Bedienungsanleitung Whirlpool AKT 316 (Seite 2 von 2) (Englisch)

662511

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

BEFORE USING THE COOKING HOB

Before use, remove:

- adhesives stuck on the hob;

- cardboard guards and protective plastic film;

- check whether the hob has been damaged during

transport. If in doubt, contact the After Sales Service.

Care and Maintenance

• Clean the hob, when it is cool, after each use. This will

prevent the build-up of dirt and make cleaning easier.

• Use a clean cloth, absorbent kitchen wipes and washing

up liquid or a specific glass ceramic cleaner.

• Remove baked-on dirt with the special scraper tool

(if provided) and specific cleaning products.

• Any food spills should be cleaned off before they dry.

• Do not use abrasive products, chlorine-based cleaners,

oven-cleaner spray or pan scourers.

• The hob should be treated periodically with specific

products available from the shops, following the

manufacturer's instructions.

TROUBLESHOOTING GUIDE

The hob does not work:

- Make sure that the power supply is on.

- Turn the hob off and on again, to make sure that the

problem has been solved.

- Make sure that the knob is not turned to “0”.

Turn the multi-pole switch to “Off” for a few minutes and

then turn it back to “On”.

AFTER SALES SERVICE

Before you call the After Sales Service:

• Make sure that you cannot solve the problem yourself

following the points described in chapter

“Troubleshooting Guide“.

If after the above checks the fault still occurs, get in touch

with the nearest After Sales Service.

Please give:

• a short description of the fault;

• the exact type and model of the hob;

• service number (i.e., the number that follows the word

SERVICE on the rating plate, located under the hob

itself);

•your full address;

• your telephone number and area code.

If any repairs are required, please contact an authorised After

Sales Service (to guarantee that original spare parts will be

used and repairs carried out correctly).

Failure to comply with these instructions may compromise

the safety and quality of the product.

INSTALLATION

Recommendations

Important: Disconnect the hob from the mains before

carrying out any installation work or servicing.

• All electrical connections must be made before

connecting the appliance to the power supply.

• Installation must be carried out by a qualified technician

in accordance with the manufacturer's instructions and in

compliance with local regulations.

• Unpack the hob and make sure that the appliance has not

been damaged during transport.

If you are not sure contact the dealer or the nearest

service centre.

Preparing the housing unit

• Cut the worktop to fit before installing the appliance.

Carefully remove any shavings or sawdust that could

prevent the appliance from running properly.

• The hob must be fitted in a worktop with a minimum

thickness of 30 mm and a maximum of 50 mm.

• Insert a separator at least 20 mm from the lower edge of

the hob, so that it cannot be accessed by the user.

• If there is an oven under the hob, make sure that it is

manufactured by Whirlpool and equipped with a cooling

system.

• There must be nothing between the hob and the oven

(e.g. cables, insulating material, etc.).

• An adjacent column unit must be installed at least

100 mm from the edge of the hob (fig. 2).

• Cut an opening in the worktop of the given dimensions.

• We recommend you seal the internal edges of the

worktop with wood glue or silicone.

• If not already in place, apply the supplied seal to the hob,

after cleaning the adhesive surface thoroughly.

Glass ceramic hob

Important: remove any protective film before installing the

hob.

Make sure that the opening in the worktop for the hob is cut

according to the dimensions given in the drawing, paying

attention to the tolerance range.

The hob should not be forced into the worktop. Forcing the

glass ceramic top may cause it to crack (even at a later date)!

• If the worktop is made of wood, use the spring clips and

screws provided.

1. Secure the spring clips (A) (fig. 1) with the screws supplied,

paying attention to the specified distances.

2. Fit the hob into the worktop.

ASSEMBLY:

After having cleaned the perimeter surface, apply the

supplied gasket to the hob as shown in the fig. 4.

Connecting the hob to the power supply

Note: the yellow/green earth wire must be connected to the

screw marked .

If the supply cable is not already connected:

• Strip away approximately 70 mm. of the outer sheath of

the cable.

• Then strip away approximately 10 mm. of the inner

sheath.

• Open the terminal board by pushing the side clips in with

the help of a tool.

• Insert the cable in the cable clamp and connect the wires

to the terminal board (fig. 3).

• Close the cover of the terminal board.

• After the electrical connection, fit the hob from the top

and hook it to the fixing springs, as shown in fig. 1.

Fig. 4

Declaration of conformity

• This cooking hob has been designed, constructed and

marketed in compliance with:

- safety objectives of the “Low Voltage” Directive

2006/95/EC (which replaces 73/23/EEC and

subsequent amendments).

- protection requirements of EEC Directive “EMC”

2004/108.

- This cooktop is suitable for contact with foodstuffs and

complies with EEC (CE) Regulation n. 1935/2004.

PROTECTING THE ENVIRONMENT

Disposal of packaging materials

• The packing material can all be fully recycled, as confirmed

by the recycling symbol .

• The various parts of the packaging must not be sent for

waste, but recycled in conformity with the regulations

imposed by local authorities.

Disposal of used household appliances

• This appliance is marked according to the European

directive 2002/96/EC on Waste Electrical and Electronic

Equipment (WEEE). By ensuring this product is disposed

of correctly, you will help prevent potential negative

consequences for the environment and human health,

which could otherwise be caused by inappropriate waste

handling of this product.

The symbol on the product, or on the documents

accompanying the product, indicates that this appliance

may not be treated as household waste. Instead it shall

be handed over to the applicable collection point for

the recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local

environmental regulations for waste disposal.

For more detailed information about treatment, recovery

and recycling of this product, please contact your local city

office, your household waste disposal service or the shop

where you purchased the product.

Energy saving

• Use pots and pans whose bottom diameter is equal to, or

slightly larger than, that of the cooking zones.

• Only use flat-bottomed pots and pans.

• If possible, keep pot lids on when cooking.

• Cook vegetables, potatoes, etc. with little water in order

to cut down cooking time.

• A pressure cooker allows you to save even more energy

and time.

Fig. 2

Fig. 3

Fig. 1

Whirlpool AKT 316 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AKT 316

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info