Bedienungsanleitung VTech RM5754HD (Seite 2 von 2) (Englisch)

809798

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

mount the baby unit (optional)

1. Place the wall mount bracket on a

wall and then use a pencil to mark

two holes in parallel. Remove the

wall mount bracket and drill two

holes in the wall (5.5mm drill bit).

Notes

Check for reception strength and camera

angle of the baby unit before drilling the

holes.

• The types of screws and wall plugs you

need depend on the composition of

the wall. You may need to purchase

the screws and wall plugs separately to

mount your baby units.

2. If you drill the holes into a stud, go

to step 3.

• If you drill the holes into an

object other than a stud, insert

the wall plugs into the holes.

Tap gently on the ends with a

hammer until the wall plugs are

ﬂush with the wall.

3. Align the wall mount bracket and screws with

the holes in the wall as shown. Tighten the screw

in the middle hole ﬁrst, so that the wall mount

bracket position is ﬁxed. You can tighten the

other screw in the top hole.

3. Insert the screws into the holes and

tighten the screws until only 6mm of the

screws are exposed.

4. Place the baby unit on the wall

mount bracket, and then slide it

forward until it locks into place. Align

the holes on the wall mount bracket

with the screws on the wall, and slide

the wall mount bracket down until it

locks into place.

5. You can maximise your baby unit viewing angles by tilting the wall mount bracket.

Hold the baby unit, and then rotate the knob in an anticlockwise direction. This will loosen the joint of the wall mount bracket.

Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in a clockwise direction to tighten the

joint and secure the angle.

4. Place the baby unit on the wall mount bracket,

and then slide it forward until it locks into place.

Connect the power adaptor to the baby unit

and a power supply.

Download app for mobile access

Test the sound level and position the HD video monitor

Basic operation

Auto software and rmware update

If you plan to install your baby unit in a designated

location, and use your home Wi-Fi network to

connect your video monitor, you need to test

which of your selected monitoring areas within the

house have good Wi-Fi signal strength. After you

have powered on your parent unit, you can use

your parent unit’s Wi-Fi signal strength indicator

to assist in checking. Once you have identiﬁed the

suitable location, you can install your baby unit.

Adjust the distance between your baby unit and

the Wi-Fi router if needed.

• Depending on surroundings and obstructing

factors that affect signal strength, such as distance

and internal walls, you may experience reduced

Wi-Fi signal. To improve the Wi-Fi signal strength,

adjust the distance or direction of your parent unit.

Check with your parent unit again.

test the location for the baby unit

Talk to your baby via the baby unit

1. Press and hold the TALK key.

2. When the icon displays on

screen, speak to your parent unit.

Your voice is transmitted to the

baby unit.

3. When ﬁnished talking, release

the TALK key and hear your baby

again.

Zoom

Press to zoom in or out.

Adjust speaker volume

Press -VOL / VOL+ to adjust your parent unit

speaker volume level received from the baby

unit.

After powering up your video monitor, the parent unit streams live video in direct mode.

We recommend you follow the instructions on screen to set up home Wi-Fi network

with your monitor for functionality enhancements and mobile access. See Auto software

and rmware update and Download app for mobile access in this quick start guide.

Use the menu

Press MENU on the parent unit to enter the

main menu, choose a menu item, or save a

setting. You can use the parent unit menu for

advanced settings or operations, such as to

play or stop lullaby, or adjust the motion and

sound detection settings.

While in the menu:

• Press , , or to scroll among the

menu options.

• Press SELECT to select an item.

• Press TALK / to return to the live video.

• Press to go to the Help & info page.

You can reset the parent unit by pressing the

RESET key at the back of the unit.

Use a pin and insert it into the hole on the

back of the parent unit, and then press the

button inside.

Turn on/off the parent unit screen

Turn on or off the parent unit screen without

powering off the parent unit. You will still

hear sounds from the baby unit.

• Press POWER on the parent unit to turn

off the screen.

• Press any key on the parent unit to turn

the screen on again.

Notes

• This baby monitor should be for use by adults only.

• It is not a substitute for proper adult supervision, and should not be used as such.

Testing the sound level of the HD video monitor

• For hearing protection, make sure the parent unit is more than 1 metre away from the baby

unit. If you hear a feedback from the parent unit, move the parent unit further away until the

noise stops. You can also press - VOL on the parent unit to lower or mute the noise.

