Zoom out
Zoom in
Vorherige Seite
1/8
Nächste Seite
GB
-1-
Chart
PROGRAM SELECTION
BUTTON
Push “Programs” button
(repeatedly) until the indicator
of the required program lights
up (see “Table of programs”
below).
START/RESUME BUTTON
Push this button to start the selected program: the
indicator lights up and goes off at the end of the
program. When the door is opened during a
washing cycle, the cycle is temporarily paused: the
Start indicator blinks.
To resume the cycle push the Start button and
close the door within 3 seconds.
CANCEL/OFF BUTTON
Push this button to switch off the control panel.
If pressed when a program is running it cancels the
program ongoing draining water for 1 minute.
If pressed when the dishwasher is switched off it
drains any possible liquids from dishwasher (1
minute process).
If the indicator flashes repeatedly, see page 6 -
chapter ”What to do if ...”.
1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions
(without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
with sensor programs as a result of the appliance’s automatic calibration system.
2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for
detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
“nk_customer@whirlpool.com”.
Ta b l e o f p r o g r a m s
Deter-
gent
Consumption
P
Programs Loading instructions
Litres kWh
Minutes
1)
1
Pre-Wash cold
Crockery to be washed later. 5.0 0.02 10
2
Quickwash 40°C
Lightly soiled crockery, with no
dried-on food.
X 13.0 0.70 30
3
Eco
2)
50°C
Normally soiled crockery.
Energy-saving program.
X 15.0 1.05 165
4
Daily delay 3h 60°C
This program is activated after 3
hours, recommended for normally or
heavily soiled crockery.
X 16.0 1.35 120
5
Intensive 70°C
Recommended program for heavily
soiled crockery, especially suitable for
pans and saucepans.
X 15.0 1.50 140
5019 396 03507ADG 9500
BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.
Quick reference guide
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Forum

Suche zurücksetzen

Inhalt der Seiten


  • Page 1

    Chart

    Quick reference guide

    BEFORE USING THE APPLIANCE FOR THE FIRST TIME CAREFULLY READ
    THIS QUICK REFERENCE GUIDE AND THE ASSEMBLY INSTRUCTIONS!
    THE CONTROL PANEL OF THIS DISHWASHER ACTIVATES PUSHING
    ANY BUTTON EXCEPT CANCEL/OFF BUTTON.
    FOR ENERGY SAVING THE CONTROL PANEL DEACTIVATES
    AUTOMATICALLY AFTER 30 SECONDS IF NO CYCLE HAS STARTED.

    PROGRAM SELECTION
    BUTTON
    Push “Programs” button
    (repeatedly) until the indicator
    of the required program lights
    up (see “Table of programs”
    below).

    START/RESUME BUTTON
    Push this button to start the selected program: the
    indicator lights up and goes off at the end of the
    program. When the door is opened during a
    washing cycle, the cycle is temporarily paused: the
    Start indicator blinks.
    To resume the cycle push the Start button and
    close the door within 3 seconds.

    CANCEL/OFF BUTTON
    Push this button to switch off the control panel.
    If pressed when a program is running it cancels the
    program ongoing draining water for 1 minute.
    If pressed when the dishwasher is switched off it
    drains any possible liquids from dishwasher (1
    minute process).
    If the indicator flashes repeatedly, see page 6 chapter ”What to do if ...”.

    Table of programs

    Consumption
    Detergent

    P

    Programs

    1

    Pre-Wash

    cold

    Crockery to be washed later.



    5.0

    0.02

    10

    2

    Quickwash

    40°C

    Lightly soiled crockery, with no
    dried-on food.

    X

    13.0

    0.70

    30

    3

    Eco 2)

    50°C

    Normally soiled crockery.
    Energy-saving program.

    X

    15.0

    1.05

    165

    4

    Daily delay 3h

    60°C

    This program is activated after 3
    hours, recommended for normally or
    heavily soiled crockery.

    X

    16.0

    1.35

    120

    5

    Intensive

    70°C

    Recommended program for heavily
    soiled crockery, especially suitable for
    pans and saucepans.

    X

    15.0

    1.50

    140

    Loading instructions

    Litres kWh Minutes 1)

    1) Program data obtained in conformity with European standard EN 50242, obtained under normal conditions
    (without additional options) and may vary depending on conditions. Differences of up to 20 minutes are possible
    with sensor programs as a result of the appliance’s automatic calibration system.
    2) Reference program for energy label in compliance with EN 50242 regulations. - Note for Testing Institutes: for
    detailed information on the EN/Standard loading comparison test and other tests, contact the following address:
    “nk_customer@whirlpool.com”.

