Whirlpool is a registered trademark of Whirlpool USA.
Programme
Tempe-
rature
(°C)
Load
(kg)
Water
(l)
Energy
without “Rapid”
(kWh)
Approx. Programme Duration (hrs : min)
without “Rapid”with “Rapid”
Cotton/Antibacterial955.049*1.701:551:45
Cotton605.0470.952:201:45
Cotton405.0470.642:051:30
Jeans404.0410.581:44–
Synthetics603.050*0.902:051:14
Synthetics403.0400.501:500:59
Delicates401.5500.550:45–
Delicates301.5500.500:41–
Daily load403.0400.451:00–
Speed 15’303.0300.150:15–
Wool/Handwash401.0400.550:35–
Wool/HandwashCold1.0400.100:30–
eCotton **605.0470.753:10–
eCotton **602.5320.682:00–
eCotton405.0470.652:00–
eCotton **402.5320.561:45–
1.
ADD DETERGENTS, CLOSE THE LID AND
SELECT THE PROGRAMME
Load the machine, close the drum doors and check
that they are properly locked.
2. Add detergent and eventual additives as described on
the front page and in your Instructions for use.
3. Close the lid.
4. Turn the programme selector to the desired
programme and temperature. The indication next
to the “Start/Pause” button blinks. The indication
lamp of the predefined spin speed lights up.
If you do not start the programme soon after having
made your choice, the washing machine will switch off
automatically after about a quarter of an hour. Switch on
the washing machine again by turning the programme
selector back to „Off/O“ and then to the desired
programme.
SELECT ANY DESIRED OPTION
Push the button(s) of any option(s) desired - the
respective indication lights up. When the combination
of programme and additional option(s) is not possible,
the indication lights switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Prewash” button
•Only for heavily soiled loads (for example
sand, granular dirt). Increases the cycle time by
approximately 15 min.
•Do not use liquid detergent for the main wash when
activating the Prewash option.
“Rapid” button
•Enables quicker washing by shortening the
programme duration.
•Recommendable for small loads or only lightly soiled
laundry.
“Intensive rinse” button
•More water is added and rinse cycle is prolonged.
•This option is particularly suitable for areas with very
soft water, washing baby linen and helping people
with allergies.
“Rinse hold” button
•The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing
and prevent colours from changing.
•It is particularly useful if you want to postpone
spinning to a later time, or if you want to drain only.
•If you select “Rinse hold”, do not leave items to soak
for too long.
Note: The programme stops to “Rinse hold” at
the time the “Rinse hold” light in the programme
sequence indicator is on. The indication lamp next to
the “Start/Pause” button blinks.
Terminate the “Rinse hold” option:
•Press the “Start/Pause” button; the programme will
terminate automatically with the final spin cycle for
the present wash programme.
•If you do not wish to spin the clothes, turn the
programme selector to “Drain programme and press
the “Start/Pause” button.
“Spin” button
•Every programme has a predefined spin speed.
•Press the button to set another spin speed.
•If spin speed “0” is selected, the final spinning is
cancelled but intermediate spin peaks remain during
the rinse. The water is drained out only.
START DELAY
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is cheaper. Do not use liquid detergent when
activating the “Start delay”.
•Select programme, spin speed and options.
•Press the “Start Delay” button several times to
select a delay time of 1, 3, 6, 9 or 12 hours. The
corresponding indicator lamp lights up.
•Start the programme (see “Progremme Start”). The
indication next to the “Start delay” button lights up
and goes off when the programme starts.
•Once having pressed the “Start/Pause” button,
the countdown of the time delay begins. When the
programme starts, the start delay indicator light
goes off and is replaced by the programme sequence
indication.
•After the “Start/Pause” button has been pressed,
the number of hours preselected can be changed by
pressing again the “Start delay” button.
To cancel the “Start delay”
..before you press the “Start/Pause” button:
•Turn the programme selector to another position or
press the “Reset” button.
..after having pressed the “Start/Pause” button:
•Press the “Reset” button for at least 3 second. The
start delay indicator light goes off.
PROGRAMME START
Open the tap and press the “Start/Pause” button.
The indication lamp next to the “Start/Pause” button
lights up. The programme sequence indicator shows the
current programme phase, running from left to right
through Wash, Rinse, Spin/Drain. When the programme
phase is finised, the corresponding indication goes out.
•Note: If there is a power interruption or if the
appliance is disconnected during the cycle, the
programme will run again from the point where it
was interrupted.
Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. Consumption data in the home may vary with
respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.Water and energy consumption refer
to the default setting of the programmes; selecting special options or modifying spin speed or temperature will change the consumption data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
* To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
** Standard Cotton programme and basis for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
CONSUMPTION DATA
Power consumption in off-mode 0.11 W / in left-on mode 0.11 W
“LID OPEN” INDICATION
Before starting and after end of a programme, the lamp
lights to show the the lid can be opened. As long as a
wash programme is running, the lid remains locked and
must on no account be forced open. In case you have
an urgent need to open it during a running programme,
refer to “Cancel a running programme before the end”.
FAILURE INDICATIONS
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
“Water tap closed”
No or not sufficient inlet water.
“Service”
Failure or malfunction of an electrical component.
“Clean pump”
Waste water is not pumped out.
•
PROGRAMME END
The “Lid open” indicator lights up. After about a
quarter of an hour, the washing machine will switch
off completely to save energy.
1. Turn the programme selector to the “Off/O”
position.
2. Close the water tap.
3. Open lid and drum and unload the machine.
4. Leave the lid open for some time to allow the interior
of the machine to dry.
1.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
Press the “Start/Pause” button to pause the
programme. The light blinks.
2. Select the new programme, temperature, any
options and another spin speed if you want.
3. Press the “Start/Pause” button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add
detergent for this programme.
CANCEL A RUNNING PROGRAMME BEFORE
THE END
The “Reset” button cancels a programme before the
end.
•Press the “Reset” button for at least 3 seconds. Any
existing water is drained out before the door can be
Ich habe eine AWE 5125 Waschmachine von Whirpool , nun zeigt sie an Pumpe reinigen habe ich noch nie gehabt! Wie mache ich das und wo befindet sich die Pumpe. Es ist noch Wäsche in der Maschine in Waschlauge, da nicht abgepumpt werden kann... Wäre Ihnen für eine schnelle hilfreiche Antwort sehr dankbar. Edith Midunsky
Eingereicht am 23-7-201714:59
Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.
Art des Missbrauchs:
Forenregeln
Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:
Lesen Sie zuerst die Anleitung;
Schauen Sie nach, ob die Frage bereits gestellt wurde;
Stellen Sie die Frage so deutlich wie nur einigermaßen möglich;
Erwähnen Sie was Sie bereits versucht haben um das Problem zu lösen;
Ist Ihr Problem von einem Besucher gelöst dann lassen Sie ihn / sie wissen in diesem Forum;
Falls Sie reagieren möchten, so verwenden Sie bitte das Antworten- Formular;
Da ihre Frage für alle Besucher sichtbar ist, sollten Sie lieber keine persönliche Daten erwähnen.
Neu registrieren
Registrieren auf E - Mails für Whirlpool AWE 5125 wenn:
neue Frage gestellt werden
neue Handbücher vorhanden sind
Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.
Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.
Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.
Ihre Frage wurde zu diesem Forum hinzugefügt
Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.
