufacture 07/81,

Trumatic S 5002 as from 04/98 (with new semi-circular clad-

ding) and in the design formats with part no. 30402-08 to 14

for the Truma S 55 T heater.

Use with Trumatic S 3000 P, S 3002 K, S 5002 K and

Trumatic S 5002 up to model 04/98 (with old rectangular

cover) is not permissible.

Other forms of use are also possible after consultation

with Truma.

Approval

Declaration of conformity

The Truma Ultraheat has been tested by the DVGW as an aux-

iliary electric heater and complies with gas equipment direc-

tive 90/396/EEC, EMC directive 2004/108/EC, low voltage di-

rective 2006/95/EC, heating equipment directive 2001/56/EC,

the End-of-Life Vehicles Directive 2000/53/EC and the associ-

ated EC directives and is entitled to bear the CE symbol.

The CE Product Identity Number of the heating system

remains valid without change.

Regulations

Guarantee claims, warranty claims and acceptance of liability

will be ruled out in the event of the following:

modifications to the unit (including accessories),

modifications to the exhaust duct and the cowl,

failure to use original Truma parts as replacement parts and

accessories,

failure to follow the installation and operating instructions.

Furthermore, the approval for operating the appliance will

become invalid and in some countries also the approval for

operating the vehicle.

–

The appliance may only be installed and repaired by an

expert. Before starting work, carefully read and follow the

installation instructions!

Installation in new vehicles

Fig. A

Break out perforated section (1) on the exterior of installation

box (2) for passing through the control electronics.

Trumatic S 5002 only:

Break out the lower part of the interior of installation box (3)

at perforation (4).

Insert heating element (5) from the inside of installation box (2)

and fasten by means of six B 3.5 x 9.5 mm screws (6).

Install installation box (2), installation box (3) and Trumavent

fan as per installation instructions included with the heater.

If connected in series, a mounting and holding device is

of advantage.

Carry out further installation work in accordance with the

installation instructions enclosed with the heater.

–

Installation instructions

Retrofitting in existing vehicles

Dismantling heater

Shut the fast-acting stop valves on the gas supply and gas

cylinder.

Remove the heater cover.

Fig. B

Unscrew gas supply (7) underneath the vehicle.

Loosen exhaust duct sealing plate (8) by means of screw (9)

and turn to detach. Pull exhaust duct (10) completely out of

the sleeve.

Unscrew locking screws (11) on the heater base and remove

the heater completely.

Fig. C

Unscrew locking screws (12) on installation box (2) and

remove the latter.

Preparatory work and installation boxes

For S 3002 (P) up to model 05/98 only

Fig. C

Position the enclosed stencil in the middle of the installa-

tion box interior so that the lower edge of the stencil is flush

with the upper edge of the recess (14) in the installation

box. Mark the six holes for the fastening screws and the

corner points for the control electronics lead-through. Drill

eight holes with a diameter of 4 mm.

Create an opening (1) for the control electronics by cutting

into the side (with sheet-cutting shears) and then bending

back to the rear wall.

For S 3002 (P) from model 05/98, S 5002 and S 55 T only

Fig. A

Break out prepunched opening (1) on the in stalla tion box

exterior (2) for the control electronics leadrough.

Trumatic S 5002 with new semi-circular cover only

Fig. A

Unscrew the lower locking screws (15) on the rear side of

the installation box and break out the lower section of

installation box interior (3) at perforation (4).

Installing the heating element

Fig. A

Insert heating element (5) from the inside of installation box (2)

and fasten from the rear with six B 3.5 x 9.5 mm screws (6).

Reinsert complete installation box (2) and secure with

six screws (12).

Installing heater

Fig. B

Position the heater in the base cut-out and re-fasten with the

five locking screws (11).

Fig. D + E

Connecting the exhaust duct to the heater:

The Biege-Boy (Fig. F – part no. 30030-33000) is a sub-

stantial help when bending the stainless steel exhaust

duct and fitting the O-ring.

–

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Trumatic Ultraheat Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Trumatic Ultraheat

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info