    ADG 9500

    5019 396 03507
    GB -1-

  • Page 2

    First time use

    How to set water hardness in order to always assure the best cleaning results
    Water hardness should be set only
    before the first wash or if water
    hardness has been changed

    -

    Press and hold together Programs and CANCEL/Off buttons for minimum 3 seconds.

    -

    Programs LEDs will indicate the water hardness setting.

    -

    Press the Programs button to increase setting (when the level reaches 7, the next key press will set the level back to 1.

    -

    Wait 30 seconds (control panel switches off) or press START/Resume button to save setting.

    1. Ask your water supply company what the water hardness is...

    German
    degrees °dH

    Water hardness level is factory
    set for medium-hard water
    (level 4).
    Even if you use tablets which
    include salt functionality, you
    must still add regeneration salt
    since such detergents are not
    effective enough at softening
    hard water.

    French
    degrees °fH

    English
    degrees °eH

    2. ...enter this value on
    your dishwasher
    3 first PROGRAM LEDs
    lit on the panel
    (see table of programs)
    P1
    P2
    P3

    Water hardness
    level

    0-5

    0-9

    0 - 6.3

    Soft

    1

    6 - 10

    10 - 18

    7 - 12.6

    Medium

    2

    11 - 15

    19 - 27

    13.3 - 18.9

    Average

    3

    16 - 21

    28 - 37

    19.6 - 25.9

    Medium-hard

    4

    22 - 28

    38 - 50

    26.6 - 35

    Hard

    5

    29 - 35

    51 - 63

    35.7 - 44.1

    Very hard

    6

    36 - 50

    64 - 90

    44.8 - 62.4

    Extremely hard

    7

    Suggestions for detergent use
    Gel or Powder
    (rinse aid and
    salt)

    go to step 1
    (see “Daily
    check”)

    Tablets

    if water is
    HARD extra salt
    needs to be
    added
    (go to step 1,
    “Daily check”)

    At first time use, the salt reservoir has to be filled independently from water hardness level (see description below in step 1 “Daily check”).

    Daily check

    Filling the salt reservoir - Dissolve limescale (not necessary if water hardness level is set to “soft”!)

    1
    1- salt reservoir
    2- rinse aid dispenser
    3- detergent dispenser
    4- racks system
    5,6,7,8- available functions on the panel
    9- filters
    10- spray arms

    Visual indicator
    (depending
    on the model).
    Unscrew cap.

    Screw on the cap.
    Salt residual
    around the cap
    need to be
    removed. Some
    salt reservoir have
    a level indicator
    integrated in the
    cap (see below
    how to check).
    Fill the salt reservoir with water
    before the first wash only.

    Add salt (never add detergent!)
    min. 0.8 kg / max. 1 kg

    (depending on the model)
    The salt level indicator lamp may remain lit Salt indicator on the control panel
    at the end of several wash cycles. If the
    The indicator lamp lights up when SALT
    water hardness level falls within category
    NEEDS TO BE ADDED.
    (soft), no salt is required.

    Salt indicator on the salt reservoir cap
    green: OK.

    clear: NEEDS TO
    BE ADDED

    GB -2-

  • Page 3

    Daily check

    Adding rinse aid (not necessary when you use tablets). How to adjust the rinse aid dosage regulator

    2

    Visual
    indicator

    If required,
    open the
    cover B
    (press the
    dedicated
    button).

    Check the rinse aid indicator to check the level
    into the dispenser.

    The rinse aid dosage can be
    adjusted to the detergent used.
    The lower the setting, the less
    rinse aid is dispensed (factory
    setting: position 4).
    Press the button to open the
    cover B. Using a coin or similar
    object, turn the arrow to the
    desired setting. After adjusting
    the rinse aid setting, shut the
    cover again.

