Bedienungsanleitung Wave Ceptor 2554 (Seite 1 von 4) (Englisch)

120859

Zoom out

Zoom in

Vorherige Seite

1/4

Nächste Seite

USER’S GUIDE 2554

About This Manual

• Button operations are indicated using the letters shown

in the illustration.

• Each section of this manual provides you with the

information you need to perform operations in each

mode. Further details and technical information can be

found in the “Reference” section.

General Guide

• Press C to change from mode to mode.

• In any mode, press B to illuminate the display.

Date Alert Mode

Stopwatch Mode

Timekeeping Mode

Alarm Mode

▲

Press C.

▲

World Time Mode

Time Recorder Mode

▲

Current Time Setting

This watch automatically adjusts its time setting in accordance with a time calibration

signal. You can also perform a manual procedure to set the time and date, when

necessary.

• Before using the watch in Western Europe, first use the procedure under “Setting Up

the Watch for Use in Western Europe” to set the time in accordance with a time

calibration signal.

• Note that after you set your Home City (the city where you normally use the watch)

code, you must also turn on the watch’s time calibration signal receiver if you want to

enable auto time calibration. See “About Auto Receive” for more information.

• See “Setting the Time and Date Manually” for information about manual settings.

Timekeeping

Use the Timekeeping Mode to set and view the current time and date.

• Pressing D displays the Last Signal screen (date and time the time calibration

signal was last received) in the Timekeeping Mode.

Last Signal Screen

▲

Press D.

Day of week

Receive date

Receive time

Month – Day Hour : Minutes Seconds

indicator

▲

Alternate at the

1 second interval

Setting Up the Watch for Use in Western Europe

You need to make the following three settings before using this watch in Western

Europe. The following provides a general overview of the setting procedure. For full

details, see “Setting the Time and Date Manually” and “Time Calibration Signal

Reception”.

• Specify the city code for your Home City (the city where you will normally use the

watch).

• Select the auto summer time (DST) setting.

• Perform the manual time calibration signal receive operation to set the current time.

To set up the watch for use in Western Europe

1. In the Timekeeping Mode, hold down A until the

current auto receive on/off setting to flash, which

indicates the setting screen.

2. Press C to move the flashing to the city code setting.

3. Use D(+) and B(–) to select the city code you want to

use as your Home City.

City code

• The following are the city codes for major cities in the

Western Europe time zones.

BER and PAR: Berlin, Paris, Milan, Rome,

Amsterdam, Hamburg,

Frankfurt, Vienna

LON: London

4. Press C to display the summer time (DST) setting

screen.

5. Use D to select A (auto DST).

• Auto DST specifies auto switching between Daylight

Saving Time and Standard Time.

6. Press A to exit the setting screen.

7. Hold down D for about two seconds until the watch

beeps.

• Release D and the message RC! appears to indicate

that signal reception has started.

• Time calibration signal reception takes from two to six

minutes. Take care that you do not move the watch

during this time.

Receive indicator

• If the watch is indoors, we recommend that you place the watch near a window to

allow better signal reception.

• After signal reception is complete, the display of the watch changes to the Last

Signal screen.

Time Calibration Signal Reception

This watch is designed to pick up a time calibration signal and update its time setting

in accordance with the signal. There are two different methods you can use to receive

the signal: Auto Receive and Manual Receive. With Auto Receive, the watch

automatically receives the calibration signal three times each day and makes

appropriate adjustments. With Manual Receive, you perform a specific button

operation to receive the calibration signal.

Before performing a signal receive operation, remove the watch from your wrist and

position it as shown in the illustrations below.

• If your watch has a resin band, pass the end of the band through the band loop and

place the watch on a stable surface.

Resin band Metal band

Pass through band loop.

Note

• If you are using the time calibration signal to set the time for this watch, be sure to

correctly set your Home City. Otherwise, there is the chance that the watch will not

set the correct time. See “Setting the Time and Date Manually” for details.

• Note that signal reception is possible only when the watch is within range of a time

calibration signal transmitter, and BER, PAR, LON, or ATH is selected as the Home

City code.

• See “City Code Table” for a complete list of available city codes.

• The current time setting in accordance with the time calibration signal takes priority

over any time settings you make.

• Auto receive is turned on when the watch is shipped from the factory.

• See the information under “Time Calibration Signal Reception” if you experience

problems with time calibration signal reception.

To perform manual time calibration signal reception

1. Place the watch on a stable surface so its top (12 o'clock side) is facing in the

general direction of the signal transmitter.

• Note that signal reception is poor if the watch is on its back or side.

2. In the Timekeeping Mode, hold down D for about two

seconds until the watch beeps.

• Release D and the message RC! appears to indicate

that signal reception has started.

• Time calibration signal reception takes from two to six

minutes. Take care that you do not move the watch

during this time.

• After signal reception is complete, the display of the

watch changes to the Last Signal screen.

• The receive indicator indicates that the time calibration

reception attempt was successful.

Receive indicator

Note

• To interrupt a receive operation and return to the Timekeeping Mode, press D.

• If the receive operation is unsuccessful, the message ERR appears on the display

for about one or two minutes. After that, the watch returns to the Timekeeping Mode.

• You can also change from the Last Signal or ERR screen to the normal timekeeping

screen by pressing D.

Wave Ceptor 2554 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info