Bedienungsanleitung UWATEC Galileo Sol (Seite 78 von 80) (Englisch)

550277

Zoom out

Zoom in

Vorherige Seite

1/80

Nächste Seite

5. Taking care of Galileo



NOTE:

- After a dive, Galileo stores tissue

saturation data once an hour while

on the surface until it is completely

desaturated. If you change the

battery while Galileo has remaining

desaturation time, the tissue data

will not be lost, but Galileo will

reference the last stored data set. As

a consequence, the data displayed

on the surface screen after the

battery change (desaturation time,

surface interval, no-ﬂ y time and

CNS O

) may be different from the

values displayed just prior to the

battery removal.

- After replacing the battery, you must

set the date and time.

5.2.2 Replacing the battery in the

Smart transmitter

WARNING

We recommend having the battery of the

transmitter replaced by an authorized

SCUBAPRO UWATEC dealer. The change must

be made with particular care in order to

prevent water from seeping in. The warranty

does not cover damages due to an improper

placement of the battery.

For best results, use the transmitter battery

set PN 06.201.920, comprising a CR2450

battery and a 26.00 x 2.00 mm transmitter

cap o-ring.

WARNING

- Never touch the metal surface of the battery

with bare ﬁ ngers. The two battery poles

must never be short circuited.

- A leaking transmitter cap may lead to the

destruction of the transmitter by water

seeping in or cause the transmitter to

switch off without prior notice.

- Always open the transmitter in a dry and

clean environment.

- Only open the transmitter to replace the

battery.

1. Remove the transmitter from the HP

port of the ﬁ rst stage regulator.

2. Dry the transmitter with a soft towel.

3. Remove the 3 screws with a Phillips

screwdriver.

4. Carefully remove the transmitter cap.

5. Carefully remove the transmitter cap

o-ring. Be careful not to damage the

sealing surfaces.

6. Remove the battery by holding it on

both sides. Do not touch the contacts

or the electronic parts.

WARNING

If you notice traces of seeping water, damages

or other defects on the o-ring, do not use the

transmitter for further dives. Take it to an

authorized SCUBAPRO UWATEC dealer to be

checked.

7. Always insert a new o-ring when you

replace the battery and dispose the

old o-ring. Make sure that the new,

lubricated o-ring is in perfect condition,

and that o-ring, o-ring groove and the

sealing surface of the transmitter and

transmitter cap are free of dust and

dirt. If necessary, clean the parts with

a soft cloth. Fit the o-ring in the o-ring

groove.

8. Wait for 30 seconds, then insert the

new battery. Ensure that the “+” side

is facing away from the transmitter. The

transmitter can be damaged if you do

not insert the battery correctly.

9. The transmitter will now perform an

automatic test and switch into ready

mode after 60 seconds.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

UWATEC Galileo Sol Seite 78

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von UWATEC Galileo Sol

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info