Bedienungsanleitung Vonroc S_PM504AC (Seite 5 von 48) (Deutsch, Englisch, Holländisch, Dänisch, Französisch, Italienisch, Spanisch, Polnisch, Türkisch, Schwedisch)

778351

Zoom out

Zoom in

Vorherige Seite

1/48

Nächste Seite

WWW.VONROC.COM

of battery packs should only be performed by the

manufacturer or authorized service providers.

ADDITIONAL SAFETY WARNINGS FOR

POLISHERS

a) This power tool is intended to function as a

polisher. Read all safety warnings, instructions,

illustrations and speciﬁcations provided with

this power tool. Failure to follow all instructions

listed below may result in electric shock, ﬁre

and/or serious injury.

b) Operations such as grinding, sanding, wire

brushing, or cutting-off are not recommended

to be performed with this power tool. Operati-

ons for which the power tool was not designed

may create a hazard and cause personal injury.

c) Do not use accessories which are not speciﬁ-

cally designed and recommended by the tool

manufacturer. Just because the accessory

can be attached to your power tool, it does not

assure safe operation.

d) The rated speed of the accessory must be at

least equal to the maximum speed marked on

the power tool. Accessories running faster than

their rated speed can break and ﬂy apart.

e) The outside diameter and the thickness of your

accessory must be within the capacity rating of

your power tool. Incorrectly sized accessories

cannot be adequately guarded or controlled.

f) Threaded mounting of accessories must match

the grinder spindle thread. For accessories

mounted by ﬂanges, the arbour hole of the

accessory must ﬁt the locating diameter of

the ﬂange. Accessories that do not match the

mounting hardware of the power tool will run

out of balance, vibrate excessively and may

cause loss of control.

Do not use a damaged accessory. Before each

use inspect the accessory such as abrasive

wheels for chips and cracks, backing pad for

cracks, tear or excess wear, wire brush for loose

or cracked wires. If power tool or accessory is

dropped, inspect for damage or install an unda-

maged accessory. After inspecting and installing

an accessory, position yourself and bystanders

away from the plane of the rotating accessory

and run the power tool at maximum no-load

speed for one minute. Damaged accessories will

normally break apart during this test time.

h) Wear personal protective equipment. Depen-

ding on application, use face shield, safety

goggles or safety glasses. As appropriate,

wear dust mask, hearing protectors, gloves

and workshop apron capable of stopping small

abrasive or workpiece fragments. The eye

protection must be capable of stopping ﬂying

debris generated by various operations. The

dust mask or respirator must be capable of

ﬁltrating particles generated by your operation.

Prolonged exposure to high intensity noise may

cause hearing loss.

Keep bystanders a safe distance away from

work area. Anyone entering the work area must

wear personal protective equipment. Fragments

of workpiece or of a broken accessory may ﬂy

away and cause injury beyond immediate area

of operation.

j) Hold the power tool by insulated gripping surfa-

ces only, when performing an operation where

the cutting accessory may contact hidden

wiring or its own cord. Cutting accessory con-

tacting a “live” wire may make exposed metal

parts of the power tool “live” and could give the

operator an electric shock.

k) Position the cord clear of the spinning acces-

sory. If you lose control, the cord may be cut or

snagged and your hand or arm may be pulled

into the spinning accessory.

l) Never lay the power tool down until the acces-

sory has come to a complete stop. The spinning

accessory may grab the surface and pull the

power tool out of your control.

m) Do not run the power tool while carrying it at

your side. Accidental contact with the spinning

accessory could snag your clothing, pulling the

accessory into your body.

Regularly clean the power tool’s air vents. The

motor’s fan will draw the dust inside the housing

and excessive accumulation of powdered metal

may cause electrical hazards.

o) Do not operate the power tool near ﬂammable

materials. Sparks could ignite these materials.

p) Do not use accessories that require liquid cool-

ants. Using water or other liquid coolants may

result in electrocution or shock.

q) Do not allow any loose portion of the polishing

bonnet or its attachment strings to spin freely.

Tuck away or trim any loose attachment strings.

Loose and spinning attachment strings can

entangle your ﬁngers or snag on the workpiece.

Do not press the spindle lock until the tool stops.

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Vonroc S_PM504AC Seite 5

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info