Bedienungsanleitung VDO A8 (Seite 2 von 3) (English)

34239

Zoom out

Zoom in

Vorherige Seite

1/3

Nächste Seite

5. Programming of computer

To show Speed and calculate Trip Distance and the other data, your VDO A8 needs the precise wheelsize = wheel circumference

(in mm or inch) of your bike.

5.1 HOW TO DETERMINE YOUR WHEELSIZE:

The wheelsize setting can be done with an accuracy of 1 mm or 0.1 inch.

The table below shows the most common tire sizes and the related wheelsize-data in mm and inch.

This data not necessarily corresponds with the correct data of your bike.

If your Tyre Size is not shown in the Table, you can ﬁnd your correct wheelsize as explained below:

STEP 1 Stand your bicycle upright. With your tyre inﬂated to its proper pressure, rotate your front wheel so that the valve is located at

the bottom (6 o’clock position). Make a mark on the ﬂoor to indicate the valve location.

STEP 2 Roll the bicycle forward in a straight line for one complete wheel revolution, until the valve is again at the bottom. Make a

mark on the ﬂoor to indicate this valve location.

STEP 3 Measure the distance between the marks in millimetres or inches (1 inch = 25.4mm). This value is your wheel size = wheel

circumference.

5.2 SELECTION OF km OR m-READING

The VDO A8 can show speed and all related data either in km or Miles. You can switch at any time from km to m-reading

and vice versa. All data TRP, AVS, MXS, ODO will automatically be re-calculated.

STEP 1 Get TRP in display, press and hold SET-button for 3 sec.

STEP 2 km or m are ﬂashing. Use MODE-button to select km or m-reading.

STEP 3 Press SET-button to conﬁrm above selection. The A8 will now show the set-mode for the wheelsize = wheel

circumference.

5.3 PROGRAMMING THE WHEELSIZE

After pressing SET-button to conﬁrm km or m selection, the A8 will now show the set-mode for the wheelsize = wheel circumference.

Factory settings for wheelsize are 2155 mm for km-reading and 84, 8 inch for m-reading.

Attention: For km-reading the wheelsize needs to be set in mm, for m-reading the wheelsize needs to be set in inches.

STEP 1 Change the ﬂashing wheelsize-digit to requested value by pressing the MODE-button.

STEP 2 Press SET-button to conﬁrm this setting and move to next digit.

STEP 3 Repeat Step 1 and Step 2 until all digits have been set to your wheelsize.

STEP 4 Press and Hold SET-button for 3 sec. to ﬁnish Wheelsize-Setting and return to TRP-display.

5.4 CLOCK SETTING

Your VDO A8 shows actual time in 24:00 (hh:mm) format.

STEP 1 Get CLK into display. Press and Hold SET-button for 3 sec. The Clock SET-Mode will be shown in display.

STEP 2 Use the MODE-button to change the ﬂashing hour-digits. Hold MODE-button for fast setting.

Conﬁrm your settings by pressing the SET-button. This conﬁrmation will also change to Minute-setting.

STEP 3 Use the MODE-button to change the ﬂashing Minute- digits. Hold MODE-button for fast setting.

STEP 4 Press and hold SET-button for 3 sec. to ﬁnish Clock-Setting and return to CLK-display.

5.5 PROGRAMMING OF ODOMETER

The total distance counter ODO can be programmed anytime, for example after a change of battery or to enter the ODO data of your old

computer into your new A8.

STEP 1 Get ODO into display, press and Hold SET-button for 3 sec. The ODO-Set-Mode will be shown in display.

STEP 2 Press MODE-button to change the ﬂashing digit to requested value.

Conﬁrm this setting by pressing the SET-button and simultaneously change to next digit (ﬂashing).

STEP 3 Repeat STEP 1 and STEP 2 until all digits have been set to requested value.

STEP 4 Press and Hold SET-button for 3 sec. to ﬁnish ODO-setting and return to ODO-display.

P06

P07

P08

P09

WS in mm / inch

P05

CYCLECOMPUTING

Instruction manual A8

Tire size WS in mm KMH WS in inch MPH

47-305 16x1,75 1272 50,1

47-406 20x1,75 1590 62,6

34-540 24x1 3/8 1948 76,7

47-507 24x1,75 1907 75,1

23-571 26x1 1973 77,7

40-559 26x1,5 2026 79,8

44-559 26x1,6 2051 80,7

47-559 26x1,75 2055 80,9

50-559 26x1,9 2060 81,1

n/a 26 x 1,95 2070 81,5

54-559 26x2,00 2075 81,7

n/a 26 x 2,1 2080 81,9

57-559 26x2,125 2133 84,0

37-590 26x1 3/8 2105 82,9

Tire size WS in mm KMH WS in inch MPH

20-571 26x3/4 1954 76,9

32-630 27x1 1/4 2199 86,6

40-622 28x1,5 2224 87,6

47-622 28x1,75 2268 89,3

40-635 28x1 1/2 2265 89,2

37-622 28x1 3/8 2205 86,8

18-622 700x18C 2102 82,8

20-622 700x20C 2114 83,2

23-622 700x23C 2133 84,0

25-622 700x25C 2146 84,5

28-622 700x28C 2149 84,6

32-622 700x32C 2174 85,6

37-622 700x37C 2205 86,8

40-622 700x40C 2224 87,6

P05

P06

P07

MINIMUM WS: 100 mm / 3,94“

MAXIMUM WS: 3999 mm / 157,44“

P08

P09

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

VDO A8 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von VDO A8

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info