    Add rinse aid
    to the max.
    line ~150 ml

    (depending on the model)
    Rinse aid indicator on the control panel

    Rinse aid indicator on the dispenser

    The indicator lamp lights up when RINSE AID NEEDS
    TO BE ADDED.

    dark: OK.

    clear: NEEDS TO BE ADDED

    Only use rinse aids recommended for use in domestic dishwashers. Immediately wipe away any rinse aid spilt accidentally. This prevents the formation of excess suds which can cause a fault function of the
    appliance.
    If there are streaks: reduce the dosage by turning the dial to a lower setting (1-3). If crockery is not perfectly dry: increase the dosage by turning the dial to a higher setting (5-6). Plastic dishes have more difficulty
    drying and a higher rinse aid setting will not improve the situation.
    Detergents with rinse aid incorporated may be effective only with longer programs. In the case of shorter programs, detergent residue may be a problem (if necessary, use powder detergent). Detergents with
    rinse aid incorporated tend to form excess suds.

    Daily use

    Adding detergent - Use only detergent specifically for dishwashers in accordance with the supplier’s recommendations
    Open the cover A
    (press the dedicated button).

    3

    Insert detergent: Tablet / powder / liquid into the big chamber

    Only fill the
    detergent dispenser
    prior to starting a
    wash program.

    Shut the cover
    by pressing dedicated ribs.

    Use only one tablet per one cycle, only
    placed in detergent dispenser.
    All types of tablets can be used, but for
    2 in 1 type adding of salt is mandatory.

    GB -3-

  • Page 4

    How to load the racks

    How to load UPPER RACK

    4

    (depending on the model)
    A - Adjustable flaps: in horizontal position for
    cups/long utensils.

    B - Cutlery basket - half: can be placed in the upper rack
    when the “Half load/Multizone” option is selected.
    The Grid (G) should be removed.

    How to adjust upper rack height (if available).
    It could be useful to lift up the upper rack to have
    more space in lower rack or bring it down to load
    long stem glasses.
    - Grasp and take out the two lateral handles (C)
    (they must be on the same level) and lift up or take
    down the upper rack.

    How to remove the upper rack (if available)
    It could be useful to remove the upper rack to load bulky items in the lower rack.
    - Open the two retainers (D) to take off the upper rack (when the upper rack is in
    place the retainers must always be closed).

    D - CLOSED

    D - OPEN

    How to load LOWER RACK
    (depending on the model)
    E - Foldable plate holders: they can be folded down to load pots
    or Fixed plate holders
    F - Cutlery basket: slide halves apart to split the basket.
    G - Grid: helps to keep the cutlery separate for better washing results.

    5

    Arrange crockery so that water does not collect in cavities, ensuring that the spray arms turn freely. Only use dishwasher-proof crockery and dishes. Do not use the dishwasher for washing wooden
    items, aluminium, tin, silver cutlery or decorated crockery (unglazed). In the baskets, dishes (e.g. plates, bowls, pots) must be placed in a correct way to let water flow down!

    Switching on the appliance. Press any button (except CANCEL/Off button) to switch on the control panel and start programming.

    GB -4-

  • Page 5

    Select program

    6

    Overview of programs
    The max. possible number of programs is illustrated in the chapter “Chart”. The corresponding programs for your appliance can be found on the panel (page 1).
    Choose program according to the attached table of programs (page 1).
    Duration of the program depends on the external conditions in the apartment, temperature and pressure etc.

    Wash cycle

    7

    The dishwasher door must be closed and the water tap open.
    To pause the program (e.g. if you want to insert an item):
    - Open the door with caution (the program pauses) and insert
    the item/s,
    (beware of HOT steam!).
    - Press the START button and close the door within 3 seconds
    (the program resumes the cycle from where it was
    interrupted).

    To Cancel the program on running:
    - Open the door, press the CANCEL/
    Off button and close the door.
    - (Water drains for up to 1 minute then
    the appliance switches off).

    To change the program in progress:
    - Open the door, press the CANCEL/Off button to cancel the
    running program and close the door.
    - (Water drains for up to 1 minute then the appliance switches off).
    - Open the door and press any button except CANCEL/Off button to
    switch on the appliance.
    - Select a new program.
    - Press the START button and close the door within 3 seconds

    Switching off the appliance. Everything OK...

    8

    After the program is completed appliance turns into Standby mode automatically. All indicator lamps switch off.
    Exercise caution when opening the door: beware of hot steam.
    Unload the appliance starting from the lower rack in order to avoid any residual drips of water falling onto crockery below.

    Maintenance and care

    Maintenance and care

    9

    Screw on microfilter NOTE MARK!

