450398
2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
5019 301 06374
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use.
1. Turn the
programme selector
to the desired programme
and temperature.
2. The
time display
shows the duration of the chosen
programme (in hours and minutes), and the
“Start (Pause)”
indication lamp
blinks.
3. The indication lamp of the predefined
spin speed
lights up.
Push the button(s) of any option(s) desired - the respective
indication lights up.
When the combination of programme and additional option(s) is
not possible, the indication lights switch off automatically.
Unsuitable combinations of options are deselected automatically.
“Clean+” button
Choose this option if you use an in-wash additive for stain removal
(powder, for example “Vanish”) - it will optimize the additive’s
efficiency to get better wash performance and stain removal.
Selectable for programmes “Cotton” and “Synthetics”; choose
temperature of 30 or 40°C and use with maximum load.
Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber, together with
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
Prolongs the programme by approx. 10 to 15 minutes.
Appropriate for use of stain removers and bleaches on oxygen
basis.
Chlorine or perborate bleaches must not be used!
“Prewash” button
Only for heavily soiled loads (for example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
Do not use liquid detergent for the main wash when activating
the “Prewash” option.
“Easy ironing” button
Can be used together with “Cotton, “Synthetics” and “Daily
load” programmes to make ironing easier.
Increases the water quantity and the clothes are spun very gently.
“Intensive rinse” button
More water is added and rinse cycle is prolonged.
This option is particularly suitable for areas with very soft
water, washing baby linen and helps people with allergies.
“Rinse hold” button
The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and prevent
colours from changing.
This option is particularly recommended for the programmes
“Synthetics”, “Daily load” and “Delicates”.
It is particularly useful if you want to postpone spinning to a
later time, or if you want to drain only.
If you select “Rinse hold” do not leave the laundry items to
soak for too long.
Note:
The programme stops to “Rinse hold” at the time the
“Rinse hold” light in the programme sequence indication is on.
The indication lamp next to the
“Start (Pause)”
button blinks.
Terminate the “Rinse hold” option:
Press the
“Start (Pause)”
button; the programme will
terminate automatically with the final spin cycle for the present
wash programme.
CONSUMPTION DATA
Programme
Te m p e r a t u re
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton 95 6.0 59
**
1.90 2:00
Coloured Cotton
60 6.0 49 1.02 2:20
Coloured Cotton 40 5.0 56 0.70 2:00
Synthetics 60 2.5 50
**
0.80 1:35
Synthetics 40 2.5 46 0.50 1:20
Delicates 30 1.5 60 0.50 0:45
Daily load 40 3.0 41 0.50 1:00
Quick wash 30 3.0 41 0.40 0:30
Wool 40 1.0 60 0.50 0:45
Handwash 40 1.0 45 0.50 0:40
Eco Cotton
***
60 6.0 49 0.78 4:00
Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary
with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the values in the table, because it takes into account the household conditions applicable at that time.
**
To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
***
Reference Programme for Energy Label.
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
If you do not wish to spin the clothes, turn the programme
selector to the “Drainprogramme and press the
“Start
(Pause)”
button.
“Spin” button
Every programme has a predefined spin speed.
Press the button to set another spin speed.
If spin speed “0” is selected, the final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only.
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
Select programme, temperature and options.
Press the “Start delay” button to select the delay time by 1 to 23 hours.
•Press the
“Start (Pause)”
button.
The countdown of the delay time begins; the “Start delay”
indication lamp and the dot on the display will keep blinking
until the programme starts.
The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
Once having pressed the
“Start (Pause)”
button, the number
of hours preselected can be reduced by pressing again the
“Start delay” button.
To cancel the “Start delay”
...before you press the “Start (Pause)” button:
Turn the programme selector to another position or press the
“Reset”
button.
...after having pressed the “Start (Pause)” button:
•Press the
“Reset
button for at least 3 seconds - the start
delay time disappears from the time display.
Open the tap and press the
“Start (Pause)”
button. The
indication lamp of the
“Start (Pause)”
button lights up. The
programme sequence indicator shows the current programme
phase, running from left to right through Wash, Rinse, Spin/Drain.
The time display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is the
case, an animation appears on the time display.
Before starting and after end of a programme, the lamp lights to
show that the door can be opened. As long as a wash programme
is running, the door remains locked and must on no account be
forced open. In case you have an urgent need to open it during a
running programme, refer to “Cancel (Reset) a running
programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a fault in an
electrical component. Refer to the “Troubleshooting Guide” in your
Instructions for Use; if the fault persists, contact our After Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open the water
tap; if the indication still lights up, refer to the “Troubleshooting
Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain hose is
kinked or the filter must be cleaned; in the latter case refer to the
Instructions for Use (“Removing the Filter”).
All the lights of the programme sequence indicator are off,
and the “Door open” indication lights up.
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start (Pause)”
button to pause the programme.
The light blinks.
2. Select the new programme (with temperature), any options
and another spin speed if you want.
3. Press the
“Start (Pause)”
button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
The
“Reset”
button cancels a programme before the end.
•Press the
“Reset
button for at least 3 seconds; “rES”
appears on the display. Any existing water is drained out
before the door can be opened.
START DELAY
PROGRAMME START
“DOOR OPEN” INDICATION
RED INDICATIONS
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
CANCEL (RESET) A RUNNING
PROGRAMME BEFORE THE END
30106374GB.fm Page 2 Wednesday, April 14, 2010 6:29 PM
Black process 45.0° 150.0 LPI
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Whirlpool Atlanta 1400 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Whirlpool Atlanta 1400

Whirlpool Atlanta 1400 Kurzanleitung - Deutsch - 2 seiten

Whirlpool Atlanta 1400 Bedienungsanleitung - Deutsch - 14 seiten

Whirlpool Atlanta 1400 Bedienungsanleitung - Englisch - 14 seiten

Whirlpool Atlanta 1400 Bedienungsanleitung - Englisch, Holländisch - 13 seiten

Whirlpool Atlanta 1400 Kurzanleitung - Holländisch - 2 seiten

Whirlpool Atlanta 1400 Kurzanleitung - Französisch - 2 seiten

Whirlpool Atlanta 1400 Bedienungsanleitung - Französisch - 13 seiten

Whirlpool Atlanta 1400 Bedienungsanleitung - Türkisch - 13 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info