Bedienungsanleitung Vivanco ur 2400 (Seite 4 von 88) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Portugiesisch, Spanisch, Polnisch, Türkisch, Schwedisch, Norwegisch, Finnisch)

122855

Zoom out

Zoom in

Vorherige Seite

1/88

Nächste Seite

of the code you want to read off.

For example, if you press +1 and the set

code is e.g. 1234, the lamp blinks once after

+1 is pressed to indicate that the thousends

figure is 1. All you have to do is to count. The

hundreds figure is indicated after pressing

+2, e.g. it blinks 2 times for the 2 in 1234. The

tens figure is indicated after +3 is pressed,

e.g. it blinks 3 times for the 3 in 1234. The

unit figure is indicated after +4 is pressed,

e.g. it blinks 4 times for the 4 in 1234.

- There will be no flash in case of 0 indication..

Learning of Missing Control Functions

(UR 2400 only)

The LEARN function is used to supplement the

preprogrammed codes. The standard code may

provide most of functions needed, but you may

miss some button functions. Or you didn´t find

any functioning preprogrammed code for a

device. You can capture upto 206 button func-

tion codes, max. 40 per device. The last cap-

tured function will overwrite the previous. learnt.

1 For learning of button codes you must use a

functioning original remote controller. Please

use fresh batteries for both remote controls.

2 Please point the original remote control trans-

mitter LED towards the receiver LED of UR

2400 (placed on top, same as transmitter

LED). Distance of LEDs between both re-

motes shall be approximately 1-2 cm and

must be in straight line of sight.

– Sometimes you have to move the remotes a

bit too and fro while learning, in order to find

right positions.

3 Press the LEARN button for about 3 seconds

until the LED (lamp) turns on.

4 Press SELECT button to select to be con-

trolled device as often until TV LED is on.

5 Press and release the target button on the

UR 2400, that you want to learn (reprogram)

(e.g. POWER), the LED starts flashing.

6 Press and hold the source button on the ori-

ginal remote control (e.g. POWER) until the

LED on your UR 2400 remote control stops

flashing and changes to on again. That indic-

ates that a new function code, e.g. POWER,

has been learnt.

7 Repeat steps 5 to 6 for capturing more button

functions.

8 Press and release LEARN button for exit of

learning mode.

– The controller will exit the learning mode auto-

matically after about 10 seconds of inactivity.

- Memory full indication: If the memory is full,

the LED flashes 2 times and then a pro-

grammed button can be overwritten.

Reset/deletion of a single learnt button func-

tion

1 Press LEARN button and then 1 button simul-

taneously until a device lamp (LED) lights

constantly.

2 Press SELECT button to select device, which

belongs to the to be deleted button function

as often until e.g. TV LED is on.

Vivanco GmbH, D-22926 Ahrensburg, E-Mail: hotline@vivanco.de, Helpline: +49 (0) 4102 231135

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vivanco ur 2400 Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info