Bedienungsanleitung Ulma FURNACE 20kW (Seite 3 von 10) (Englisch)

698957

Zoom out

Zoom in

Vorherige Seite

1/10

Nächste Seite

Information

• Keep this manual so that it is accessible to professionals and future needs.

• Read this manual carefully before starting up the furnace.

• The efficiency of the furnace is calculated after the maximum amount pellets that can be fed and combusted

in the burner during 1 hour (intended for combustion of normal wood pellets as an average of the fuel

specification).

• Follow the manual and its instructions carefully to do recommended management and maintenance.

Registration to the local building authority in your municipality

N.B.: At every change of heating system, the local building authority of the municipality has to be

contacted and a so called “Construction Registration” is made.

Inspection

Heating plants installed today shall be inspected and approved by authorized inspector like the local

certified chimney-sweeper. The local building authority in the municipality can inform you how this

could work.

Important at installation

• Installation shall be made by certified ventilation and sanitation engineer and electrician.

•. N.B.! The burner shall be inserted to maximum in the furnace. Control this carefully in the future

also if the burner is disconnected for example cleaning and service.

• At adjustment of the burner draw limiter shall be adjusted after the draft condition of the chimney. .

• The furnace shall be connected electrically via an all-pole breaker with at least 3 mm length of

break. .

Sweeping

Chimney sweeping made in accordance with the fire-protection law shall be made frequently during

the year. This is made by your local chimney sweeper. Regular cleaning of heating surface of the

furnace shall be made in a way so that good operating economy is obtained. Prepare sweeping by

turning off the burner at least a couple of hours before cleaning to minimize the amount of ignited ash.

Warning!

See to that the power to the furnace is turned off before the cap over the burner is removed and

dismount cabling to the burner when the burner is removed from the furnace.

Maintenance agreement increases operation length and life of the unit

ULMA AB recommends subscription of annual maintenance agreement.

For more information contact your local ULMA retailer.

Change of wear parts

ULMA AB always recommends that wear parts, when needed, are being changed by an authorized

service technician at your ULMA retailer. ULMA’s retailers can provide necessary spare parts and at

change make sure that the part being changed on the unit go through alignment and that a flue-gas

analysis of the unit is made.

Function & description

ULMA FURNACE

Belongs to a new generation of pellet furnace that is specially built only for pellet combustion which means that it

has a standing convection system and special design of the hearth to catch the smallest soot particles on the

convection surfaces and longest possible flue-gas way to increase the efficiency.

Sweeping

Regular cleaning of heating surfaces is made from the top by taking off the lid placed in the center on the top of

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Ulma FURNACE 20kW Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info