    Filters
    Check and
    clean if
    necessary

    Insert

    Rinse under
    running water...

    Unscrew
    microfilter (1),
    remove it (2)
    and remove
    fine sieve (3)...

    Rectifying minor faults yourself...

    10

    Spray arms
    Remove
    blockages/
    deposits.

    Insert and screw on upper and lower arms tightly.
    Unscrew
    and remove
    upper arm...

    Unscrew
    and remove
    lower arm...

    Clean spray
    nozzles under
    running water
    (use toothpicks
    if necessary)...

    GB -5-

  • Page 6

    What to do if...
    If a fault occurs, before contacting the After-sales Service, make the following checks to try and remedy the problem.
    Most faults can be remedied by taking the following courses of action, quickly restoring normal appliance operation.
    The appliance...
    ...is not working/will not start

    ...the CANCEL/Off indicator lamp blinks 6
    times

    ...the CANCEL/Off indicator lamp blinks 6
    times/wash program ended too early
    (dishes are dirty and wet)

    ...the CANCEL/Off indicator lamp blinks 8
    times

    -

    Possible causes...
    The appliance must be switched on.

    Solutions...
    - Check the household circuit fuse if there is no power supply.

    -

    The dishwasher door doesn’t close.

    - Check if the dishwasher’s door is closed.

    -

    “Delayed start” option is ON.

    - Check whether the “Delayed start” option (if available) has been selected. If it has, the appliance will only
    start once the set time has elapsed. If necessary, set the delayed start to “0” (RESET the appliance).

    -

    Water tap closed.

    - The water tap must be open.

    -

    Kinked water inlet hose or clogged inlet filters.

    - The water inlet hose must not be kinked and the relative inlet filter in the water tap connector must not be
    dirty or clogged.

    -

    Water pressure too low.

    - The water tap must be fully open during water inlet (minimum capacity: 0.5 litres per minute).

    -

    Dirty or clogged filters.

    - The filters must not be dirty or clogged.

    -

    Too little water in the dishwasher’s water system.

    - Concave items (e.g. bowls, cups) must be arranged facing downwards in the rack.

    -

    Drain hose incorrectly fitted.

    - The drain hose must be fitted correctly (for high mounted appliances, leave min. 200-400 mm from the
    lower edge of the appliance) - see Assembly instructions.

    -

    High level of foam inside.

    - Repeat without detergent or wait until foam disappears.

    -

    Dirty filters.

    - Clean the filters.

    -

    Kinked drain hose.

    - The drain hose must not be kinked.

    -

    Syphon hose connection closed.

    - The closure disk of the syphon hose connection must be removed.

    After taking the above course of action, the fault message must be reset. In the majority of cases the fault is thus eliminated.
    RESET:

    Crockery and cutlery...
    ...are not perfectly clean/have food residues -

    Press the CANCEL/Off button.
    Close the door.
    Water drains automatically for up to 1 minute.
    The appliance is now ready to be restarted.

    Possible causes...
    Solutions...
    Too little space between dishes (incorrect arrangement - Arrange crockery so that items do not touch each other. Concave items (e.g. bowls, cups) must be
    of the concave items in the rack).
    arranged facing downwards in the rack.
    necessary, use more detergent, observing the manufacturer’s indications as regards dosage. Always store
    Too little detergent; detergent too old or incorrectly stored. - If
    detergent in a dry place and do not store it for excessively long periods of time.
    heavily soiled crockery, select a wash program with a higher temperature (see table of programs Temperature not high enough for heavily soiled crockery. - For
    page 1).
    Loading of the dishwasher using lower and upper rack - If you select the “Half load/Multizone” option (if available), remember to load only the upper rack or only
    at the same time with “Half load/Multizone” option.
    the lower rack to increase washing power and thus obtain optimum wash results.
    - In the event of frequent use of the Eco 50°C program (if available), from time to time select the Intensive
    Frequent use of Eco 50°C.
    70°C program (if available).
    The spray arms must not be clogged, the filters must not be dirty and must be fitted correctly (see page 5,
    Clogged spray arms, dirty filters or not fitted correctly.
    “Maintenance and care“).
    Spray arms stuck impeded by crockery or cutlery.

    - The spray arms must be able to turn freely and must not be impeded by crockery or cutlery.

    GB -6-

  • Page 7

    What to do if...
    Crockery and cutlery...

    Possible causes...

    Solutions...

