Bedienungsanleitung Whirlpool AWO 164U2 - 6TH SENSE (Seite 2 von 2) (Englisch)

574748

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

Whirlpool is a registered trademark of Whirlpool USA

4000 107 24361

Load the laundry, close the door and add detergent as indicated

on the front page and as described in the chapter “Detergent and

Additives” in your Instructions for Use.

Turn the programme selector to the desired programme and

temperature.

The display shows the programme duration and the predefined

spin speed. The “Start/Pause” indicator blinks.

The washing machine is designed to save energy, therefore, if

you have selected a programme but do not start it within about

a quarter of an hour, it will switch off automatically.

To switch it on again, turn the programme selector to “Off/O” and

then to the desired programme again.

Push the button of any option desired - the indicator lights up.

If the combination programme/option or option/option is not

possible, the indicator switches off automatically.

“Colours 15° button

• Saves energy used for water heating while maintaining a

good wash result.

• Supports colour maintenance when washing coloured laundry.

• Recommendable for lightly soiled laundry without stains.

• Make sure that your detergent is suitable for cold wash

temperatures (15 or 20°C).

• Not selectable for Cotton 95 °C.

“Rapid” button

• Enables quicker washing by shortening the programme duration.

• Recommendable for only lightly soiled laundry.

• Not selectable for Cotton 95 °C.

“Clean +” button

• Choose this option if you use an in-wash additive for stain

removal (powder, for example “Vanish”) - it will optimize the

additive’s efficiency to get better wash performance and

stain removal.

• Use with maximum load.

• Add an appropriate amount of in-wash additive for stain

removal (powder) to the main wash chamber, together with

your detergent (only use powder detergent with this option).

Respect the manufacturer’s dosing instructions.

• May prolong the programme by up to 15 minutes.

• Appropriate for use of stain removers and bleaches on oxygen

basis. Chlorine or perborate bleaches must not be used!

“Prewash” button

• Adds a prewash cycle to the wash programme selected;

prolongs the programme by about a quarter of an hour.

• Recommended for heavily soiled laundry (e.g. with sand or

granular dirt).

• Do not use liquid detergent for the main wash when

selecting “Prewash”.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• Particularly suitable for areas with very soft water, washing

baby linen and helping people with allergies.

“Easy ironing” button

• Reduces creasing by an increased water quantity and a very

gentle spin.

CONSUMPTION DATA

Power consumption: in off-mode 0.16 W / in left-on mode 0.16 W.

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

Approximate remaining moisture

content (%) ****

without “Rapid” with “Rapid”

1000 rpm

RMC C

1200 rpm

RMC B

1400 rpm

RMC B

Mixed 40 4.0 46 0.40 1:00 — 68 59 55

Cotton 95 6.0 74** 2.20 2:40 — 68 59 55

Cotton 60 6.0 50 1.10 2:20 1:45 68 59 55

Cotton 40 6.0 64 0.70 2:05 1:15 68 59 55

Synthetics 40 3.0 42 0.40 1:20 0:55 45 40 35

Delicates 30 1.5 60 0.40 0:46 —

Wool/Handwash 40 1.0 45 0.55 0:40 —

White 60 6.0 66 1.34 2:37 —

Light colours 40 4.0 50 0.45 1:20 —

Dark 30 4.0 40 0.43 1:40 1:15

Cotton *

60 6.0 41 0.86 4:00 — 625353

Cotton *

60 3.0 30 0.57 3:00*** — 625353

Cotton *

40 3.0 30 0.55 3:00*** — 625353

Speed 15 30 3.0 20 0.15 0:15 —

Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual

water supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx.

15 °C through the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water

supply will lower the energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature.

Water and energy consumptions refer to the default setting of the programmes, with temperature and load as indicated in the table; selecting any options

or changing the spin speed will also change the consumption data.

The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also

“Troubleshooting Guide” in your Instructions for Use).

** To reduce the water temperature, some cold water is added at the end of the main wash cycle before the water is drained.

*** Automatic adaptation of programme duration after detection of wash load.

**** After programme end and spinning with maximum selectable spin speed, in default programme setting.

* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.

