809775

VTech DM1211 Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Parent unit overview
1Visual sound indicator
The visual sound indicator shows the
sound level detected by the baby unit.
• One to three green
lights indicate a moderate sound level
detected by the baby unit.
• Additional red lights
indicate a higher sound level detected
by the baby unit (e.g. baby crying
loudly).
2LCD display
3Microphone
1Night light
• On when night light is turned on
manually.
• Off when night light is turned off
manually.
2
• Press to turn the night light on or off.
3
• Press to decrease the speaker
volume.
4(On/off)
• Press to power on, and the power
light turns on.
• Press and hold to power off, and the
power light turns off.
5
• Press to increase the speaker
volume.
6Microphone
7POWER light
• On when the baby unit is turned on.
8PAGE
• Press to start or stop paging parent
unit.
9Power jack
10 Speaker
11 Temperature sensor
• The parent unit beeps when the
detected temperature is at the alert
temperature values.
Low limit value is 20oC and high limit
value is 30oC.
2. Press or to choose BABY VOLUME,
then press SELECT.
3. Press or to choose the desired
volume level, then press SELECT to confirm
your selection. The screen displays SAVED
and you hear a confirmation tone.
NOTE
• The speaker of baby unit cannot be muted.
Adjust the speaker volume for parent unit
You can adjust the speaker volume from
VOLUME 1 to VOLUME 5, or turn it off. The
speaker volume is preset to VOLUME 3.
• Press or when the parent unit is not
in use.
When the speaker volume is set to VOLUME
OFF, the screen displays .
Set default
Use this feature to restore to the default
settings.
1. Press MENU when the parent unit is not in
use.
2. Press or to choose RESET, then
press SELECT.
3. Press SELECT again to choose
CONFIRM?.
Vibration alert
You can set your parent unit to vibrate and
alert you, whenever the baby unit detects loud
sounds. This feature is preset to OFF.
Once this feature is on, is shown on LCD
display. When the visual sound indicator hits the
red light range, i.e. the baby unit detects loud
sounds, your parent unit vibrates and flashes.
1. Press MENU when the parent unit is not in
use.
2. Press or to choose VIBRATOR,
then press SELECT.
3. Press or to choose ON? or OFF?.
4. Press SELECT to confirm your selection.
The screen displays SAVED and you hear a
confirmation tone.
NOTES
• Each time you set the vibration alert to ON?,
the parent unit vibrates briefly after you press
SELECT.
Install the battery as shown below.
The parent unit runs on rechargeable battery or
AC power. To continuously monitor your baby,
make sure you use both battery and AC power
at the same time. With the battery alone, the
parent unit can cordlessly run for a short time
only.
NOTES
• Use only the battery supplied with this product.
• If the parent unit will not be used for a long time,
disconnect and remove the battery to prevent
possible leakage.
Install the battery
Replace the battery
To replace the battery, unplug the battery
connector from the socket, and then pull the
battery out of the battery compartment. Follow
the steps above to install the battery.
Charge the parent unit battery
When you have connected the parent unit and
installed its battery for the first time, it powers
on automatically. The battery icon indicates the
battery status (see the following table).
NOTES
• The parent unit battery is fully charged after
16 hours of continuous charging.
• It takes longer to charge the battery when the
parent unit is turned on. To shorten the charging
time, turn the parent unit off while charging.
• The standby time varies depending on the
sensitivity level you set, your actual use, and the
age of the battery.
Battery
indicators
Battery
status
Action
The battery
icon is off.
No battery is
installed but
operates using
AC power.
Install the
parent unit
battery.
Charge without
interruption
(at least 30
minutes).
The screen
displays
LOW
BATTERY
and .
The
light
flashes.
The battery
has very little
charge and
may be used
for only a short
time.
Charge
without
interruption
(about 30
minutes).
The battery
icon
becomes
solid .
The battery is
fully charged.
To keep
the battery
charged,
connect it to
power socket
when not in
use.
NOTES
• This baby monitor should be for use by adults
only.
• It is not a substitute for proper adult supervision,
and should not be used as such.
Test your audio monitor
You may test the baby monitor before initial use,
and at regular times thereafter.
CAUTION
• For hearing protection, make sure the
parent unit is more than 6.5 feet (2 metres)
away from the baby unit. If you hear any
feedback, move the parent unit further until
the noise stops. You can also press on
the parent unit to lower or mute the noise.
1. Make sure your baby unit and parent unit
are on.
2. Speak towards the microphone of the baby
unit. You will hear the sound at the parent
unit, and see the visual sound indicators
light up.
NOTE
• When the parent unit displays NOT LINKED and
flashes, move the parent unit closer to the baby
unit (observe the minimum distance of 6.5 feet/
2 metres). You can also check if the baby monitor
is connected to a live power socket and switched
on.
TIP
• Increase the speaker volume of the parent unit if
you cannot hear the sounds transmitted from the
baby unit.
Before use
Baby unit overview
Overview
What’s in the box
Connect the baby monitor
NOTES
• Use only the power adaptors supplied with this
product.
