774517
5
Zoom out
Zoom in
Vorherige Seite
1/77
Nächste Seite
8 9
EN ZSDR-850 ZIGBEE SMOKE DETECTOR ZSDR-850 ZIGBEE SMOKE DETECTOR EN
1. REMOVE BATTERY PULL STRIP
A Remove the detector from the mounting bracket by twisting it.
B Remove the battery pull strip by pulling it from the detector.
Only after removing the pull strip the detector can be used.
2. INDICATORS
The detector contains a LED indicator to show the status of the
detector. Please see below the meaning of the dierent LED
indications.
LED FUNCTION TABLE
Connection mode LED will flash fast for approximately 1 min.
Connected successfully LED will light up for 3 sec (The App will also
indicate when the connection is successful)
Detector reset LED will flash 6x
Detector alarm LED will flash and detector will sound (85db). To
stop the detector alarm press the Test/Stop button
Detector operation LED will flash once every 53 sec to indicate the
detector is operating correctly
Battery low indication LED will flash once and gives one beep every
53 sec
3. DOWNLOAD APP
To connect the detector with a
Z1 Zigbee bridge or ICS-2000,
first get the App by scanning
the QR code or go to trust.com/
Zigbee and install it.
4. CONNECT DETECTOR
A In the App, select a room,
press the + button and
choose Trust Zigbee line/
Smoke detector and follow the
instructions. For manual set up
of push-notifications go to the
rules tab, press the + button
and select notification wizard.
5. MOUNT THE DETECTOR
A Mount the bracket of the
detector on a flat surface on
the ceiling and secure it with
the included screws.
B 1 Place the detector on the
mounting bracket.
2 Secure the detector by
twisting it on the bracket
to lock it.
6. TEST MODE
Activate the test mode of the
detector to check the operation
by pressing the Test/Stop
button. The LED will flash fast
and the detector will sound.
RESET DETECTOR AND
ACTIVATE CONNECT MODE
Warning: This step will
disconnect the detector from
the Z1 Zigbee Bridge or the
ICS-2000. To reset the detector
press the button in the hole
at the side for approximately 5
sec with the included pin. The
LED will flash 6x to confirm
the reset.
5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Trust ZSDR-850 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info