LOAD LAUNDRY, ADD DETERGENT AND

SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

“Rinse hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing and

prevent colours from changing.

• Particularly useful if you want to postpone spinning to a later

time, or if you want to drain only.

• The programme stops to “Rinse hold” at the time the “Rinse

hold” indicator on the display blinks. The “Start/Pause”

indicator blinks as well.

Terminate the “Rinse hold” option :

• Press the “Start/Pause” button ; the programme will

terminate automatically with the final spin cycle for the

present wash programme.

• If you do not wish to spin the clothes, turn the programme

selector to the “Drain” programme and press the “Start/

Pause” button to start draining.

“Spin” button

• Every programme has a predefined spin speed; press the

button to set another spin speed.

• If spin speed “0” is selected, the final spinning is cancelled

and the water is drained only. However, intermediate spin

phases remain during rinse.

With this function you can postpone your programme to

complete at a later time: press the button to select in how many

hours the programme shall be finished. Thus, it allows you to

have your laundry ready at a particular time and to profit from

more favourable energy rates during the night, for example.

Do not use liquid detergent when activating the “Cycle end”

button.

• The time until the cycle end can be selected in full hour time

segments (1 to 24 h). When you press the button, the shortest

possible time will be displayed; keep on pressing the button to

loop through all the available times. To remove it again, keep

on pressing the button until you see the value “0:00”.

• When you have selected the desired time until the cycle end,

press “Start/Pause” - the countdown will begin.

• During the countdown, you can still modify the programme

setting (select or deselect options, change spin speed etc.).

If the modifications prolong the programme duration so that

it overruns the originally set time until the cycle end, the

programme will start immediately.

• Sometimes the programme may finish before the selected

time until the cycle end has expired (e.g. for small loads).

In this case, the washing machine will tumble the laundry

regularly to keep it fresh, until the selected “Cycle end” time

has expired. During tumbling, the display will show an

animation. The tumbling phase can be stopped at any time

either by pressing any button or by rotating the programme

selector; the animation will stop and the door will unlock in

about 1 minute as indicated on the display.

The “Eco monitor” gives you a rough feedback about the power

consumption of the programme setting you selected.

As soon as you turn the programme selector to any programme,

the “Eco monitor” is on.

The indicator on the left is to show that the “Eco monitor”

is active. The four indicators next to it show the degree of

consumption: the less power your programme setting is

forecasted to consume, the less indicators will light up.

This depends on the programme, temperature and options

selected, and also on the size of the wash load. For that reason,

the forecasted degree of power consumption may adapt when

the washing machine detects the wash load.

Open the water tap and press the “Start/Pause” button .

The “Start/Pause” indicator lights up.

When the laundry load is detected or the programme duration is

updated, an animation appears on the display.

Before starting and after end of a programme, the indicator lights to

show that the door can be opened.

As long as a wash programme is running, the door remains locked

and must on no account be forced open. In case you have an urgent

need to open it during a running programme, refer to “Reset a

running programme”.

If one of the failure indicators blinks, consult the

“Troubleshooting Guide” in your Instructions for Use.

“Water tap closed”: no or not sufficient inlet water.

“Service”: failure or malfunction of an electrical component.

“Clean pump”: waste water is not pumped out.

Spin speed blinks: unbalance during spinning.

• The “Door open” indicator lights up, and the display

shows “End”. After about a quarter of an hour, the washing

machine will switch off completely to save energy.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press the “Start/Pause” button to pause the

programme. The indicator blinks.

2. Select the new programme and, if you want, another spin

speed and any options.

3. Press the “Start/Pause” button again. The new

programme continues at the same position where the

previous programme was interrupted. Do not add

detergent for this programme.

The “Reset” button cancels a programme before the end.

•Press and hold the “Reset” button for a few seconds.

The water is drained. It may last some time until the door

can be opened.

SET CYCLE END

ECO MONITOR

less more

PROGRAMME START

“DOOR OPEN” INDICATOR

FAILURE INDICATORS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

RESET A RUNNING PROGRAMME

- the sensor technology adapts drum movement, water, energy and programme duration to your wash load

Whirlpool AWO 164U2 - 6TH SENSE Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool AWO 164U2 - 6TH SENSE

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info