    ...salt indicator lit

    -

    Use tablets for soft water.

    - Set “Tablet” option; if this option is not available, it is normal for the salt indicator to light up.

    ...have deposits: regeneration salt residue

    -

    Water too hard.

    - In areas with very hard water, more regeneration salt needs to be added (see page 2, “How to set water
    hardness”).

    -

    Salt reservoir cap open.

    - Close the salt reservoir cap properly.

    -

    Not enough rinse aid.

    - If you use a combined action detergent, try adding more rinse aid.

    -

    Plastic containers dry badly.

    - Synthetic materials do not dry well; if wet at end of cycle, wipe dry.

    -

    Clean dishes left in dishwasher for a long time after end - In this situation, the presence of drops of water on dishes and on the sides of the dishwasher is normal.
    of cycle (e.g. when using “Delayed start” option).
    Try releasing the door 5 minutes before removing the dishes.

    -

    Incorrect arrangement of the concave items in the rack. - Arrange crockery so that water does not collect in cavities.

    -

    Incorrect dosage the rinse aid.

    - Increase the dosage of rinse aid (see page 3, “Adding rinse aid”).

    -

    Rapid program selected.

    - The Rapid program 40°C / 45°C is intended for quickly washing lightly soiled dishes. If used for a full load of
    medium/heavy soiled dishes, the dishes may not dry completely. If so, select a standard-length program. For best
    results, open the door after the end of the program and wait 15 minutes before unloading the dishwasher.

    ...have discoloured plastic parts

    -

    Tomato/Carrot juice.

    - Tomato sauce, for example, can lead to discolouring of plastic parts. Powder detergent is recommended as
    it allows slightly higher doses to be used for improved whitening. Programs with higher wash temperatures
    should be used.

    ...opaque glasses, etc.

    -

    Dishes unsuitable for washing in dishwashers (porcelain),

    - Only use dishwasher-proof crockery and dishes.

    ...removable deposits on glasses

    -

    Usage of incorrect programs for glasses.

    - Dishes should be put together, to avoid touching each other. Do not put glassware together in baskets.
    Use suitable program for glass.

    ...glasses not sparkling

    -

    Not conform of glasses to washing in dishwashers
    (porcelain).

    ...permanent deposits on glasses

    -

    Rainbow effect.

    -

    ...tea cups darken and dirt does not
    disappear after washing in dishwasher

    -

    Not known.

    - This phenomenon is inevitable. Theine alters colours permanently.

    ...rust marks

    -

    Pre-wash program not used.

    - Salty or acidic food residues can cause rust marks even on stainless steel cutlery. To avoid this, always use
    the pre-wash program if the dishes are to be washed later.

    ...other marks

    -

    Rinse aid dosage too low.

    - In the presence of marks, increase the rinse aid dosage (see page 3, “Adding rinse aid”).
    - If you use a combined action detergent, possibly add more rinse aid.

    ...streaks

    -

    Rinse aid dosage too high.

    - In the presence of streaks, reduce the rinse aid dosage (see page 3, “Adding rinse aid”).
    - If you use a combined action detergent which includes rinse aid, do not add any additional rinse aid.

    ...suds

    -

    Unsuitable dosage of detergent/rinse aid.

    - Only use the amount of detergent/rinse aid required, since excessive amounts can lead to excess suds.

    ...are not dry

    - Some kinds of glass cannot be washed in the dishwasher.
    This phenomenon is irreversible. We recommend in future:
    Change the control of system of dosage of softener.
    Be careful – follow recommended detergent dosage.
    For combined action tablets see detergent producer’s recommendations.

    GB -7-

  • Page 8

    What to do if...

    Disconnect the mains plug

    If, after carrying out the above checks, the fault persists, disconnect the mains plug and turn off the water tap. Contact the After-sales Service (see warranty).
    Before contacting our After-Sales Service, take note of the following:
    - the description of the fault,
    - the appliance type and model,
    - the service code (the number indicated on the adhesive rating plate) inside the door on the right-hand side:

