Bedienungsanleitung Varo MOTSA15EL (Seite 1 von 2) (Englisch)

622521

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

MOTSA10EL, 12EL, 15EL & 19EL EN

OPERATION INSTRUCTIONS

CAUTION: Do not keep the keys in the safe.

1 OPEN THE SAFE FOR THE FIRST TIME

To open the safe for the first time, remove the small plastic cover on the front panel, insert the

key into the lock and turn it counter-clockwise, at the same time, turn the knob clockwise and

open the door.

2 INSTALLING THE BATTERIES.

The safe requires 4× size ‘AA’ (1.5V/R06) batteries. Remove the battery cover and install the

batteries into the compartment. Ensuring the batteries are fitted with the correct corresponding

polarity. The display will scan the status of the electronic lock system automatically. If it is in

order, the display will show ‘good’.

3 OPENING THE SAFE AFTER INSTALLING BATTERIES

To open the door of the safe, press the button ‘START’, the display on the panel will show ‘----

----’, then input one of the two sets of factory-preset codes:

0,0,0,0 (user code) or 8,8,8,8 (master code) immediately and confirm by pressing the button

‘START’. You will hear a musical sound with the display showing ‘OPEN’ and open the safe

using the knob within approximately 4 seconds.

4 PROGRAMMING THE CODE

NOTICE: The safe can be programmed with two sets of codes. For your safety, after

opening the safe and installing the batteries, you should program two sets of your new

codes to take the place of two sets of factory-preset codes.

4.1 Programming the user code

A. With the door of the safe open, press the red button (located on the inside of the door near

the hinge) and the display will show ‘SET CodE’.

B. Now press from 3 to 8 numbers that you wish to use as a new user code, and confirm by

pressing the button ‘START’. After hearing a musical sound, the display will show ‘IN’ and your

inputting numbers. It means that the new user code is confirmed.

4.2 Programming the master code

A. Press the red button then press the button ‘START’. The display will show ‘oLd CodE’.

B. Now input the original master code (factory preset code: 8,8,8,8) and press the button

‘START’. The display will show ‘SET’. Now press from 3 to 8 numbers that you wish to use as

a new master code, and confirm by pressing the button ‘START’. The display will show ‘rE-

InPUT’.

C. Now enter your inputting numbers again and confirm by pressing the button ‘START’. After

hearing a musical sound, the display will show ‘IN’ and your inputting numbers. It means that

the new master code is confirmed.

If you or an intruder uses the incorrect group of numbers, you will hear a beep with the display

showing ‘Error’ and it will not open. If the incorrect combination code is used 4 times

consecutively, the display will show ‘Error’, the buzzer will sound for approximately 3 minutes.

The correct code cannot be entered until after this 3 minutes delay. The override key can

however be used to open the door during this three minutes. If the key is used to open the

door, the buzzer can be cleared by pressing the red button.

If you do not want the display to show your codes or numbers when you open the safe, just

press the button ‘START’ twice at the first time of pressing and other steps are the same.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Varo MOTSA15EL Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Varo MOTSA15EL

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info