Bedienungsanleitung Vitalmaxx BZ-0708 - Z04159 (Seite 4 von 8) (Deutsch, Englisch, Holländisch, Französisch)

703337

Zoom out

Zoom in

Vorherige Seite

1/8

Nächste Seite

EN Instructions

Customer Service / Importer:

DS Produkte GmbH, Am Heisterbusch 1, 19258 Gallin, Germany •

✆ +49 38851 314650 *)

*) Calls to German landlines are subject to charges. The cost varies depending on the service provider.

■ Before initial use you should test the device on your lower arm.

If there is no undesired skin reaction, you can use the device

on your face.

■ When using the device a tingling sensation and a skin redden-

ing is normal and should disappear within half an hour.

■ In order to avoid the formation of blotches, during the ap-

plication the attachment should be kept in constant motion

on the skin. You are recommended to stretch the skin on the

cheeks, for example, to avoid excessive suction.

■ Without pressing against the skin you move the device slowly

along a straight line, and not in circles!

PLEASE NOTE! If the device stops or cannot be switched on, the

battery needs charging.

While the device is running, the suction head is lit blue. The blue

light has an additional purifying function during acne treatment.

Three attachments are supplied:

• Round pore attachment for cleaning the pores, not suitable

for the skin around the eyes

• Oval attachment for stimulating the circulation of the skin

• Microcrystalline attachment for microdermabrasion: removal

of dead skin cells by friction and suction of the face, elbows,

knees etc.

Cleaning Pores

1. Remove make-up and clean your face in the usual way.

2. For optimum results, the pores should be opened before the

application. For this purpose you soak a small, clean ﬂ annel in

hot water, wring it out and place it on your face. As an alterna-

tive you can carefully place your face above a dish with hot

water, or use the device immediately after a shower or bath.

3. Next you pat your face dry.

4. Place the round pore attachment on the suction head.

5. Press the on / off button. The device switches on.

6. In order to remove sebum and blackheads, you place the at-

tachment against the skin (without pressure) and slowly move

it outwards from the centre in straight lines across the skin. Do

not move it backwards and forwards along the same line. Re-

peat if necessary. Any acne spots should be vacuumed brieﬂ y

before the attachment is removed again. Do not move side-

ways!

7. After the application you switch off the device, remove the at-

tachment and clean it.

8. Soak a cotton pad with facial lotion or the like and clean your

face. After that you apply a skin care product.

Microdermabrasion

1. Remove make-up and clean your face in the usual way. Then

dry it thoroughly.

2. Place the microcrystalline attachment on the suction head.

3. Press the on / off button. The device switches on.

4. Begin the facial treatment on the chin and proceed to the

forehead. Move the attachment slowly without pressure over

the skin. Move it outwards from the centre in straight lines.

Do not move it backwards and forwards along the same line.

NOTE: the microcrystalline attachment can be used on parts of

the body such as the elbows or knees.

5. After the application you switch off the device, remove the at-

tachment and clean it.

6. Apply a skin care product.

Stimulating the circulation of the skin

1. Remove make-up and clean your face in the usual way. Then

dry it thoroughly.

2. Place the oval attachment on the suction head.

3. Press the on / off button. The device switches on.

4. Any areas where wrinkles form (e.g. around the mouth) should

be vacuumed brieﬂ y before the attachment is removed again.

Do not repeat too often in one location – this could lead to

blotches!

5. After the application you switch off the device, remove the at-

tachment and clean it.

6. Apply a skin care product.

Cleaning and Care

NOTE

■ Do not use any corrosive or abrasive cleaning agents!

• After every use the attachments should be cleaned under run-

ning water. If necessary you can use a mild detergent and cot-

ton buds.

• Wipe down the device with a damp cloth if necessary and then

dry it with a soft cloth.

• Store the appliance away from dust and direct sunlight in a dry,

clean place that is not accessible to children and animals.

• If the attachments do not cling to the suction head, the silicone

ring is probably damaged and must be replaced. Replacement

silicone rings are supplied.

• If the ﬁ lter in the suction head is dirty, it should be replaced (see

below). Replacement ﬁ lters are supplied.

Changing the ﬁ lter

1. Pull the round silicone insert out of the suction head.

2. Use a sharp object (e.g. needle, tweezers) to remove the dirty

ﬁ lter from the suction head.

3. Separate a fresh ﬁ lter from the foil and place it into the suction

head.

4. Put the round silicone insert back into the suction head.

Technical Data

Article number: 04159

Model number: BZ-0708

Operating time: approx. 3 – 5 hours (when fully charged)

Charging time: 3 – 5 hours (with 5 V DC; 1 A)

Operating voltage: 3.7 V DC; (Li-polymer battery, 900 mAh)

Charging voltage/current: 5 V DC; 1 A

Power: max. 5 W

Light wavelength: 465 nm

Disposal

Dispose of the packaging in an environmentally

friendly manner and take it to a recycling centre.

Dispose of the device with the integrated battery at

a recycling centre for used electrical and electronic

devices, and not in the household waste. For more

information, contact your local authorities.

Article number: 04159

Z 04159 M DS V1 1017

Vitalmaxx BZ-0708 - Z04159 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info