Bedienungsanleitung Whirlpool awo 447 (Seite 2 von 2) (Englisch)

308281

Zoom out

Zoom in

Vorherige Seite

1/2

Nächste Seite

5019 301 06243

Whirlpool is a registered trademark of Whirlpool USA

Add detergent as indicated on the front page and as

described in the chapter “Detergent and Additives” in

your Instructions for Use.

Close the door and turn the programme selector to the

desired programme and temperature. The indication lamp

next to the

“Start (Pause)”

button blinks and the

indication lamp of the predefined spin speed lights up.

Push the button(s) of any option(s) desired - the respective

indication lights up.

When the combination of programme and additional

option(s) is not possible, the indication lights switch off

automatically. Unsuitable combinations of options are

deselected automatically.

“Prewash” button

• Only for heavily soiled loads (for example sand,

granular dirt) sensible. Increases the cycle time by

approximately 15 min.

• Do not use liquid detergent for the main wash when

activating the Prewash option.

“Eco” button

• With a modified temperature profile and a slightly

prolonged washing duration, the optimum

combination of excellent washing result and even

lower energy consumption is achieved.

“Intensive rinse” button

• More water is added and rinse cycle is prolonged.

• This option is particularly suitable for areas with very

soft water, washing baby linen and helps people with

allergies.

“Rinse hold” button

• The laundry remains in the last rinse water without

progressing to the final spin cycle to avoid creasing and

prevent colours from changing.

• This option is particularly recommended for the

programmes “Synthetics”, “Daily load” and

“Delicates”.

• It is particularly useful if you want to postpone spinning

to a later time, or if you want to drain only.

• If you select “Rinse hold” do not leave items to soak

for too long.

Note:

The programme stops to “Rinse hold” at the

time the “Rinse hold” light in the programme sequence

indication is on. The indication lamp next to the

“Start

(Pause)”

button flashes.

Terminate the “Rinse hold” option:

• Press the

“Start (Pause)”

button; the programme

will terminate automatically with the final spin cycle for

the present wash programme.

• If you do not wish to spin the clothes, turn the

programme selector knob to the “Drain” programme

and press the

“Start (Pause)”

button.

CONSUMPTION DATA

Programme

Temperature

(°C)

Load

(kg)

Water

(l)

Energy

(kWh)

Approx. Programme Duration

(hours : minutes)

Cotton 95 6.0 59

1.90 2:00

Cotton with “Eco”

60 6.0 49 1.02 2:10

Cotton 40 5.0 56 0.70 2:00

Synthetics 60 2.5 50

0.80 1:35

Synthetics 40 2.5 46 0.50 1:20

Delicates 30 1.5 60 0.50 0:45

Daily load 40 3.0 41 0.50 1:00

Quick wash 30 3.0 41 0.40 0:30

Wool 40 1.0 60 0.50 0:45

Handwash 40 1.0 45 0.50 0:40

Handwash 30 1.0 45 0.40 0:36

Consumption values were measured in normalized conditions in compliance with Standard IEC/EN 60 456. Consumption data in the home

may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type of wash.

To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.

Reference Programme for Energy Label.

ADD DETERGENTS, CLOSE THE DOOR

AND SELECT THE PROGRAMME

SELECT ANY DESIRED OPTION

“Variable spin” button

• Every programme has a predefined spin speed.

• Press the button to set another spin speed.

• If spin speed “0” is selected, the final spinning is

cancelled but intermediate spin peaks remain during

rinse. The water is drained out only.

The “Start Delay” allows to run the machine at the

consumer’s convenience, for example at night when

electricity is cheaper. Do not use liquid detergent when

activating “Start delay” option.

• Select programme, temperature and options.

• Press the “Start Delay” button to select the delay time

by 1, 3, 6, 9 or 12 hours.

• Press the

“Start (Pause)”

button.

The indication over to the “Start Delay” button lights

up and goes off when the programme starts.

• Once having pressed the

“Start (Pause)”

button, the

countdown of the time delay begins. When the

programme starts, the start delay indicator light goes off

and is replaced by the programme sequence indication.

•After the

“Start (Pause)”

button has been pressed,

the number of hours preselected can be reduced by

pressing again the “Start Delay” button.

To cancel the “Start Delay”

..before you press the “Start (Pause)” button:

• Turn the programme selector to another position or

press the

“Reset”

button.

..after having pressed the “Start (Pause)” button:

• Press the

“Reset”

button for at least 3 seconds - the

start delay indicator light goes out.

Open the tap and press the

“Start (Pause)”

button. The

indication lamp next to the

“Start (Pause)”

button lights

up. The programme sequence indicator shows the current

programme phase, running from left to right through

Wash, Rinse, Spin/Drain.

When the programme phase is finished, the corresponding

indication goes out.

Before starting and after end of a programme, the lamp

lights to show that the door can be opened. As long as a

wash programme is running, the door remains locked and

must on no account be forced open. In case you have an

urgent need to open it during a running programme, refer

to “Cancel (Reset) a running programme before the end”.

“Service”

Lighting up of the “Service” indication can be caused by a

fault in an electrical component. Refer to the

“Troubleshooting Guide” in your Instructions for Use; if

the fault persists, contact our After Sales Service.

“Water tap closed”

The appliance has no or insufficient water supply. Open

the water tap; if the indication still lights up, refer to the

“Troubleshooting Guide” in the Instructions for Use.

“Clean pump”

Waste water is not pumped out. Check whether the drain

hose is kinked or the filter must be cleaned; in the latter case

refer to the Instructions for Use (“Removing the Filter”).

• All the lights of the programme sequence indicator

are off, and the “Door open” indication lights up.

1. Turn the programme selector to the “Off/O” position.

2. Close the water tap.

3. Open the door and unload the machine.

4. Leave the door ajar to allow the drum to dry.

1. Press the

“Start (Pause)”

button to pause the

programme. The light flashes.

2. Select the new programme (with temperature), any

options and another spin speed if you want.

3. Press the

“Start (Pause)”

button again. The new

programme continues at the same position where the

previous programme was interrupted. Do not add

detergent for this programme.

The

“Reset”

button cancels a programme before the end.

• Press the

“Reset”

button for at least 3 seconds. Any

existing water is drained out before the door can be

opened.

START DELAY

PROGRAMME START

“DOOR OPEN” INDICATION

RED INDICATIONS

PROGRAMME END

CHANGE PROGRAMME AND/OR OPTIONS

AFTER PROGRAMME START

CANCEL (RESET) A RUNNING

PROGRAMME BEFORE THE END

30106243GB.fm Page 2 Monday, January 5, 2009 12:00 PM

Black process 45.0° 150.0 LPI

Whirlpool awo 447 Seite 2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Missbrauch melden von Frage und/oder Antwort

Art des Missbrauchs:

Forenregeln

Neu registrieren

Andere Handbücher von Whirlpool awo 447

Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Ihre Frage wurde zu diesem Forum hinzugefügt

Info