Bedienungsanleitung Vermeiren Gemini 2 (Seite 29 von 32) (Englisch)

797927

Zoom out

Zoom in

Vorherige Seite

1/32

Nächste Seite

Gemini 2

2014-09

Page19

3.10 Tyre changing

L NOTE: Always make sure that the wheels are sufficiently inflated, since it could

affect the driving behaviour.

L NOTE: We do not accept any liability for wheels not supplied by the

manufacturer.

L NOTE: There must be no air in the tube before it can be removed.

L CAUTION: Chance of damage - If handled improperly, the rim might be damaged.

Rather let an expert perform these activities.

If you want to change the tyres or inner tubes, you should note the following:

1. Let all the air out of the inner tube.

2. Insert a tyre lever between the tyre and the rim.

3. Slowly and gently push the tyre lever downwards. This will pull the tyre over the edge

of the rim.

4. Then move the lever along the rim, the tyre will jump out.

5. Now carefully remove the tyre from the rim and then remove the tube.

L NOTE: Only an expert can guarantee correct assembly. Work not done by your

specialist dealer, would void the warranty of claims.

L WARNING: Chance of damage and injury - When mounting a tyre, make sure no

objects or body parts are pinched between the tyre and the rim.

L CAUTION: Chance of damage - When inflating the tyres, always check that the

pressure is correct. The correct pressure is given on the tyre walls.

L CAUTION: Chance of damage - Use only inflating equipment which complies

with regulations and indicates the pressure in bar, or use the supplied air pump.

We do not accept any liability for damage caused by using inflating equipment

not supplied by the manufacturer.

Note the following before inserting the new inner tube:

Check the rim bed and the inside wall of the tyre for foreign matter and clean these properly

if necessary. Check the condition of the rim bed, especially around the position of the air

valve.

Please use only genuine original replacement parts. We do not accept any liability for

damage caused by non-genuine parts. Kindly contact your specialist dealer.

Place the rim belt in position over the air valve before inserting it into the

rim. Then the rim belt can be pulled over easily. Check that all spoke

heads are covered (a rim belt is not required in the case of a plastic rim).

Push the tyre over the edge of the rim, starting behind the air valve.

Inflate the tube slightly until it is round, and place it inside the tyre.

If the tube fits snugly inside the tyre without any folds (in the case of folds:

let out some air), then the upper side of the tyre can be pressed lightly

onto the rim with both hands, starting at the air valve.

Check all around on both sides that the tube is not pinched between the rim and the edge of

the tyre. Lightly push the air valve inwards and pull it out again to make sure that the tyre is

positioned properly in the region of the air valve.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vermeiren Gemini 2 Seite 29

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Vermeiren Gemini 2

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info