Zoom out
Zoom in
Vorherige Seite
1/13
Nächste Seite
1
1

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Inhalt der Seiten


  • Page 1

    1



  • Page 2

    CONTENTS
    QUICK REFERENCE GUIDE
    PLEASE READ INSTRUCTIONS
    FOR USE BOOKLET!

    PROGRAMME CHART
    PREPARING THE LAUNDRY
    SELECTING A PROGRAMME AND OPTIONS
    STARTING AND COMPLETING A PROGRAMME
    CHANGING A PROGRAMME
    INTERRUPTING A PROGRAMME
    DAILY MAINTENANCE AND CLEANING

    INSTRUCTIONS FOR USE
    BOOKLET

    2

    BEFORE USING THE DRYER

    Page

    3

    PRECAUTIONS AND GENERAL
    RECOMMENDATIONS

    Page

    5

    ELECTRICAL CONNECTION

    Page

    7

    DESCRIPTION OF THE DRYER

    Page

    8

    REMINDER - MAINTENANCE AND CLEANING

    Page

    8

    CLEANING THE LINT FILTER

    Page

    8

    CLEANING THE HEAT EXCHANGER

    Page

    9

    DRAINAGE SYSTEM

    Page

    10

    DOOR REVERSIBILITY

    Page

    11

    TROUBLESHOOTING GUIDE/
    AFTER-SALES SERVICE

    Page

    12



  • Page 3

    BEFORE USING THE DRYER
    • This dryer is exclusively designed to dry machine
    dryable laundry in quantities which are usual for
    private households.
    • Observe the instructions given in these Instructions For
    Use and the Programme Chart before using the dryer.
    • Keep the Instructions For Use and the Programme
    Chart handy for reference. If you pass on the dryer to
    others, make sure that the Instructions For Use and
    the Programme Chart go with it.
    • The manufacturer declines all liability for damage to
    property or injury to persons or animals due to noncompliance with the directions given in these
    Instructions For Use.
    1. Removing the packaging and inspection
    • After unpacking, make sure that the dryer is
    undamaged. If in doubt, do not use it. Contact the
    After-Sales Service or your local retailer.
    • If the appliance was exposed to the cold prior to
    delivery, keep it at room temperature for a few hours
    before operating.
    • Do not operate the dryer if it has been damaged
    during transport. Contact one of our After-Sales
    Service technicians.
    2. Electrical Connections
    • Electrical connections must be carried out by a
    qualified technician in compliance with the
    manufacturer’s instructions and current standard
    safety regulations.
    • Electrical connections must comply with local
    Electricity Board regulations.
    • Data regarding voltage, power consumption and the
    required fuse protection is shown on the rating plate
    mounted at the rear of the dryer.
    • The dryer must be earthed as prescribed by law.
    • Before carrying out any maintenance on the dryer
    disconnect it from the mains supply.
    • Mains cable replacement must only be carried out by
    the After-Sales Service.
    • After installation, access to the mains plug or to an allpole disconnection switch must be ensured at all times.
    • Light bulb replacement must only be carried out by
    the After-Sales Service.
    3. Installation
    • Do not install your dryer where it may be exposed to
    extreme conditions, such as: poor ventilation,
    temperature below 5°C or above 35°C.
    • The appliance must not be installed behind a lockable
    door, a sliding door or a door with hinges on the
    opposite side to that of the tumble dryer, in such a
    way as to prevent the tumble dryer door from being
    fully opened.

    • Small indoor located storage rooms, bathrooms,
    toilets, shower rooms and enclosed areas without
    ventilation are not suitable locations for installation of
    the dryer. If it must be installed in such a location,
    adequate ventilation must be ensured (open doors,
    ventilation grid or slot larger than 500 cm²).
    • Before running the first cycle, ensure that the water
    container is fully pushed inside and that the heat
    exchanger is correctly positioned.

    • Before running the first cycle, ensure that all of the
    drainage system hoses are connected (as shown in
    the picture below).

    • If possible use a hose to drain the water directly into
    the domestic plumbing system. This will avoid having
    to empty the water container at the end of each
    drying cycle, since the condensation water can be
    directly drained away. Also see section entitled
    “Drainage System”.
    • Take care not to install the dryer on a deep-pile carpet.
    • Take care not to trap the mains cable between the
    dryer and the wall.
    • When installing the dryer make sure that the four feet
    are stable and resting on the floor, adjusting them as
    required, and check that the machine is perfectly
    level using a spirit level.
    • If, due to lack of space, the dryer must be installed
    directly next to a gas or coal stove, a heat insulating
    plate (85 x 57cm) must be installed in between and
    the side of the plate facing the stove must be covered
    with aluminium foil.
    3



  • Page 4

    • The dryer is not designed for built-in installation.
    • The dryer can be installed under a worktop,
    provided that adequate ventilation of the dryer is
    assured. Install a ventilation grid (minimum 45 cm x 8
    cm), in the rear part of the worktop under which the
    dryer is installed.

