Bedienungsanleitung Visonic SR-740 PG2 (Seite 3 von 4) (Englisch)

734994

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

D-304921 SR-740 PG2 Installation Instructions 3

Step 6 Step 7 Step 8

Notes:

1. If the siren is already enrolled, you can

configure the siren parameters and assign

partitions via the “Modify Devices” option –

see Step 2.

2. PARTITIONS will appear only if

PARTITIONING was previously enabled in a

panel that supports the Partitioning feature (for

further details, see "Partitioning" in the

PowerMaster Installer Guide).

3. When there is an alarm, the siren will sound

regardless of partition assignment.

Enter PARTITIONS.

See Note 2

Assign partitions to the

detector by pressing the

, and

buttons on the panel

Select the "DEV SETTINGS"

option and refer to the section

below to configure the siren

parameters.



 means scroll and select

. .

. CONFIGURING THE SIREN PARAMETERS

CONFIGURING THE SIREN PARAMETERSCONFIGURING THE SIREN PARAMETERS

CONFIGURING THE SIREN PARAMETERS

Enter the menu and follow the configuration instructions for the SR-740 PG2 outdoor siren as described in the following

table.

Option Configuration Instructions

Here you determine whether or not to activate the strobe alarm, and if activated, whether to activate the strobe until

the alarm system is disarmed, or, for the programmed period of time (see "Siren Configuration" section in the

control panel Installer Guide).

Optional settings: Timer limited (default), Disabled and Until Disarmed

Here you determine whether or not to activate the exit – entry beeps, and if enabled, whether to activate in HOME or

AWAY mode.

Optional settings: Disabled (default), Disabled & Home and Enabled.

Here you determine whether or not to enable the squawk, and if enabled, whether to activate the sounder only, or, the

sounder and strobe simultaneously.

Optional settings: Disabled (default), Sounder only, Strobe only and Sounder+strobe.

Here you determine the volume level of the sounder.

Optional settings: Volume HIGH(default), Volume LOW and Volume MID.

•

Here you determine whether or not the LED will be activated to indicate that the siren is operating.

Optional settings: Disabled (default) and Enabled.

•

Here you determine whether or not the siren alone will sound a tamper alarm when there is no communication

between the siren and the control panel.

Optional settings: Disabled (default) and Enabled.

. .

. LOCAL DIAGNOSTICS TE

LOCAL DIAGNOSTICS TELOCAL DIAGNOSTICS TE

LOCAL DIAGNOSTICS TEST

STST

Before testing, remove the plastic cover and then open the

battery cover (see Fig. 2).

A. Press the self-test button once and release it; the following

procedure should occur in turn:

The red LED will switch ON and then OFF, the green LED will

switch ON and then OFF, the strobe light will switch ON and

then OFF and the piezo siren will sound to indicate that the

siren is now fully operational.

B. After 2 seconds the LED blinks 3 times.

The following table indicates received signal strength

indication.

LED response Reception

Green LED blinks Strong

Orange LED blinks Good

Red LED blinks Poor

No blinks No communication

IMPORTANT! Reliable reception must be assured. Therefore,

"poor" signal strength is not acceptable. If you receive a "poor"

signal from the device, re-locate it and re-test until a "good" or

"strong" signal strength is received.

Note: For detailed Diagnostics Test instructions refer to the

control panel Installer Guide.

AUTO TAMPER ALRM

ACTIVITY LED

SOUNDER VOLUME

SQUAWK

EXIT-ENTRY Beeps

STROBE ALARM

DEVICE SETTINGS

SR1: DEV SETTINGS

SR1:P1 P2 P3

SR1:PARTITIONS

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Visonic SR-740 PG2 Seite 3

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info