809763

VTech VM5463 Seite 2

2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Night vision
The baby unit has infrared LEDs that
allow you to see your baby clearly at
night or in a dark room. When the baby
unit being viewed detects low light
levels, the infrared LEDs are switched
on automatically. The images from the
baby unit are in black and white, and
appears on the screen.
Notes
• It is normal if you see a short white glare
on your parent unit screen as the baby unit
adapts to the dark environment.
• When the infrared LEDs are on, the images
are in black and white. This is normal.
Tip
• Depending on the surroundings and other
interfering factors, like lightings, objects,
colours and backgrounds, the video quality
may vary. Adjust the baby unit angle or
place the baby unit at a higher level to
prevent glare and a blurry display.
Mount the baby unit on dry wall (optional)
Sound sensitivity and sound activation
Sound activated screen and audioAdjust sound detection sensitivity
When Sound activation is on, the parent unit screen remains
off to save power when the baby unit detects no sound.
Once the baby unit detects sounds that are louder than the
chosen sound sensitivity level, the parent unit screen and
speaker turn on automatically. The parent unit will then turn
off again after 50 seconds of no sound detection.
NOTESNOTE
Note
• If you have muted the parent unit speaker, only the parent unit
screen will turn on when a sound is detected.
You can turn on Sound activation and
adjust the VOX sensitivity to detect sounds
and turn on the parent unit while its screen
is switched off or dimmed.
When the baby unit detects sounds that
exceed certain levels, the parent unit
screen will turn on and the baby unit starts
transmitting the sounds to the parent unit,
and you can see and hear your baby. If you
have turned on the Night light Auto-on
and the Projection light Auto-on feature,
they will turn on automatically to sooth
your baby.
If you turn off Sound activation, you will
hear sounds from the baby unit all the
time, even when the parent unit screen is
switched off.
1. Place the wall mount bracket on a
wall and then use a pencil to mark
two holes in parallel. Remove the
wall mount bracket and drill two
holes in the wall (5.5mm drill bit).
NOTESNOTE
Notes
• Check for reception strength and
camera angle before drilling the holes.
• The types of screws and anchors you
need depend on the composition of
the wall. You may need to purchase the
screws and anchors separately to mount
your camera units.
2. If you drill the holes into a stud, go
to step 3.
• If you drill the holes into an
object other than a stud, insert
the wall anchors into the holes.
Tap gently on the ends with a
hammer until the wall anchors
are flush with the wall.
3. Align the wall mount bracket and screws with
the holes in the wall as shown. Tighten the screw
in the middle hole first, so that the wall mount
bracket position is fixed. You can tighten the
other screw in the top hole.
3. Insert the screws into the holes and
tighten the screws until only 6mm of the
screws are exposed.
4. Place the camera unit on the wall
mount bracket, and then slide it
forward until it locks into place. Align
the holes on the wall mount bracket
with the screws on the wall, and slide
the wall mount bracket down until it
locks into place.
5. You can maximize your camera unit viewing angles by tilting the wall mount bracket.
Hold the camera unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket.
Tilt your camera unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the
joint and secure the angle.
OR
4. Place the camera unit on the wall mount
bracket, and then slide it forward until
it locks into place. Connect the power
adapter to the camera unit and a power
supply not controlled by a wall switch.
2
1
Parent unit icons (Cont’d)
VOX
Sensitivity
level Level 5
(Highest)
Level 4
(High)
Level 3
(Medium)
Level 2
(Low)
Level 1
(Lowest)
Description (Default setting)
The parent unit
screen and
speaker turn
on for very
small sounds,
including
background
noises from your
baby’s room.
The parent
unit screen
and speaker
turn on for soft
babbling and
louder sounds
from your baby.
The parent unit
remains quiet
when your
baby sleeps
soundly.
The parent unit
screen and
speaker turns
on for loud
babbling and
louder sounds
from your baby.
The parent unit
remains quiet
when your
baby makes
soft sounds.
The parent
unit screen
and speaker
turn on
for crying
and louder
sounds from
your baby.
The parent
unit remains
quiet when
your baby
makes soft
sounds.
The parent
unit screen
and speaker
turn on for
loud crying
or screeching
sounds from
your baby.
The parent
unit remains
quiet when
your baby
makes soft
sounds.
Status icons
Connection status
• - Strong signal strength.
• - Moderate signal
strength.
• - Low signal strength.
• - Weak signal strength.
Current view status
• Displays camera when baby
unit successfully linked to
parent unit.
Night vision - On
Zoom - On
Lullaby - On
Night light - On
Night light - Auto-on
• Colour icon indicates the
night light is set to auto-on,
and is currently turned on by
sound activation.
• Gray icon indicates the night
light is currently off but is
set to auto-on. Night light
will turn on when sound is
detected by the baby unit.
Projection light - On
Projection light - Auto on
• Colour icon indicates the
projection light is set to auto-
on, and is currently turned on
by sound activation.
• Gray icon indicates the
projection light is currently
off but is set to auto-on.
Projection light will turn on
when sound is detected by
the baby unit.
Status icons
oF or
oCReal-time temperature
• Real-time temperature
detected by the baby unit in
Fahrenheit (oF) or Celsius (oC)
(e.g. 57
oF or 14
oC).
Temperature alert tone - On
9-level sound indicator
• indicates low sound level
detected by the baby unit.
• indicates moderate
sound level detected by the
baby unit.
• indicates high
sound level detected by the
baby unit.
Mute alert
• Displays when the parent
unit speaker volume is set
to off.
• Displays when the parent
unit is talking to the baby
unit.
Battery status
•
animates when the battery is
