698342

VTech VM2251-2 Anleitung

1
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Note
• This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be used as such.
Test your baby monitor
You may test the baby monitor before initial use, and at regular times thereafter.
Caution
• For hearing protection, make sure the parent unit is
more than 3 feet (1 meter) away from both baby units. If
you hear any high-pitched noise, move the parent unit
further until the noise stops. You can also press VOL on
the parent unit to reduce the noise.
1. Make sure your baby unit and parent unit are on.
2. The parent unit displays images from the baby unit.
• Speak towards the microphone of the baby unit. You will hear the sound at the parent unit.
3. If you have two baby units, view the image from one of them by switching cameras via
menu. Then, repeat step 2.
Note
• When the parent unit displays No link to Camera, and the POWER LED light flashes, move the parent
unit closer to the baby units (observe the minimum distance of 3 feet / 1 meter). You can also check if
the baby unit is connected to a live power socket and switched on.
Tip
• Increase the speaker volume of the parent unit if you cannot hear the sounds transmitted from the baby units.
Positioning the baby monitor
Caution
• Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the baby’s crib or playpen.
Note
• To avoid interference from other electronic devices, place
your baby monitor far away from devices such as wireless
routers, microwaves, cell phones and computers.
1. Place the baby units more than 3 feet (1 meter)
away from your baby.
2. Adjust the angle of the baby unit camera to aim at
your baby.
3. Place the parent unit more than 3 feet (1 meter)
away from the baby units.
Caution
• The default volume of your parent unit is level 3, and the
maximum volume is level 5. If you experience high-pitched
screeching noise from your baby monitor while positioning:
- Make sure your baby units and parent unit are more than
3 feet (1 meter) apart, OR
- Turn down the volume of your parent unit.
Operating range
The operating range of the baby monitor is up to 1000 feet (300 meters) outdoors or 160 feet
(50 meters) indoors. The actual operating range may vary depending on the environmental
conditions and other interferences such as walls, doors and other obstructions.
Power on or off the baby unit
• Slide the ON/OFF switch to ON to turn on the baby unit. The POWER LED light turns on.
• Slide the ON/OFF switch to OFF to turn off the baby unit. The POWER LED light turns off.
Power on or off the parent unit
• Slide the ON/OFF switch to ON to turn on the parent unit. The screen and the POWER LED
light turns on.
• Slide the ON/OFF switch to OFF to turn off the parent unit. The screen and the POWER
LED light turns off.
Adjust parent unit speaker volume
• Press VOL /VOL on the parent unit to adjust the speaker volume.
Adjust LCD brightness
You can change the brightness of the parent unit screen from Level 1 to Level 5. The LCD
brightness is preset to Level 3.
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose the desired level of brightness, then press to confirm your selection.
Monitoring mode
*
for VM2251-2 only
Every time the parent unit is turned on, it displays a baby unit in SINGLE-CAM mode. If there
are more two baby units in your system, you can also monitor your baby in PATROL mode.
SINGLE-CAM The screen displays image of a single baby unit in full screen.
PATROL A single cam view that transitions to a different baby unit every 10 seconds.
To switch from SINGLE-CAM to PATROL mode:
1. Press when the parent unit is idle.
2. Press or to choose , then press or to open the submenu.
3. Press or to select to enter PATROL mode to alternately view the image from one
baby unit to the next one in every 10 seconds.
To switch from PATROL to SINGLE-CAM mode:
1. Press when the parent unit is idle.
2. Press or to choose , then press or to open the submenu.
3. Press or to select a camera number to enter SINGLE-CAM mode.
Note
• If one or more paired baby units are powered off or disconnected during patrolling, the parent unit
will keep searching until its power has run out or a baby unit is connected once again.
1 Pair hole
• Your baby units and parent unit
provided are already paired.
2 POWER LED light
• On when the baby unit is turned on
and is paired to the parent unit.
• Flashes when the baby unit is not
being viewed;
or when the link to the parent unit is
lost.
3 Microphone
4 Camera
5 Infrared LEDs
6 Light sensor
7
ON/OFF switch
• Slide to turn on or off the baby unit.
8 Speaker
9 Power jack
10 Wall mount holes
NOTESNOTE
• The rechargeable battery is pre-installed in your parent unit.
• Use only the power adapters supplied with this product.
• Make sure the baby monitor is not connected to the switch controlled electric outlet.
• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not
designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-the-table,
or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets.
• Make sure the parent unit, the baby unit and the power adapt\er cords are out of reach of children.
Connect the baby monitor
Charge the parent unit battery
When you have connected and turned on the parent unit, the battery will be charged
automatically. The battery icon indicates the battery status (see the following table).
NOTESNOTE
Notes
• The parent unit battery is fully charged after 11 hours of continuous charging.
• It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time,
turn the parent unit off while charging.
• The standby time varies depending on the volume level you set and your actual use.
Battery indicators Battery status Action
The screen displays Battery
low at Parent Unit. The
or light flashes.
The battery has very little
charge and may be used
for only a short time.
Charge
without interruption
(about 30 minutes).
The battery icon becomes
solid .
The battery is fully
charged.
To keep the battery charged,
connect it to AC power when
not in use.
User’s manual
VM2251
VM2251-2
Video Monitor
Go to www.vtechphones.com
to register your product for
enhanced warranty support and
the latest VTech product news.
Congratulations
on purchasing your new VTech product. Before using this product, please read Important safety
instructions.
This manual has all the feature operations and troubleshooting necessary to install and operate
your new VTech product. Please review this manual thoroughly to ensure proper installation and
operation of this innovative and feature-rich VTech product.
For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com.
1 set for VM2251
2 sets for VM2251-2
Screen off timer
You can set the screen off time for the parent unit when there is no key press for a specific time interval.
