5019 301 15172
Whirlpool is a registered trademark of Whirlpool USA
Prewash cycle increases programme duration by approximately 1 5 min. Consumptio n values were meas ured in
normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home may vary with respect
to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.
*
The remaining time indicator can deviate from the value s in the table, because it takes into account the operating
conditions applicable at that time.
**
T o reduce the water temperature, some cold water is added at the end of th e main wash cycle, before the pump
drains the water out.
***
Reference programme for energy label.
Add the detergent as described in the programme
table or in the chapter “Detergent and Additives” of
the Instructions for Use.
1. Turn the
programme selector kn ob
to the
desired programme.
2. The remaining time display shows the duration of
the chosen programme (in h ours and minutes) and
the pilot lamp of the
“Start/Pause”
button flashes.
3. The indica tor of the predefined s pin speed
corresponding to the sel ected programme lights
up. The recommended temperature (see
indicator) can be altered by pressing the “
+
” or
“
–
” button.
Selecting any option the indication lights up.
When the combination of programme,
additional options and t emperature is not
possible, the indication lights switch off
automatically and a signal sounds.
“Easy ironing” button
• Can be used together with all programmes to
reduce creasing.
• Increases the water quantity and the clothes are
spun ve ry gently .
“Pre wash” button
• Only for heavily soiled laundry (e.g. sand, granular
dirt). The cycle time increases by approx. 15 minutes .
“Extra rinse” button
• More water and a longer time in rinse cycle is added.
• This option is particularly suit able for areas with
very soft water , for baby clothes and to help
people with allergies .
“Rinse hold” button
• The laundry rem ains in the last rins e water
without being spun: this prevents creasi ng and
colours from changing.
• This option is particularly recom mended for the
programme “Synthetics” or “Delicate”.
• This function is particularly useful if you want to
postpone spinning to a later time, or if you want
to drain only .
Note:
The programme starts to “Rinse hold” as
soon as the “Rinse hold” light in the programme
sequence indicator lights up.
T erminate the “Rinse hold” option :
• Press the “Rinse hold” button again; the
programme will terminate automatically with the
final spin cycle for the presen t wash programme.
• If you do not wish to spin the clothes, press the
“Reset/Unlock do or ” button. The water is drained
out then, before the door can be opened.
CONSUMPTION DATA
Programme
T emperature
Selector
(°C)
Load
(kg)
Wa t e r
(l)
Energy
(kWh)
Approximate programme
duration
*
(hours : minutes)
Cotton / Antibacterial 95 9.0 95
**
2.70 2:40
Colours
***
60 9.0 81 1.53 2:40
Colours 60 4.0 50 1.10 1:35
Colours 40 9.0 81 0.90 2:25
Synthetics 40 4.0 52 0.60 1:30
Daily load 40 4.0 50 0.60 1:00
Rapid plus 30 4.0 35 0.40 0:30
Delicate 30 2.5 65 0.45 0:50
W ool 40 2.0 60 0.50 0:35
Handwash 30 2.0 60 0.30 0:31
Big items 40 2.5 85 0.80 1:30
ADD DETERGENT, CLOSE THE DOOR AND
SELECT THE PROGRAMME
SELECT ANY DESIRED OPTION
“ V ariable spin” button
• Every programme has an automatic predefined
spin speed.
• Press the button to set another spin speed.
• If spin speed “0” is selected, the final s pinning is
cancelled but intermediate spin peaks remain
during rinse. The water is drained out only .
The “Start delay” allows to run the machine at the
consumer’s convenience, for example at night when
electricity is c heaper.
• Select progra mme, temperature and options.
• Press the “Start delay ” button to select the delay
time by 1 to 23 hours;
•P r e s s t h e
“Start/P ause”
button.
• The time delay indication disappears when the
programme starts and i t is replaced by the
remaining time.
• The number of hours preselected ca n later be
reduced pressing again the “Start delay ” button.
To cancel the “Start delay”.
• T urn the programme selector to the “ ” position.
• Reselect the desired programme and options
and press the
“Start/P ause”
button.
Turn on the tap and press the
“Start/Pause”
button.
The pilot lamp of the
“Start/Pause”
button lights up.
The indicator lamps show the sequence reache d in
the programme. After starting the programme, the
sequence indication runs from top to bottom
through Prewash, Wash, Ri nse, Spin.
When a sequence of the programme is finished th e
corresponding lam p goes out.
Each time a programme starts the door is locked, the
“Door locked” indication light comes on and approx.
0.5 litres of water enters the machine. In the
programmes Cotton / Antibacterial, Colo urs,
Synthetics, Daily load and Rapid plus, for 10 minutes at
the beginning of the Main Wash the programme can be
interrupted by pressing the
“Start/Pause”
button and
the door can be opened again, e.g. to add more
washing. After th is time, the door re mains locked until
the end of the programme and must on no account be
forced open. You will find more information about
door locking in the Instructions for Use.
• The time remaining is “0:00” and the “End” light
is on.
1. Turn the programme selector knob to the “ ”
position.
2. Turn the tap off and leave the door ajar to allow
the drum to dry.
1. Press th e
“Start/Pause”
button to interrupt
the programme. The light flashes.
2. Select the new programme (with temperature),
any options and another spin speed if you want.
3. P re ss t he
“Start/Pause”
button again. The new
programme conti nues at the same position where
the previous programme was interrupted. Do not
add detergent for this programme.
Press the “Res et/Unlock door” button for a t least 3
seconds. Any existing water is drained out before
the door can be opened. Caution, the washing co uld
still be hot!
Detailed information can be found in the
instructions for use .
The controls can be locked to avoid interference by
children.
1. If the machine is off:
Turn the programme selector knob from the
“0” position to any programme. Do not press
the
“Start/Pause”
button. Press the “Child
lock” button for 5 seconds. The “Child lock”
indicator lights up. Turn the progr amme
selector knob to the OFF position “ ” again.
2. While a programme is running:
Press the “Chil d lock” button for 5 seconds.
The child lock indicator will light up.
Now, in spite of the programme selector knob
being turned, no programme can be started or
altered. However, a running programme can be
stopped at any time (e.g. in an emergency), by
turning the programme selector knob to “ ”.
Attempts at changing during the running programme
are signalled by the lamp of the accidentally chosen
programme flashing . The indicator light for the actual
programme running lights up.
To unlock the controls, the machine must either
have a programme running or be in select mode.
Press the “Child lock” button for 5 seconds. The
child lock lamp will go out.
START DELAY
PROGRAMME START
ADD W ASHING/DOOR LOCK
PRO GR AM ME EN D
CHANGE THE PROGRAMME,
TEMPERATURE, OPTIONS AFTER
PROGRAMME START
RES ET / UN LO CK DO O R B UT T ON
CHILD L OCK