    Precautions and general recommendations
    1. Packing
    The packaging materials are 100% recyclable and marked with the recycling symbol
    .
    2. Removing the packaging and inspecting the contents
    After unpacking, make sure that the dishwasher is undamaged and that the door closes correctly. If in doubt,
    contact a qualified technician or your local retailer.
    3. Before using the dishwasher for the first time
    - The appliance is designed to operate at ambient temperatures of between 5°C and 45°C.
    - This dishwasher has been tested by the manufacturer to ensure it functions correctly. Such testing may
    leave slight drips/water marks which will disappear with the first wash.
    4. Energy and water savings
    - Do not rinse crockery under running water.
    - Always fully load the dishwasher before running it or select the “Half load/Multizone” option (if available).
    - If ecological energy sources are available such as solar panel heating, heat pumps or centralised heating
    systems, the appliance may be connected to the hot water mains up to a maximum temperature of 60°C.
    Make sure the water inlet hose is of the correct type (“70°C Max” or “90°C Max”).
    5. Child safety
    - Keep the packaging materials out of the reach of children.
    - Children must not be allowed to play with the dishwasher.
    - Store the detergent, rinse aid and salt out of the reach of children.
    6. Safety warnings
    - The appliance is not intended for use by children or physically or mentally impaired persons, unless
    adequately supervised by a responsible adult capable of guaranteeing safe use of the appliance.
    - Do not operate the appliance in the open air.
    - Do not store flammable materials in close proximity to the dishwasher.
    - The water in the dishwasher is not potable.
    - Do not use solvents inside the dishwasher: risk of explosion!
    - Be careful when the door is open: risk of tripping!
    - The open dishwasher door can only support the weight of the loaded rack when pulled out. Do not rest
    objects on the open door or sit or stand on it.
    - Sharp items that might cause injury (e.g. knives), must be placed in the cutlery basket with the sharp end
    facing downwards. Long-handled utensils must be arranged horizontally in the upper rack, with the sharp
    end facing away from the front of the appliance.

    - Before cleaning or carrying out maintenance, disconnect the mains plug and turn off the water tap; also in
    the event of any malfunction.
    - Repairs and technical modifications must be carried out exclusively by a qualified technician.
    7. Resistance to frost
    If the appliance is placed in surroundings exposed to the risk of frost, it must be drained completely. Turn off
    the water tap, remove the inlet and outlet hoses, and let all the water drain away. Make sure there is at least
    1 kg of dissolved regeneration salt in the salt reservoir, to protect the appliance from temperatures of up to
    -20°C. When the program resumes, an error message may be indicated (see page 6).
    CANCEL/Off indicator blinks 6 times - the appliance must remain at an ambient temperature of min. 5°C for
    at least 24 hours.
    After eliminating these faults, RESET the appliance (see chapter “What to do if...”).
    8. Disposal
    - The appliance is manufactured using recyclable materials. If you decide to scrap the dishwasher, it must be
    disposed of in compliance with local waste disposal regulations. Make it unusable by cutting off the power
    cord. To prevent situations of potential danger to children (e.g. danger of suffocation), break the lock of the
    door so that it can no longer be closed.
    - This appliance is marked according to the European directive 2002/96/CE on Waste Electrical and
    Electronic Equipment (WEEE). By ensuring that this appliance is scrapped suitably, you can help prevent
    potentially damaging consequences for the environment and health. Unsuitable disposal of an appliance of
    this type as household waste could have detrimental effects on the environment. The symbol
    on the
    appliance, or on documentation enclosed with the appliance, indicates that this product must not be
    treated as household waste, but must be delivered to the nearest collection centre for the recycling of
    electrical and electronic appliances. Disposal must be carried out in accordance with local environmental
    regulations for waste disposal. For further information on the treatment, recovery and recycling of this
    appliance, contact your competent local authority, the collection service for household waste or the shop
    where you purchased the appliance.
    EC Declaration of conformity
    This appliance has been designed, constructed and distributed in compliance with the safety requirements of
    EC Directives:
    2006/95/CE, 89/336/CE, 93/68/CE and 2002/95/CE (RoHS Directive).
    Loading Capacity: 12 place settings.

    The guarantee is not applicable if faults are caused by incorrect use of the appliance.

    We reserve the right to make technical modifications.

    GB -8-




Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Whirlpool ADG 9500 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Whirlpool ADG 9500 in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 1,64 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Andere Handbücher von Whirlpool ADG 9500

Whirlpool ADG 9500 Kurzanleitung - Deutsch - 8 seiten

Whirlpool ADG 9500 Kurzanleitung - Holländisch - 8 seiten

Whirlpool ADG 9500 Kurzanleitung - Französisch - 8 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info