Bedienungsanleitung Whirlpool awm 019 (Seite 12 von 13) (Englisch, Holländisch)

306081

Zoom out

Zoom in

Vorherige Seite

1/13

Nächste Seite

What should I do when the automatic safety system detects a malfunction?

(

varies depending on model)

The programme is interrupted and various indicators (if available) point to the source of the fault.

Fault description table

a. Water inlet fault (no or insufficient water supply)

For models with a fault display, the “Water Tap

Closed” indicator is on or the display alternately

shows “FH”. Switch off the appliance by turning

the programme selector to the “Off/0” position

and unplug it.

For models with no fault display, the washing

machine stops in the appropriate step. Switch off

the appliance and unplug it.

Check whether:

•

the water tap is completely open, and the water

supply pressure is sufficient;

•

the water inlet hose is kinked;

•

the mesh filters are blocked (see “Care and

Maintenance”/“Water Hose Mesh Filters”);

•

the water inlet hose is frozen.

Reconnect the appliance to the electrical supply.

For models with a fault display, reselect the desired

programme and press the

“Start/Pause”

button

again to continue with the programme (do not add

detergent for this programme).

For models without a fault display continue the

programme by pressing the

“On/Off”

button

again (do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

b.Draining out fault

For models with a fault display, depending on the

model, the display shows statically or alternately

“FP”. If a “Clean pump” indication is fitted, the red

indication next to it lights up. Switch off the

appliance by turning the programme selector to

the “Off/0” position and unplug it.

For models with no fault display, the washing

machine stops in the appropriate step. Switch off

the appliance and unplug it.

Check whether:

•

the drain hose is kinked (see “Installation Guide”);

•

the pump / filter is blocked (see “Removing the

Filter / Draining Residual Water”);

IMPORTANT

: before draining, allow the wash

water to cool down.

•

the drain hose is frozen.

Connect the appliance to the electrical supply.

For models with a fault display reselect the desired

programme and press the

“Start/Pause”

button

again to continue with the programme (do not add

detergent for this programme).

For models without a fault display continue the

programme by pressing the

“On/Off”

button

again (do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service

(see “After-Sales Service”).

c. Electrical module fault

For models with a fault display “F4” to “F19” are

displayed and some or all Spin Speed Selection

indications are flashing. Switch off the appliance.

Select a programme and press the

“Start/Pause”

button once again. The programme will continue.

For models without a fault display the washing machine

stops in the appropriate step. Switch the appliance first

off, then on. The programme will continue.

If the fault re-occurs, contact After Sales Service

(See “After-Sales Service”).

d.Water Stop fault

(if available)

The “Water Stop” may have been triggered by:

too much foam.

a leak in the inlet hose or in the appliance.

In this case the pump is switched on automatically

in order to pump the water out.

For models with a fault display, the “Water Stop”

indication lights up. The display shows “FA” or

alternately “F” and “A” and the pump is running.

Switch off the appliance by turning the programme

selector to the “Off/0” position, unplug the appliance

and make sure that the water tap is closed.

For models without a fault display the washing

machine stops in the appropriate step. Switch off

the appliance, unplug the appliance and make sure

that the water tap is closed.

Tilt the appliance forwards carefully to allow the

collected water to flow out.

Then:

plug in the appliance,

turn the water tap on (if water immediately flows

into the appliance again, without the appliance

being started, close water supply and call After-

Sales Service).

For models with a fault display reselect the desired

programme and press the

“Start/Pause”

button

again to continue with the programme (do not add

detergent for this programme).

For models without a fault display continue the

programme by pressing the

“On/Off”

button again

(do not add detergent for this programme).

If the fault re-occurs, contact After-Sales Service (see

“After-Sales Service”).

Small indication lights up Digital display Fault description

“Water Tap Closed” “FH” “Water inlet fault”

“Clean pump” “FP” “Draining fault”

- from “F15” to “F19” “Electrical components fault”

“Water Stop” “FA” “Water Stop fault”

3gb05612.fm Page 68 Saturday, June 5, 2004 4:16 PM

Black process 45.0° 100.0 LPI

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Whirlpool awm 019 Seite 12

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info