Bedienungsanleitung Whirlpool awg 912 d (Seite 2 von 2) (Englisch)

314433

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 20135

Whirlpool is a registered trademark of Whirlpool USA

Add detergent as indicated on the front page and as

described in the chapter “Detergent and Additives”

in the Instructions for Use.

1. Turn the

programme selector

to the desired

programme.

2. The indicator of the predefined

spin speed

lights up; in case you want to set another spin

speed, press the “Variable spin” button.

Press the button(s) of any required option(s) - the

respective indicator lights up.

When the combination of programme and

additional option(s) is not possible,

the indicators switch off automatically. Unsuitable

combinations of options are deselected automatically.

“Prewash” button

• Only for heavily soiled loads (e.g. sand, granular dirt).

Increases the cycle time by approx. 15 minutes.

• Do not use liquid detergent for the main wash

when activating the prewash option.

“Intensive rinse” button

• More water is added and the rinse cycle is

prolonged.

• This option is particularly suitable for areas with

very soft water, washing baby linen, and helps

people with allergies.

“Easy Ironing” button

• Can be used together with “Cotton”, “Synthetic”

and “Daily load” programmes to make ironing easier.

• Increases the water quantity and the clothes are

spun very gently.

“Rinse hold” button

• The laundry remains in the last rinse water

without the final spin cycle, to avoid creasing and

prevent colours from changing.

• This option is particularly recommended for the

“Synthetics”, “Daily load” or “Delicates”

programmes.

• It is particularly useful if you want to postpone

spinning to a later time, or if you want to drain only.

• If you select “Rinse hold”, do not leave the

laundry to soak for too long.

Note:

The programme stops to “Rinse hold” at

the time the “Rinse Hold” light in the programme

sequence indicator is on. The indicator next to

the

“Start”

button flashes.

To terminate the “Rinse hold” option:

•Press the

“Start”

button; the programme will

terminate automatically with the final spin cycle

for the preset wash programme.

“Variable spin” button

• Every programme has a predefined maximum

spin speed.

• Press the button to set another spin speed.

• If spin speed “00” is selected, the final spin is

cancelled but intermediate spin peaks remain

during rinse. The water is drained out only.

CONSUMPTION DATA

Programme

Te m p e r a t u r e

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. programme duration

(hours : minutes)

White Cotton / Antibacterial 90 5.0 52

1.70 2:10

Cotton 75 5.0 52 1.33 2:05

Cotton with “Eco”

***

60 5.0 49 0.95 2:15

Cotton 40 5.0 62 0.51 2:00

Synthetics 60 2.5 46

0.80 1:40

Synthetics 40 2.5 46 0.46 1:35

Daily load 40 3.5 52 0.30 1:25

Quick wash 35 2.5 30 0.40 0:40

Delicates 30 2.5 54 0.24 0:45

Wool 40 1.0 56 0.44 0:54

Handwash 30 2.0 65 0.24 0:57

Consumption values were measured in normalized conditions in compliance with standard IEC/EN 60 456. In domestic use, consumption

data may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

The time indicated on the display (if present) can deviate from the values in the table, because it takes into account the household

conditions applicable at that time.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

***

Reference programme for energy label.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

The “Start Delay” option allows you to programme

machine activation at a later stage, for example at

night when electricity is cheaper. Do not use liquid

detergent when activating the “Start delay”.

• Select the programme and options.

• Press the “Start Delay” button to select

programme start a delay time of 1 to 16 hours;

•Press the

“Start”

button.

The indicator next to the

“Start delay”

button

lights up, whereas the selection made is shown

on the display.

Its flashing indicates the countdown of the

remaining time.

• At the end of the delay time the machine starts

the set programme. The icon indicating the wash

cycle step being carried out at that moment is

displayed.

• After pressing the

“Start”

, the number of hours

preselected can be reduced by pressing and

holding the “Start Delay” button.

To cancel the “Start Delay”:

Press the

“Start delay”

button until the time

indicated on the display is “00”; the selected

programme will then start.

Open the tap and press the

“Start”

. The indicator

next to the

“Start”

button lights up.

At the end of a programme, the message “End”

appears on the display, indicating that the door can

be opened. As long as a wash programme is running,

the door remains locked and must not be forced

open. In case you have an urgent need to open it

during a running programme, refer to “Cancel

(Reset) a running programme before the end”.

E02-E03 “Service”

The display of this “Service” code can be due to a

faulty electrical component. Refer to the

“Troubleshooting guide” in the Instructions for Use;

If the fault persists, contact the After-Sales Service.

E01 “Pump cleaning”

The water is not discharged. Check if the drain hose

is bent or if the filter requires cleaning; in the latter

case, refer to the Instructions for Use (“Removing

the filter”).

E00 “Water tap closed”

The washing machine water feed is insufficient or

lacking. Open the tap; Turn the programme

selector to “Off/O” and reset the programme. If the

fault remains displayed, consult the

“Troubleshooting guide” in the Instructions for Use.

E04 “Door lock”

The display of this code could be due to the door

not being properly closed. Try closing it again. Turn

the programme selector to “Off/O” and reset the

programme. If the fault remains displayed, consult

the “Troubleshooting guide” in the Instructions for

Use.

• At the end of the wash cycle, the message

“END” will appear on the display, indicating

that the door is unlocked.

1. Turn the programme selector to the “Off/O”

position.

2. Close the water tap.

3. Open the door and remove the washing.

4. Leave the door ajar to allow the drum to dry.

1. Turn the programme selector to “Off/O”.

2. Select the new programme, any options and

another spin speed if you want.

3. Press the

“Start”

button again. The new

programme resumes the wash programme

from where the previous one was interrupted.

Do not add detergent for this programme.

• Reset by turning the programme selector to

“Off/O” and select the “Drain Spin”

programme to remove the water remaining in

the bowl before the door can be opened.

START DELAY

PROGRAMME START

“DOOR OPEN” INDICATOR

DISPLAY ALPHANUMERIC INDICATIONS

END OF WASH CYCLE

CHANGING PROGRAMME AND/OR

OPTIONS AFTER PROGRAMME START

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

30120135GB.fm Page 2 Tuesday, September 18, 2007 9:47 AM

Black process 45.0° 150.0 LPI

Whirlpool awg 912 d Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool awg 912 d

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info