• Increase the parent unit speaker volume if you cannot hear the sounds transmitted from the

baby unit.

Positioning the HD video monitor

• Keep the baby unit out of the reach of your baby. Never

place or mount the baby unit inside the baby’s cot or

playpen.

1. Place the baby unit more than 1 metre away from

your baby.

2. Adjust the angle of the baby unit to aim at your baby.

3. To avoid causing a feedback from your HD video monitor:

• Make sure your baby unit and parent unit are more than 1 metre apart; OR

• Turn down the volume of your parent unit.

> 3ft (1m)

> 1 metre > 1 metre

Speciﬁcations are subject to change without notice.

Technical specications

Frequency control Crystal controlled PLL synthesizer

Transmit frequency Baby unit: 2412 - 2472 MHz

Parent unit: 2412 - 2472 MHz

Maximum power used by the transmitter: 0.1W (100mW)

Channels 13

LCD 5” Colour LCD (IPS 1280x720 pixels)

Nominal effective

range

Actual operating range may vary according to environmental

conditions at the time of use.

Power requirements Parent unit: 3.8V 2100mAh Li-ion battery

Baby unit power adaptor:

Output: 5V DC @ 1A

Parent unit power adaptor:

Output: 5V DC @ 1A

Disposal of batteries and product

The crossed-out wheelie bin symbols on products and batteries, or on their respective

packaging, indicates they must not be disposed of in domestic waste as they contain

substances that can be damaging to the environment and human health.

The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains

more than the speciﬁed value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in

Battery Directive (2006/66/EC).

The solid bar indicates that the product was placed on the market after 13th August, 2005.

Help protect the environment by disposing of your product or batteries responsibly.

Credits:

The Background Noise sound ﬁle was created by Caroline Ford, and is used under the Creative Commons license.

The Stream Noise sound ﬁle was created by Caroline Ford, and is used under the Creative Commons license.

The Crickets At Night sound ﬁle was created by Mike Koenig, and is used under the Creative Commons license.

The Heart Beat sound ﬁle was created by Zarabadeu, and is used under the Creative Commons license.

Customer service and product warranty

Android TM and Google Play TM are trademarks of Google Inc.

App Store is a trademark of Apple Inc., registered in the U.S. and other countries.

iOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license.

Manufacturer: VTech Telecommunications Ltd.

23/F., Tai Ping Industrial Centre, Block 1, 57 Ting Kok Road, Tai Po, Hong Kong.

Importer: VTech Electronics Europe Plc.

Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT.

IMPORTANT

Please retain this booklet with your sales receipt as proof of the date of purchase.

Customer Service

Please visit www.vtechphones.eu to contact our Customer Service Department.

Declaration of Conformity

This product is intended for use within Europe and UK.

This equipment complies with the essential requirements to EU’s Radio Equipment Directive

(2014/53/EU) and the UK’s Radio Regulations 2017 on radio systems and telecommunication

equipment.

VTech Telecommunications Ltd. hereby declares that this 5” Smart Wi-Fi 1080p Video Monitor

RM5754HD is in compliance with the essential requirements and other relevant provisions of EU’s

Radio Equipment Directive (2014/53/EU) and UK’s Radio Equipment Regulations 2017.

The Declaration of Conformity for the RM5754HD is available from

www.vtechphones.eu.

10:25 AM

Muted

10:25 AM

Press and hold

> 10ft (3m)

10:25 AM

> 1 metre> 1 metre

< 10ft (3m)

> 10ft (3m)

> 1 metre> 1 metre

< 1 metre< 1 metre

To keep this product working well and looking good, follow these guidelines:

• Avoid placing it near heating appliances and devices that generate electrical noise (for example,

motors or ﬂuorescent lamps).

• DO NOT expose it to direct sunlight or moisture.

• Avoid dropping the product or treating it roughly.

• Clean with a soft damp cloth.

• DO NOT immerse the parent unit and the baby unit in water and do not clean them under running

water.

• DO NOT use cleaning spray or liquid cleaners.

• Make sure the parent unit and the baby unit are dry before you connect them to the mains again.