    D. Secure both distance holders by turning them in a
    clockwise direction as far as the stop position.

    D

    4. Assembly of distance holders
    To ensure that the appliance is positioned at a correct
    distance from the wall at the rear side and to allow
    sufficient ventilation, distance holders must be mounted
    on the rear side of the dryer before starting the first
    drying cycle.
    A. Remove the two distance holders from the packaging.
    B. The distance holders must be inserted on the rear
    side of the dryer in the protective cover.

    5. User and child protection
    • Children must not be allowed to play with the dryer.
    • Ensure that children and small animals cannot get into
    the drum.
    • Keep the packaging materials (plastic bags,
    polystyrene parts, etc.) out of reach of children, as
    they are potentially dangerous.
    • The appliance is not intended for use by persons
    (including children) with reduced physical, sensory or
    mental capabilities, or lack of experience and
    knowledge, unless they have been given supervision
    or instruction concerning use of the appliance by a
    person responsible for their safety. Children should
    be supervised to ensure that they do not play with
    the appliance.
    Stacking kit
    • Depending on the
    model, your dryer can
    be stacked on top of
    your front loading
    washing machine. For
    further information
    please contact the
    After-Sales Service.

    B
    C. Insert the distance holders in the holes provided on
    both sides.

    C
    4



  • Page 5

    PRECAUTIONS AND GENERAL
    RECOMMENDATIONS
    To minimise the risk of fire in the tumble dryer,
    the following precautions should be observed:
    • Oil-soaked items ignite spontaneously, especially
    when exposed to heat sources such as in a tumble
    dryer. The items become warm, causing an oxidation
    reaction in the oil. Oxidation creates heat. If the heat
    cannot escape, the item can become hot enough to
    catch fire. Piling, stacking or storing oil-soaked items
    can prevent heat from escaping and so create a fire
    hazard.
    • Do not dry unwashed items in the tumble dryer.
    • Ensure that the appliance is maintained as shown in
    the section “Maintenance and cleaning”.
    • Ensure that the appliance is installed as per the
    instructions above.
    • Items that have been soiled with substances such as
    cooking oil, acetone, alcohol, petrol, kerosene, spot
    removers, turpentine, waxes and wax removers
    must be washed in hot water with an extra amount
    of detergent before being dried in the tumble dryer.

    • Always set the programme/time selector knob to the
    “0” position after use. This prevents the dryer from
    being switched on accidentally.
    • Before cleaning or carrying out maintenance, switch off
    the dryer and disconnect it from the mains supply.
    • To clean the outside of the dryer, use a neutral
    detergent and a damp cloth.
    • Do not use abrasive detergents.
    • The final phase of a drying cycle always occurs
    without heat (cool-down phase) so that the items are
    left at a temperature which ensures that they will not
    be damaged.
    • Wipe away any lint from the door seal and the door
    using a damp cloth.
    • If the lint filter mesh is clogged, clean it with water
    and a soft brush.
    • Since lint can penetrate through the filter, it is
    necessary to clean the entire filter area (including
    below the filter) from time to time using a brush, a
    damp cloth or a vacuum cleaner.

    • Do not use flammable cleaning agents.

    EC Declaration of Conformity

    • Do not use the tumble dryer if chemicals have been
    used for cleaning.

    • This dryer has been designed, constructed and
    distributed in compliance with the safety
    requirements of EC Directives:

    • Items such as foam rubber (latex foam), shower caps,
    waterproof textiles, rubber backed articles and
    clothes or pillows fitted with foam rubber pads must
    not be dried in the tumble dryer.

    • 2006/95/EC Low Voltage Directive
    • 2004/108/EC Electromagnetic Compatibility
    Directive

    • Fabric softeners or similar products should be used
    as specified in the fabric softener instructions.
    • Remove all objects from pockets, such as lighters and
    matches.
    • Never use or store flammable materials near to the
    dryer.
    • Never stop a tumble dryer before the end of the
    drying cycle, unless all items are quickly removed and
    spread out so that the heat is dissipated.


    • This appliance is marked according to the European
    directive 2002/96/EC on Waste Electrical and
    Electronic Equipment (WEEE).
    • By ensuring that this product is disposed of correctly,
    you will help prevent potential negative
    consequences for the environment and human
    health, which could otherwise be caused by
    inappropriate waste handling of this product.

