Bedienungsanleitung Weinberger KP-6241 (Seite 1 von 2) (Englisch)

749863

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Digital Wrist Blood

Pressure Monitor

KP-6241

- Instructions for use -

12/2010

Introduction

thank you for deciding for the blood

pressure monitor KP-6241 from

Weinberger GmbH & Co. KG. To be able

to utilise all advantages of the blood

pressure monitor to the fullest, you

should carefully read these instructions

before using the monitor. Keep the

instruction leaflet in a safe place.

Safety instructions

The blood pressure monitor KP-6241

enables you to monitor your blood

pressure regularly. However, you should

never change the treatment which your

doctor has prescribed

Self-measurement means monitoring,

it does not imply diagnosis or

treatment.

Discuss unusual values with your doctor.

Do not change the medication

prescribed by your doctor.

The heart rate is not a useful indicator of

the frequency of a cardiac pace maker.

Patients with cardiac arrhythmia should

use the blood pressure monitor only after

consulting a doctor.

Features of the KP-6241

• The blood pressure monitor has fuzzy

logic to identify the pumping pressure.

If the pumping pressure set in the

factory is not sufficient, the device

identifies this and continues pumping.

• The device has 85 memory locations.

• The date and time are displayed and

stored together with every blood

pressure value.

• If the battery icon is displayed, the

batteries are discharged and the device

cannot be used until new batteries are

inserted.

• WHO-Interpretation of blood pressure

readings with colored band (See

description at page 7).

- 2 -

• The handcuff is suitable for wrists

from 135 to 195 mm circumference.

Preparing the monitor for

measurement / changing batteries

Insert the two supplied batteries in the

battery compartment at the side of the

blood pressure monitor as shown.

Use only alkali batteries (LR03).

If the batteries are depleted, the battery

icon is displayed in the top left corner

of the LC display. The battery needs

urgent replacement because you cannot

use the monitor with depleted batteries.

Device description

Setting the clock

After you have inserted the two batteries,

you should set the clock.

To set the clock, hold the TIME button

pressed for about 5 seconds. The year

blinks in the top right corner of the

display.

Set the year with the 0/I-START button.

- 3 -

When the correct year is set, press the

TIME button again. Now the 1 blinks in

the top right corner of the LCD. It stands

for the month.

Set the month with the 0/I-START button.

Another press of the TIME button sets

another 1 blinking. It stands for the first

day in the month.

Set the day with the 0/I-START button.

Another press of the TIME button takes

you to the clock setting – the hours blink.

As earlier, set the clock with the 0/I-

START button.

Pressing the TIME button advances to

the minutes setting.

Set the minutes with the 0/I-START

button.

A final press of the TIME button

completes the setting of the date and

time.

How to obtain correct measuring

results

To obtain correct readings, measure the

blood pressure always

under the same

conditions, at rest, not

under the effect of

alcohol, not during

meals, not after heavy

physical or mental

stress. If possible, sit

down at a table for the

measurement.

Please note: The blood pressure monitor

must be at heart level during the

measurement, otherwise wrong readings

are obtained.

- 4 -

The measuring method

Put the cuff around your left wrist making

sure that the device rests on the artery

and the top edge of the device is about 1

cm away from the wrist joint (Please see

the enclose photo).

The cuff should be applied with moderate

tightness.

Pressing the 0/I-START button starts the

automatic measurement. The cuff inflates

to approx. 190 mmHg pressure.

The automatic deflation starts the

measurement. After about 3 seconds, a

heart icon starts blinking in the LC

display. If a Korotkoff’s sound is detected

already at that time, it means a

systolic pressure of more than 150

mmHg. Then the monitor re-inflates (to

about 220 mmHg). At the end of the

measurement, the result is displayed in

the LCD and the cuff deflates.

Aborting a measurement

You can stop the measurement at any

time by pressing the 0/I-START button.

The BP monitor deflates the cuff instantly.

- 5 -

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Weinberger KP-6241 Anleitung

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Weinberger KP-6241

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info