Bedienungsanleitung Visonic PowerMax Express (Seite 34 von 36) (Englisch)

580333

Zoom out

Zoom in

Vorherige Seite

1/36

Nächste Seite

34 D-302989

function. Instead the PowerMaxExpress dials telephone

numbers and reports the event to central stations and/or

to private telephones, as programmed.

• 24 Hour Zone - Audible. - Upon detection, this zone

initiates a siren alarm. The PowerMaxExpress also dials

telephone numbers and reports the event to central

stations and/or to private telephones, as programmed.

C14. Key Zones (Optional)

Key zones are zones that can be used for arming and

disarming the system by MCT-100 and MCT-102

PowerCode transmitters that are enrolled to a zone. In

addition, the alarm system may be armed / disarmed by a

keyswitch when connected to wired zone 29.

Defining a zone as a KEY ZONE includes the following actions:

a. The zone should be defined as non-alarm type zone

(see par. 4.3).

b. "Z-KEY ENABLE" should be selected for such a zone

(see par. 4.3).

c. According to the zone number, "z. 21-28 enable", "z.29

enable", or "z. 21-29 enable" should be selected in the

DEFINE PANEL menu (see par. 4.4.39).

APPENDIX D. PowerMaxExpress Compatible Devices

D1. PowerMaxExpress Compatible

Detectors

Each detector compatible with the PowerMaxExpress

system is packed with its own installation instructions.

Read them carefully and install as indicated.

A. PIR Motion Detectors

The wireless passive infrared (PIR) motion detectors used

in the system are of the PowerCode type. The

PowerMaxExpress is capable of “learning” each detector’s

identification code and linking it to a specific zone (see par.

4.3 in this Guide). Some units are shown below:

K9-85 MCW

MCPIR-3000

or K-940 MCW

DISCOVERY

K9-80/MCW

Note: K-940 MCW, Discovery K9-80/MCW and NEXT

K9-85 MCW are pet immune units.

In addition to its unique 24-bit identification code, each

detector transmits a message, containing status

information:

• The detector is in alarm (or not).

• The detector is being tampered with (or not).

• The battery voltage is low (or normal).

• “This is a supervisory message”.

If any of these detectors detects motion, it sends out a

message to the alarm control panel. If the system is in the

armed state, an alarm will be triggered.

B. Magnetic Contact Transmitter

MCT-302 is a PowerCode magnetic-

contact transmitter used to detect the

opening of a door or a window.

The alarm

contacts are closed as

long as the door or

window remains

closed.

MCT-302

The unit has an extra alarm input that acts as if it were a

separate wireless transmitter. It sends (or does not send) a

“restored to normal“ message to the alarm system,

depending on the setting of an on-board “DIP” switch. The

“restore” message informs you, through the control panel’s

display, whether the door or window is open or closed.

C. MCT-100 Wireless Adapter for Wired Detectors

MCT-100 is a PowerCode device used

mainly as a wireless adapter for 2 regular

magnetic switches installed on 2 windows in

the same room. It has two inputs, behaving

as separate wireless transmitters with

different PowerCode IDs. Each input sends

(or does not send) a “restored“ message to

the alarm system, depending on the setting

of an on-board “DIP” switch.

MCT-100

D. Wireless Smoke Detector

MCT-425. A photoelectric smoke

detector equipped with a

PowerCode-type transmitter. If

enrolled to a fire zone, it initiates a

fire alarm upon detection of smoke.

MCT-425

E. Glass Break Detector

MCT-501 An acoustic detector

equipped with a PowerCode-type

transmitter. Since it restores

automatically after detection, this unit

does not send a restoral message to

the control panel.

MCT-501

D2. PowerMaxExpress Compatible

Transmitters

The PowerMaxExpress system is compatible with multi-

button and single button key-ring and hand-held

transmitters that use PowerCode and CodeSecure coding

methods.

Multi-button PowerCode transmitters transmit the same

code each time the same button is pressed. They can be

used for emergency signaling. They can not be used for

arming / disarming.

CodeSecure transmitters are of the rolling code type - they

transmit a new code each time the same button is pressed.

This provides a higher security level, especially in arming /

disarming applications, because the code can not be

copied (“grabbed”) by unauthorized people.

Following are the basic details of several compatible

transmitters. The possible applications for each push-

button are indicated in each drawing.

A. MCT-234

‘Keyfob’ transmitter. You

can program the AUX

(auxiliary) button to perform

various tasks, in

accordance with the user’s

needs.

Pressing AWAY and

HOME together for 2 sec.

initiates PANIC alarm.

Pressing AWAY for 2 sec.

initiates Latchkey arming.

DISARM

AWAY

AUX

HOME

MCT-234

B. MCT-231 / 201*

(N.A. in North America)

Single-button pendant units.

The MCT-231 (Code- Secure)

and the MCT-201

(PowerCode) can be enrolled

to perform functions as shown.

Both units look alike.

MCT-231 / 201

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic PowerMax Express Seite 34

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Visonic PowerMax Express

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info