When the screen is turned off, you can still hear sound from the baby unit.
1. Press when the parent unit is idle.
2. Press or to choose , then press or to open the submenu.
3. Press or to choose the desired time period to automatically turn off screen
( / - 5 min./ - 30 min. / - 60min.), then press to confirm your selection.
Adjust the sound sensitivity of the baby unit
You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed
a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby
unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds for
transmitting to the parent unit. The VOX sensitivity level is preset to the highest level (Level 5).
VOX
Sensitivity
level
Level 5 Level 4 Level 3 Level 2 Level 1
Sensitivity
Highest VOX
sensitivity level
High VOX
sensitivity level
Medium VOX
sensitivity level
Low VOX
sensitivity level
Lowest VOX
sensitivity level
Description
The parent
unit speaker is
constantly on,
and you will
hear all sounds
(including
background
noises) from
your baby’s
room.
The parent
unit speaker
turns on for
soft babbling
and louder
sounds from
your baby. It
remains quiet
when your
baby sleeps
soundly.
The parent
unit speaker
turns on for
loud babbling
and louder
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
The parent unit
speaker turns
on for crying
and louder
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
The parent
unit speaker
turns on for
loud crying
or screeching
sounds from
your baby. It
remains quiet
when your
baby makes
soft sounds.
1. Press when the parent unit is idle.
2. Press or to choose , then press or to open the submenu.
3. Press or to choose the desired sensitivity level, then press to confirm your selection.
NOTESNOTE
Note
• If the screen is off, and the setting of sound-activated screen is ON, then LCD screen will be turned on
automatically when VOX sensitivity is triggered.
Tip
• If you want to use a sound machine or white noise machine for natural white noise while using this baby
monitor to check on your baby, you can:
- Lower the volume of your sound machine or white noise machine; or
- Lower the sensitivity level of your baby monitor to medium (level 3) or below. Default level is the highest level.
Turn on or off the sound activation
When sound activation is on, as long as no sound is detected within 50 seconds, the parent unit
screen will turn off automatically to save power.
When your baby unit detects a sound, which exceeds the selected sensitivity level, the sound
activation triggers the parent unit screen to turn on automatically. When no sound is detected
within 50 seconds, the screen will be off again.
1. Press when the parent unit is idle.
2. Press or to choose , then press or to open the submenu.
3. Press or to choose or , then press to confirm your selection.
Note
• If the sound sensitivity is set to the highest level, the parent unit screen may remain on continuously
even though sound activation is on. This depends on whether the baby unit detects any sounds.
Zoom
You can zoom in while viewing images from the baby unit.
• Press to zoom in. Press again to zoom out.
• Press , , or to move the zoomed image downward, upward, leftward or rightward.
Talk
You can use the TALK function of the parent unit to comfort your baby.
Press and hold TALK on the parent unit.
1. Speak towards the microphone on the parent unit. Your voice is broadcast to the baby unit.
2. Release the TALK key to stop the broadcast.
Monitor the temperature
Your baby unit monitors the temperature of your baby’s room with its built-in temperature
sensor. If the detected temperature is out of the preset temperature range, the parent unit
will display an alert message.
Set temperature range
You can set the desired minimum and maximum room temperature alert ranges.
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press .
4. Press or to choose or , then press .
5. Press or to choose the desired minimum or maximum temperature, then press to
confirm your selection.
Temperature alert tone
You can turn on the temperature alert tone so that the parent unit will emit an alert tone if the
detected temperature is out of range.
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press .
4. Press or to choose or , then press to confirm your selection.
Temperature format
You can choose to display the temperature in Fahrenheit (
o
F) or Celsius (
o
C).
1. Press when the parent unit is idle.
2. Press or to choose , then press .
3. Press or to choose , then press .
4. Press or to choose or , then press to confirm your selection.
1
Connect and charge the battery
What’s in the box
2
Before use
3
Using the baby monitor
Baby unit overview
3
Using the baby monitor (Con’t)
Frequency control Crystal controlled PLL synthesizer
Transmit frequency Baby unit: 2407.5 - 2475 MHz
Parent unit: 2407.5 - 2475 MHz
Channels 21
LCD 2.4” Color LCD
(QVGA 320x240 pixel)
Nominal effective range Maximum power allowed by FCC and IC. Actual operating range
may vary according to environmental conditions at the time of use.
Power requirements Parent unit: 3.6V Ni-MH battery
Baby unit power adapter: Output: 6V DC @ 400mA
Parent unit power adapter: Output: 6V DC @ 400mA
Technical specifications
Specifications are subject to change without notice.
© 2018 VTech Communications, Inc.
All rights reserved. 11/18. VM2251-X_CIB_V4
Document order number: 91-010824-050-100
>
3 ft (1m)
Parent unit overview
1 POWER LED light
• Green when the parent is powered
on.
• Flashes green when no link to
camera.
2 TALK
• Press and hold to talk to the selected
baby unit.
2
3
4
7
8
9
5
6
1
10
13
12
11
2
3
4
7
8
9
5
6
1
10
13
12
11
10
1
3
4
5
6
2
7
8
9
＜3ft (1m)
＞3ft (1m)
1
2
3
>
3ft (1m)
﹏﹏﹏
﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏
﹏﹏﹏
﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏
﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏
﹏﹏﹏﹏﹏
<
3ft (1m)
6
3ē
≥
<
3ft (1m)
3ft (1m)
63ē
63ē
≥
<
3ft (1m)
3ft (1m)
63ē
63ē
>
<
3ft (1m)
3ft (1m)
＜3ft (1m)
＞3ft (1m)
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für VTech VM2251-2 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info