    Warning: rear panel may be hot.

    • The dryer is suitable for indoor use only.
    • Do not use extension leads or multiple adaptors.
    5



  • Page 6

    Packaging
    • The packaging box is 100% recyclable, as confirmed
    by the recycling symbol.
    Disposing of packaging and old appliances
    • The dryer is built from reusable materials. The dryer
    must be disposed of in compliance with local waste
    disposal regulations.
    • Before scrapping cut off the power cable so that the
    dryer cannot be connected to the mains.

    on the product or on the
    • The symbol
    documents accompanying the product indicates that
    this appliance must not be treated as household
    waste. Instead it should be handed over to the
    applicable collection point for the recycling of
    electrical and electronic equipment. Disposal must
    be carried out in accordance with local
    environmental regulations for waste disposal.
    • For more detailed information about treatment,
    recovery and recycling of this product please contact
    your local city council office, your household waste
    disposal service or the shop where you purchased
    the product.
    Energy saving tips
    • Always dry a full load, depending on the type of
    laundry and the programme/drying time. For more
    detailed information, see the programme chart.
    • By preference use the maximum spin speed allowed by
    your washing machine, since draining the water
    mechanically requires less energy. You will save time
    and energy when running your drying cycle.
    • Do not overdry the laundry.
    • Clean the lint filter after every drying cycle.
    • Clean the heat exchanger every month.
    • Place your dryer in a room with a temperature
    between 15°C and 20°C. If the temperature is higher
    then ventilate the room, e.g. by opening the window.
    • Always select the correct programme/drying time for
    the load in order to obtain the desired drying results.
    • Select the ‘Gentle’ option only in case of drying small
    loads.
    • When drying cotton, for example, dry Iron Dry and
    Cupboard Dry loads together. Start with the Iron Dry
    programme/drying time setting, remove the laundry to
    be ironed at the end of that cycle and dry the remainder
    of the load on the Cupboard Dry setting.
    6

    • Always set the program selector knob to the “0”
    position after the end of the cycle.



  • Page 7

    ELECTRICAL CONNECTION
    1) For United Kingdom only
    Warning - this appliance must be earthed
    Fuse replacement
    If the mains lead of this appliance is fitted with a BS 1363A 13amp
    fused plug, to change a fuse in this type of plug use an ASTA marked
    fuse, approved to BS 1362 and proceed as follows:
    1. Remove the fuse cover (A) and fuse (B).
    2. Fit replacement 13A fuse into fuse cover.
    3. Refit both into plug.
    Important:
    The fuse cover must be refitted when changing a fuse. If the fuse cover
    is lost, the plug must not be used until a correct replacement is fitted.
    Correct replacements are identified by the colour insert or by the
    colour embossed in words on the base of the plug.
    Replacement fuse covers are available from your local electrical store.

    2) For the Republic of Ireland only
    The information given in respect of United Kingdom will frequently
    apply, but a third type of plug and socket is also used, the
    2-pin type with side earth terminal.

    3) Socket outlet / plug (valid for both countries)
    If the fitted plug is not suitable for your socket outlet, please contact
    Whirlpool Service for further instructions. Please do not attempt to
    change the plug yourself. This procedure must be carried out by a
    qualified Whirlpool technician in compliance with the manufacturer’s
    instructions and current safety regulations.

    7



  • Page 8

    DESCRIPTION OF THE DRYER
    A. Work top
    B. Water container
    C. Contact pin
    D. Door:
    To open the door, pull the handle.
    To close the door, push gently until closed.
    E. Filter
    F. Heat exchanger
    G. Heat exchanger flap

    REMINDER - MAINTENANCE AND CLEANING
    Before cleaning or carrying out maintenance, switch off the dryer.
    AFTER EACH DRYING CYCLE
    • Clean the lint filter at the end of every drying cycle.
    • Empty the water container at the end of each drying
    cycle.

    EACH MONTH
    • Clean the heat exchanger at least every month (see
    “Cleaning the heat exchanger” on the next page).

    CLEANING THE LINT FILTER
    Depending on the model of your dryer, the lint filter can
    have different shapes.
    Clean the lint filter after every drying cycle, or when the
    lint filter indicator lamp lights up, proceeding as follows:
    A. Take the lint filter out of the dryer and carefully open
    the filter.
    B. Carefully remove the complete lint from the lint
    screen.

    A

    A

    B

    B

    When the lint filter is clean, put it back into the dryer.
    Make sure that the lint filter is correctly positioned before
    starting the next drying cycle.

