622294

Velleman DVM68 Seite 9

9
Zoom out
Zoom in
Vorherige Seite
1/55
Nächste Seite
DVM68
25.02.2011
9
Continuity test
• Press the / .button until the symbol appears on the display.
• Connect the test leads to the circuit under test.
• When the measured resistance is less than 50
Ω a continuous beep is produced and the
resistance value
is showed on the display. Should the measured resistance exceed the
selected range or in case of an open circuit, the display will show “OL
”.
Diode test
• Press the / .button until the symbol appears on the display.
•
Connect the red test lead to the anode; connect the black test lead to the cathode of the
diode. The meter will display the approximate forward voltage drop. If the lead connection is
reversed, the meter will display “OL”.
Notes:
•
Never perform continuity or diode measurements on a live circuit and make sure all
capacitors are completely discharged.
•
Measuring diodes that are part of a circuit might produce faulty results.
disconnecting them from the circuit.
7.5 Capacitance measurements
Do not perform capacitance measurements on live circuits.
• Connect the red test lead to the "mA Cx
" jack and the black lead to the "COM" jack.
• Set the rotary switch to nF or µF.
• Connect the test probes to the capacitor. Mind the
polarity when measuring polarized
capacitors.
• The capacitance value is shown on the display.
Notes:
o It takes a few seconds before the meter stabilizes
. This is normal behavior.
o
The range control mode in capacitance measurement is manual ranging and only t
ranges (326nF, 32.6µF) are provided.
o
If Range Control Button is used in this measuring function, decimal points may be at
incorrect positions.
o
At the nF range, when the capacitor to be measured is not connected to test leads, the
LCD may not read zero, but a few counts. These counts
have to be substracted from
measuring results.
o
When the capacity is higher than the measuring range, the display shows ‘OL’.
o
Never perform capacitance measurements on a live circuit and make sure all capacitors
are completely depleted.
7.6 Frequency
measurements
Do not perform frequency measurements in circuits with voltages >
III of 1000V CAT II
Always be careful when working with voltages above 60Vdc or 30Vac rms. Keep your
fingers behind the probe barriers at
all times during measurement.
terminals when the meter is linked to a circuit which is being tested.
• Connect the red test lead to the "VΩF
" jack and the black lead to the "
• Set the rotary switch to Hz.
• Connect the test probes to the circuit.
• The frequency is shown on the display.
Notes:
o
The input voltage should be between 200mV and 10V rms AC. If the voltage is more than
10V rms, reading may be out of the accuracy range.
o When the frequency is higher than the measuring range, t
he display shows ‘OL’.
o
Use a shielded cable for measuring small signals in a noisy environment.
Rev. 01
©Velleman nv
Ω a continuous beep is produced and the
is showed on the display. Should the measured resistance exceed the
”.
Connect the red test lead to the anode; connect the black test lead to the cathode of the
diode. The meter will display the approximate forward voltage drop. If the lead connection is
Never perform continuity or diode measurements on a live circuit and make sure all
Measuring diodes that are part of a circuit might produce faulty results.
Consider
" jack and the black lead to the "COM" jack.
polarity when measuring polarized
. This is normal behavior.
The range control mode in capacitance measurement is manual ranging and only t
wo
If Range Control Button is used in this measuring function, decimal points may be at
At the nF range, when the capacitor to be measured is not connected to test leads, the
have to be substracted from
When the capacity is higher than the measuring range, the display shows ‘OL’.
Never perform capacitance measurements on a live circuit and make sure all capacitors
Do not perform frequency measurements in circuits with voltages >
600V CAT
Always be careful when working with voltages above 60Vdc or 30Vac rms. Keep your
all times during measurement.
Do not touch unused
terminals when the meter is linked to a circuit which is being tested.
" jack and the black lead to the "
COM" jack.
The input voltage should be between 200mV and 10V rms AC. If the voltage is more than
he display shows ‘OL’.
Use a shielded cable for measuring small signals in a noisy environment.
… 9 …

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Velleman DVM68 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info