• Make sure the electrical outlets are not controlled
by wall switches.
• The power adaptors are intended to be correctly
oriented in a vertical or floor mount position. The
prongs are not designed to hold the plug in place if
it is plugged into a ceiling, under-the-table or cabinet
outlet.
• Make sure the parent unit, the baby unit and the
power adaptor cords are out of reach of children.
Connect and charge the
battery
Power on or off the baby unit
• Press to power on the baby unit. The
power light turns on.
• Press and hold to power off the baby unit.
The power light turns off.
Power on or off the parent unit
• Press and hold to power on the parent
unit. The screen turns on.
• Press and hold again to power off the
parent unit. The screen turns off.
NOTE
• The parent unit powers on automatically once it
is connected to power socket or battery installed.
The baby unit also powers on automatically once
connected to power socket.
Adjust the speaker volume for baby unit
• Press or on the baby unit at any
time.
Adjust the speaker volume for baby unit
using parent unit
You can also adjust baby unit’s speaker volume
in the parent unit. Level 1 is the softest while
Level 5 is the loudest.
1. Press MENU when the parent unit is not in
use.
Using the baby monitor
Congratulations
on purchasing your new VTech product. Before
using this product, please read
Important safety instructions.
This manual has all the feature operations and
troubleshooting necessary to install and operate
your new VTech product. Please review this
manual thoroughly to ensure proper installation
and operation of this innovative and feature rich
VTech product.
Positioning the baby monitor
CAUTIONS
• Keep the baby unit out of the reach of the baby.
Never place or mount the baby unit inside the
baby’s cot or playpen.
1. Place the baby unit more than 3 feet
(1 metre) away from your baby.
2. Bend down the temperature sensor so that it
stays away from baby unit to avoid deviation
of temperature detection.
3. Place the parent unit more than 6.5 feet
(2 metres) away from the baby unit.
CAUTION
• The default volume of your parent unit is level 3. If
you experience feedback from your baby monitor
while positioning:
- Make sure your baby unit and parent unit are
more than 6.5 feet (2 metres) apart, OR
- Turn down the volume of your parent unit.
5
5
LINKED
25 C
2 metres
>
o
25 C
o
5
5
5
5
5
5
5
> 1 metre
5
LINKED
LINKED
> 2 metres
2 metres
<
DM1211
Digital Audio Monitor
User’s manual
Parent unit status icons
Connection status
• displays when strong signal
strength is detected between the
baby unit and the parent unit.
• displays when moderate signal
strength is detected between the
baby unit and the parent unit.
• displays when the weak signal
strength is detected between the
baby unit and the parent unit.
• flashes when the link between the
baby unit and the parent unit is lost.
Night light
• On when the night light is turned on.
Lullaby
• Displays when the baby unit is
playing lullaby.
Sound alert
• Displays when the sound alert of the
parent unit is turned on.
• Flashes when there are loud sounds
detected from the baby unit.
Vibration alert
• Displays when the vibration alert of
the parent unit is turned on.
• Flashes when there are loud sounds
detected from the baby unit.
Volume off
• Displays when the patient unit
speaker volume is turned off.
Battery status
• animates when
the battery is charging.
• displays solid when the battery is
fully charged.
• flashes when the battery is in low
level and needs charging.
• No battery icon displays when there
is no battery installed.
4
• Press to decrease the speaker
volume.
• Press repeatedly until the volume
reaches the minimum to turn it off.
• While in a menu, press to scroll down.
5MENU
• Press to enter the menu.
• While in a menu, press to return to the
previous menu.
6Speaker
7 Battery LED
• Light on when the battery is being
charged.
• Light flashes when the battery is low
and needs charging.
• Light off when the parent unit is
running on AC power without battery
installed, or the parent unit is running
on battery only.
8
• Press to increase the speaker volume.
• While in a menu, press to scroll up.
9SELECT
• While in a menu, press to choose an
item, or save a setting.
10 (On/off)
• Press and hold to power on, the
screen turns on.
• Press and hold again to power off, the
screen turns off.
• While in a menu, press to return to
idle screen.
11 TALK
• Press and hold to talk to the baby.
12 Power jack
13 Belt clip
14 Battery compartment cover
Parent unit display screen
messages
LOW
BATTERY
• The parent unit uses only
the rechargeable battery
pack and it needs to be
recharged.
NOT
LINKED
• The link between the parent
unit and the baby unit is lost
continuously for over 10
seconds.
PAGING • The parent unit is being
paged by the baby unit.
SAVED • Your selection has been
saved.
TALK • You are using the parent unit
to talk to your baby.
o
C• Displays the real-time
temperature detected by the
baby unit in Celsius (oC)
(e.g. 22 oC).
5
Operating range
The operating range of the baby monitor is
up to 1,500 feet (450 metres) outdoors or 160
feet (50 metres) indoors. The actual operating
range may vary depending on the environmental
conditions, and other interferences such as
walls, doors, and other obstructions.
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für VTech DM1211 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von VTech DM1211

VTech DM1211 Bedienungsanleitung - Deutsch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info