    8



  • Page 9

    CLEANING THE HEAT EXCHANGER
    Before cleaning or carrying out maintenance, switch off the dryer.
    Clean the heat exchanger at least every month, or whenever the heat exchanger indicator lamp
    lights up (optional feature, depending on the model of your dryer), proceeding as follows.
    A. Open the heat exchanger flap and put it to one side.

    A
    B. Turn the two locking bars at the side of the heat exchanger towards the
    middle, to the horizontal position, and pull the heat exchanger out.

    B
    C. Hold the heat exchanger as shown in the picture. Clean it under running
    water by turning it around to reach all sides, especially in front and behind.
    Wipe away dust and lint from the heat exchanger seals and plates.
    Clean the inside of the heat exchanger plates under running water, from
    the front side to the back.

    C
    D. Remove the lint from the heat exchanger housing by hand or with a
    damp cloth. Clean the entire housing from the back to the front side,
    ensuring that all lint is removed.

    D

    • Fully insert the heat exchanger back into the housing (TOP or HAUT mark
    upwards) and lock it again by turning the locking bars back to their original position.
    • The heat exchanger does not need to be dry when it is reinserted after cleaning.
    • Insert and latch the flap again. The flap can only be closed if the heat
    exchanger is correctly positioned.
    • The heat exchanger indicator lamp will switch off automatically when
    you start the next drying cycle.
    The heat exchanger aluminium plates may become discoloured over time,
    depending on the model of your dryer.
    9



  • Page 10

    DRAINAGE SYSTEM
    For your convenience:
    The dryer can be connected directly to the sewage
    system of the house to avoid having to empty the
    water container after each drying cycle.

    C. Connect the hose to the sewage system. The height
    difference between the floor where the dryer is
    positioned and the sewage system connection should
    not exceed 1 m.

    Place an absorbent cloth underneath to collect water
    spillage.
    A. Unplug the hose located at the upper rear part of the
    dryer.

    C

    Notice: To prevent water siphoning back into the
    appliance, the end of the hose must not be immersed in
    the drain water. Avoid bending and twisting the hose.

    A
    B. Remove the hose from the rear protective cover.

    B

    10



  • Page 11

    DOOR REVERSIBILITY
    For your convenience:
    In case you want to stack the dryer on a washing machine, you can
    reverse the door opening direction, to lower the position of the door
    handle.
    Unplug the dryer.

    A

    A. Open the door.

    B. Using a spanner, turn the contact pin (B) in the top part of the door
    through 90° and pull it out.

    B

    C. Remove the door lock:
    Unscrew the 2 screws above and below the door lock system.

    C

    D. Press the small knob above the door lock system with a small
    screwdriver, move the door lock slightly upwards and pull the door lock
    towards you with your finger.

    D
    E. Reverse the door:
    Remove the two screws of the door fixing plate. Fasten the door again
    on the desired side with the 2 screws. Take care to tighten the screws
    horizontally to avoid pinching off the door seal.
    Reposition the door lock:
    Insert the door lock on the opposite side of the door fixing plate. Press
    it fully into the hole and move it downward slightly, until the small knob
    of the door lock system latches in position. Fasten the two screws
    above and below the door lock system.
    Now reinsert the contact pin on the inside of the door, at the top, by
    inserting it and turning it again through 90°.

    E

    NOTE: Ideally you should use a Torx T20 type screwdriver to undo
    and tighten the screws.
    11



  • Page 12

    TROUBLESHOOTING GUIDE/
    AFTER-SALES SERVICE
    In the event that the dryer malfunctions, one of the following failure codes may be displayed.
    Depending on the model of your dryer, the failure may be displayed in letters or by different
    blinking LEDs.
    Failure code

    LED failure code

    Check to be carried out by customer before service call

    F01

    Please call the After-Sales Service.

    F02

    Please call the After-Sales Service.

    F03

    Please call the After-Sales Service.

    F04

    Please call the After-Sales Service.

    F05

    Turn the dryer OFF and unplug it. Make sure that the ambient temperature is
    between 5°C and 35°C. Wait for 1 hour. Plug the dryer back in and restart it. If the
    failure reoccurs, please call the After-Sales Service.

    F06

    Turn the dryer OFF and unplug it. Make sure that the ambient temperature is
    between 5°C and 35°C. Wait for 1 hour. Plug the dryer back in and restart it. If the
    failure reoccurs, please call the After-Sales Service.

    F07

    Please call the After-Sales Service.

    F10 - 15

    Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it. If the failure reoccurs,
    please call the After-Sales Service.