• Clean the USB charging port of dust, dirt, and lint regularly.

General product care

If the HD video monitor will not be used for an extended period of time, store the parent unit, the baby

unit, and the adaptors in a cool, dry place.

Storage

This warranty is valid for the UK and Ireland only. For products purchased outside

the UK and Ireland, please contact your local distributor or place of purchase.

ONE

YEAR

PRODUCT WARRANTY

Thank you for choosing this quality product from VTech.

1.The product detailed above is covered by a one year warranty from the date of purchase,

against any defects in materials or workmanship.

2.The product may be returned to the place of purchase. Alternatively the product can be

returned to VTech Electronics Europe Plc (see address below), with proof of purchase,

without proof of purchase no replacement will be provided.

3.VTech Electronics Europe Plc will examine the product and if it is found to be defective

due to faulty materials or workmanship, will replace the product at their discretion.

4.If the product covered by this warranty is damaged due to misuse, modification or

unauthorized repair, or because of faulty batteries, battery discharge or incorrect

electrical connections, then this warranty becomes void.

5.This warranty is personal to the original purchaser and is not transferable.

6.Breakages to the LCD screen are not covered by the warranty.

7.Products returned to VTech Electronics Europe Plc, should be sent to the address shown

below and packed carefully to avoid damage in transit. Please do not include batteries or

adaptors. Please include details of the fault together with your name and address,

contact phone number and/or email address.

8.To keep an online record of your warranty, please register your product online at

www.vtech.co.uk/clubvtech

VTech Electronics Europe Plc, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane,

West Hallam, DE7 6HE

THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT

CONSUMERS’ STATUTORY RIGHTS.

PRODUCT REGISTRATION

Visit www.vtech.co.uk/clubvtech/login

to register your VTech product

By joining the VTech Club you can also enter competitions,

find out about news and events, seek expert advice for parents

and let your kids play fun learning games and activities.

To ensure that your HD video monitor is always at its best performance, the Parent Unit

will prompt a message and ask you to update its software and the Baby Unit’s ﬁrmware

when there are new versions available. Select “Now” to reboot the system, or switch off

and on the Parent Unit later to reboot the system into the latest software.

• To check if your device is running on the latest software, or to update your device

software, go to:

> Software Update.

Connect your HD video monitor with home Wi-Fi network

• You must connect your video monitor to your secured home Wi-Fi network in order

to receive the latest software and ﬁrmware updates. To set the Wi-Fi up, go to:

> Congure Wi-Fi.

Note

• Make sure the Baby Unit is on when you set up the Wi-Fi network.

Adjust baby unit speaker volume

1. Press MENU.

2. Go to Baby unit settings .

3. Press to scroll to Volume .

4. Press to decrease and to increase the baby unit’s

speaker volume.

Install MyVTech Baby Pro mobile app

1. Browse the App Store or the Google Play store .

2. Search for the mobile app with the keyword “MyVTech Baby Pro“.

3. Download and install the MyVTech Baby Pro mobile app to your mobile device.

Scan the QR code on the right to get the app.

Note

• Make sure your mobile device meets the

minimum requirement for the mobile app.

Minimum requirement

The mobile app is compatible with:

• AndroidTM 6.0 or later; and

• iOS 12.0 or later.

You can download the free MyVTech Baby Pro mobile app and install it

to a mobile device, then use your mobile device and the mobile app to

monitor your areas remotely.

1. Press MENU when the parent unit is idle.

2. Go to > Connect Mobile Phone.

3. Scan the QR code in the parent unit to download the app into your

mobile device.

4. Follow the instructions in the mobile app to set up and pair your baby

unit to the mobile app.

Alternatively, you can download the mobile app from the App Store or

Google Play store.

After installing the mobile app, follow the instructions in the mobile app and parent

unit to set up and pair your baby unit.

In your mobile device:

1. Tap to run the mobile app in your mobile device, and then create a user account.

2. We recommend that you use common webmail services, such as Google Gmail, for the

registration of your user account. Check your email (and Spam folder), and activate your

new user account via the email link. Then, sign in to your account.

3. Follow the instructions in the mobile app to pair the camera. Tap , then Add Camera

in the mobile app to get started.

VTech RM5754HD Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von VTech RM5754HD

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info