charging.
• - battery is fully
charged.
• - battery is low and
needs charging.
Speaker volume - displays the
parent unit speaker volume
level while adjusting.
Alert icons
• Displays when parent unit’s battery is low and needs charging.
• Displays when connection between parent unit and baby unit is lost.
• Baby unit detects temperature reaches or exceeds the set maximum.
• Baby unit detects temperature is at or is lower than the set minimum.
Dim mode helps you save parent unit power. Your parent unit display will dim
automatically after 10 minutes of inactivity, when no keys are pressed or alerts are
received from the baby unit.
Dim mode
10 min inactivity
Press any button
Optimal position
Projection light
Tip
• The projection light located on the top of the baby unit projects a starry soft night light scene onto
the ceiling with a tilting angle. Adjust your baby unit’s position with the projection light to help
sooth your baby to sleep. For optimal performance, place the baby unit in upright position.
To keep this product working well and looking good, follow these guidelines:
• Avoid placing it near heating appliances and devices that generate electrical noise (for example, motors or
fluorescent lamps).
• DO NOT expose it to direct sunlight or moisture.
• Avoid dropping the product or treating it roughly.
• Clean with a soft damp cloth.
• DO NOT immerse the parent unit and the baby unit in water and do not clean them under running water.
• DO NOT use cleaning spray or liquid cleaners.
• Make sure the baby unit and parent unit are dry before you connect them to the mains again.
General product care
When you are not going to use the baby monitor for some time, store the parent unit, the baby unit and the
adaptors in a cool and dry place.
Storage
Customer service and product warranty
The crossed-out wheelie bin symbols on products and batteries, or on their respective packaging,
indicates they must not be disposed of in domestic waste as they contain substances that can be
damaging to the environment and human health.
The chemical symbols Hg, Cd or Pb, where marked, indicate that the battery contains more than the
specified value of mercury (Hg), cadmium (Cd) or lead (Pn) set out in Battery Directive (2006/66/EC).
The solid bar indicates that the product was placed on the market after 13th August, 2005.
Help protect the environment by disposing of your product or batteries responsibly.
Disposal of batteries and product
Adult supervision
• This baby monitor should be for use by adults only.
• Do not place the baby unit inside the cot or playpen.
• To ensure your children’s safety, do not allow them to touch or play with the baby monitor and its
accessories. THIS IS NOT A TOY.
IMPORTANT
Please retain this booklet with your sales receipt as proof of the date of purchase.
Customer Service
Please call our Consumer Services Department on 03306 780149 (from UK) or
+44 3306 780149 (outside UK) and a service representative will be happy to help you.
Declaration of Conformity
This product is intended for use within Europe and UK.
This equipment complies with the essential requirements to EU’s Radio Equipment Directive
(2014/53/EU) and the UK’s Radio Regulations 2017 on radio systems and telecommunication
equipment.
VTech Telecommunications Ltd. hereby declares that
this Video Monitor VM5463 is in compliance with the essential requirements and other
relevant provisions of EU’s Radio Equipment Directive (2014/53/EU) and UK’s Radio Equipment
Regulations 2017.
The Declaration of Conformity for the VM5463 is available from
www.vtechbabycare.com.
Manufacturer: VTech Telecommunications Ltd.
23/F., Tai Ping Industrial Centre, Block 1, 57 Ting kok Road, Tai Po, Hong Kong.
Importer: VTech Electronics Europe Plc
Napier Court, Abingdon Science Park, Abingdon, Oxon, OX14 3YT, U.K.
This warranty is valid for the UK and Ireland only. For products purchased outside
the UK and Ireland, please contact your local distributor or place of purchase.
P
R
O
D
U
C
T
W
A
R
R
A
N
T
Y
ONE
YEAR
PRODUCT WARRANTY
Thank you for choosing this quality product from VTech.
1.The product detailed above is covered by a one year warranty from the date of purchase,
against any defects in materials or workmanship.
2.The product may be returned to the place of purchase. Alternatively the product can be
returned to VTech Electronics Europe Plc (see address below), with proof of purchase,
without proof of purchase no replacement will be provided.
3.VTech Electronics Europe Plc will examine the product and if it is found to be defective
due to faulty materials or workmanship, will replace the product at their discretion.
4.If the product covered by this warranty is damaged due to misuse, modification or
unauthorized repair, or because of faulty batteries, battery discharge or incorrect
electrical connections, then this warranty becomes void.
5.This warranty is personal to the original purchaser and is not transferable.
6.Breakages to the LCD screen are not covered by the warranty.
7.Products returned to VTech Electronics Europe Plc, should be sent to the address shown
below and packed carefully to avoid damage in transit. Please do not include batteries or
adaptors. Please include details of the fault together with your name and address,
contact phone number and/or email address.
8.To keep an online record of your warranty, please register your product online at
www.vtech.co.uk/clubvtech
VTech Electronics Europe Plc, c/o XPO Logistics, Warehouse 350, Cat & Fiddle Lane,
West Hallam, DE7 6HE
THIS WARRANTY IS OFFERED AS AN EXTRA BENEFIT AND DOES NOT AFFECT
CONSUMERS’ STATUTORY RIGHTS.
UK
PRODUCT REGISTRATION
Visit www.vtech.co.uk/clubvtech/login
to register your VTech product
By joining the VTech Club you can also enter competitions,
find out about news and events, seek expert advice for parents
and let your kids play fun learning games and activities.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für VTech VM5463 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von VTech VM5463

VTech VM5463 Bedienungsanleitung - Deutsch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info