    F18

    Turn the dryer OFF and unplug it. Wait for 1 hour. Plug the dryer back in and restart it. If the failure reoccurs,
    please call the After-Sales Service.

    F19

    Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it. If the failure reoccurs,
    please call the After-Sales Service.

    F20

    Turn the dryer OFF and unplug it. Wait for 1 hour. Plug the dryer back in and restart it. If the failure reoccurs,
    please call the After-Sales Service.

    F21

    Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it. If the failure reoccurs,
    please call the After-Sales Service.

    F22

    Turn the dryer OFF and unplug it. Wait for 5 minutes. Plug the dryer back in and restart it. If the failure reoccurs,
    please call the After-Sales Service.

    Start LED blinks
    Make sure that the door is correctly closed and the heat exchanger correctly positioned. If the failure reoccurs,
    2 times per
    second when please call the After-Sales Service.
    pressed
    Heat exchanger
    LED blinks 2 Make sure that the heat exchanger is correctly positioned. If the failure reoccurs, please call the After-Sales
    times when Start Service.
    button is pressed

    LED not blinking
    12

    LED blinking



  • Page 13

    TROUBLESHOOTING GUIDE/
    AFTER-SALES SERVICE
    If a fault occurs, before contacting our AfterSales Service, perform the following checks to
    try to remedy the problem:
    Drying takes too long / laundry is not dry
    enough:
    • Correct programme selected?
    • Laundry too wet (Washing machine spin speed less
    than 1000 rpm? When the spin speed is less than
    1000 rpm a water container fault may occur during
    the drying cycle).
    • Lint filter clogged (filter indicator lamp on?)
    • Heat exchanger clogged? (refer to the sections
    “CLEANING THE LINT FILTER/CLEANING THE
    HEAT EXCHANGER”).
    • Is the ambient temperature too high?
    • END indicator lamps on? The drying cycle is
    complete and the laundry can be taken out.
    • ‘Gentle’ option selected? The ‘Gentle’ option should
    only be selected with small loads.
    • Mixed laundry load (for example cotton and
    synthetics).

    After-Sales Service
    If, after carrying out the above checks, the
    malfunction persists or reoccurs, turn the
    dryer off and call the After-Sales Service
    (refer to warranty).
    Please specify:
    • The nature of the fault.
    • The dryer type and model.
    • The service code (the number after the word Service
    on the adhesive rating plate) on the lower side of the
    door opening.
    • Your full address and phone number.

    The dryer does not operate:
    (after a power failure and/or interruption to the
    mains supply, always press the “Start (Pause)”
    button).
    • Plug connector properly inserted into the mains
    electricity socket?
    • Power failure?
    • Fuse blown?
    • Door properly closed?
    • Drying programme selected?
    • Start delay option selected?
    • “Start (Pause)” button activated?
    • Indicator lamps are lighting up?

    Lint filter, water container or heat exchanger
    indicator lamp on:





    Lint filter clean?
    Water container empty?
    Water container correctly positioned?
    Heat exchanger clean and correctly positioned?

    Water droplets underneath the dryer:






    Heat exchanger correctly positioned?
    All lint on the heat exchanger seal removed?
    All lint on the door seal removed?
    Water container positioned correctly?
    Dryer levelled?
    13






Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Whirlpool AWB 888 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Holen Sie sich Ihr Benutzerhandbuch per E-Mail

Geben Sie Ihre E-Mail-Adresse ein, um das Handbuch zu erhalten von Whirlpool AWB 888 in der Sprache / Sprachen: Englisch als Anhang in Ihrer E-Mail.

Das Handbuch ist 2,32 mb groß.

 

Sie erhalten das Handbuch in Ihrer E-Mail innerhalb von Minuten. Wenn Sie keine E-Mail erhalten haben, haben Sie wahrscheinlich die falsche E-Mail-Adresse eingegeben oder Ihre Mailbox ist zu voll. Darüber hinaus kann es sein, dass Ihr ISP eine maximale Größe für E-Mails empfangen kann.

Andere Handbücher von Whirlpool AWB 888

Whirlpool AWB 888 Kurzanleitung - Deutsch - 6 seiten

Whirlpool AWB 888 Bedienungsanleitung - Deutsch - 12 seiten

Whirlpool AWB 888 Kurzanleitung - Englisch - 6 seiten

Whirlpool AWB 888 Kurzanleitung - Holländisch - 6 seiten

Whirlpool AWB 888 Bedienungsanleitung - Holländisch - 11 seiten

Whirlpool AWB 888 Kurzanleitung - Französisch - 6 seiten

Whirlpool AWB 888 Bedienungsanleitung - Französisch - 11 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info