Bedienungsanleitung Wesen Inox Flat (Seite 4 von 14) (Englisch, Französisch, Portugiesisch, Spanisch)

618190

Zoom out

Zoom in

Vorherige Seite

1/14

Nächste Seite

–7–

The temperature will be set automatically when the button is released at the desired tem-

perature.

The thermostat will automatically disconnect the electrical connection when the pre-

determined temperature is reached. Once some water has been used and the tempe-

rature falls below the predetermined value, the thermostat will automatically reconnect

the electrical supply.

(4) Fault code function

[E1] Dry heating protection to prevent the electric heater run dry

[E2] Indicates a fault in the temperature sensor

[E4] Protection against overheating

ECO SELECTOR Technology

All WESEN water heaters allow precise and instant adjustment of water temperature,

thereby ensuring significant savings in terms of electrical consumption.

If the water heater is not going to be used for a long period of time and/or if there is a risk

of freezing, the device must be emptied via the safety relief valve.

Always:

- Disconnect the device from the electrical supply

- Close the cold water inlet stopcock

- Turn on a hot water tap

We recommend that you install a thermostatic valve set to a temperature of 39-41 ºC and

a flow rate of 6-8 litres per minute to obtain the best results from the appliance. This de-

vice will protect against burns as the water from the heater can reach 70 ºC or more. The

user should be aware of the risks involved in exposing parts of the body to excessively high

temperatures and take the necessary precautions to avoid them.

5. MAINTENANCE, CLEANING AND REPAIR

The water heater does not require any special maintenance and can be cleaned with a soft

damp cloth or sponge. Do not use abrasives or detergents.

Anode replacement

This appliance comes equipped with a magnesium anode for each electrical resistance. We

recommend that you check the condition of this every two years and replace it when ne-

cessary. Remember that this anode serves to protect the appliance against corrosion.

–6–

All electrical installations must incorporate an “EARTH” connection. The earthing con-

nection for the device is obligatory as the manufacturer will not be held responsible for any

damage caused by a device that is not earthed or for anomalies in the electrical supply.

The use of heating, gas and water installation pipes to connect the appliance to earth is

prohibited.

The use of adaptors and multiple power sockets is prohibited.

The appliance is not protected against the effects of electrical storms.

It is prohibited to connect the appliance to the electrical supply until it has been filled with

water.

NOTE: The manipulation and/or substitution of any parts (including the electrical power

supply cable) is strictly prohibited unless carried out by an Official Technical Support

Technician.

4. OPERATION

Before connecting the water heater to the electricity supply, it must be filled with water.

To do so, once the water heater has been installed, open the stopcock and turn on the hot

water taps. When water starts to come out, close the outlet taps, making sure that there

are no leakages. Do not connect the water heater to the electricity supply until you are

sure that the tank is completely full of water.

CONTROL PANEL

(1) On-off switch

(2) Power selection

By pressing the button (2), one or two power settings can be selected to obtain the

performance described in the technical characteristics section. The selected setting

will be indicated via the corresponding indicator light on the right-hand side.

(3) Temperature selection

Water temperature can be adjusted by pressing the button (3). The default setting is

35 ºC. Holding down the button will increase the temperature in 5 ºC intervals until

75 ºC is reached. In the case of going past the desired temperature, continue to 75 ºC

and then press the button again to return to the default setting of 35 ºC.

1 3

ENEN

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Wesen Inox Flat Seite 4

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Wesen Inox Flat

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info