5019 301 06373
Whirlpool is a registered trademark of Whirlpool USA
Add detergent as indicated on the front page and as described in
the chapter “Detergent and Additives” in your Instructions for Use.
1. Turn the
programme selector
to the desired programme.
The display shows the programme duration in hours and
minutes as well as the predefined temperature. The
“Start
(Pause)”
button blinks.
2. The
temperature
can be altered by pressing the
“Temperature” button.
3. The indication lamp of the predefined
spin speed
lights up; in
case you want to set another spin speed
Push the button of any option desired - the respective indication lights up.
When the combination of programme and additional option(s) is
not possible, the indication lights switch o
Unsuitable combinations of options are deselected automatically.
“Clean+” button
• C
(powder
efficiency to get better wash performance and stain removal.
• C
• Add an appropriate amount of in-wash additive for stain
removal (powder) to the main wash chamber
your detergent (only use powder detergent with this option).
Respect the manufacturer’s dosing instructions.
• Prolongs the programme by approx. 10 to 15 minutes.
• Appropriate for use of stain removers and bleaches on oxygen
basis.
Chlorine or perborat
“Prewas
• Only for or example sand, granular dirt)
sensible. Increases the cycle time by approximately 15 min.
• Do not use liquid detergent for the main wash when
the Prewash option.
“Easy ironing” button
• Can be used together with “Cotton
load” programmes to make ironing easier
• I
“Intensive rinse” button
• More water is added and
• This option is particularly suitable for areas with very soft
waterhelps people with allergies.
“Rinse hold” button
• The laundry remains in the last rinse water without
progressing to the final spin cycle to avoid creasing and prevent
colours from changing.
• This option is particularly recommended for the programmes
“Synthetics”, “Daily load” and “Del
• It is particularly useful if you want to postpone spinning to a
later time, or if you want to drain only
• If you select “Rinse hold”, do not leave the laundry to soak for
too long.
Note:
The programme stops to “Rinse hold”
“Rinse hold” light in the programme sequence indicato
The indication lamp next to the
“Start (Pause)”
button blinks.
T
• Press the
“Start (P
button; the programme will
terminate automatically with the final spin cycle for the present
wash progra
CONSUMPTION DATA
Pro
Te m e a t r e
(°C)
Load
(kg)
Wa
(l)
Energy
(kWh)
Approx. Programme Duration
(hours : minutes)
*
White Cotton 95 7.0 74
**
2.10 2:10
Coloured Cotton 6 7.0 54
1.19 2:20
Coloured Cotton 4 7.0 69 0.75 2:05
Synthetics 60 3.0 46
**
0.80 1:35
Synthetics 40 3.0 42 0.40 1:20
Daily load 40 4.0 48 0.50 1:00
Quick wash 30 4.0 48 0.25 0:30
Delicates 30 1.5 60 0.50 0:45
Sport 30 3.0 52 0.50 1:34
Lingerie 30 1.0 45 0.45 0:36
W 40 1.0 60 0.55 0:45
Handwash 40 1.0 45 0.55 0:40
Eco Cotton
***
60 7.0 54 0.91 4:00
Consumption values were measured in normalized conditions in compliance with Stane
may vary with respect to the values in the table in relation to the water supply pressure and temperature, the load and the type o
*
The time indicated on the display can deviate fro
conditions applicable at that time.
**
Tut.
***
Reference P
ADD DETERGENTS, CLOSE THE DOOR
AND SELECT THE PROGRAMME
SELECT ANY DESIRED OPTIO
• If you do not wish to spin the clothes, turn the programme
selector knob to the “Drain
“Start
(Pause)”
button.
“Spin” button
• Every programme has a predefined
• Press the button to set another spin speed.
• If spie final spinning is cancelled but
intermediate spin peaks remain during rinse. The water is
drained out only
The “Start delay” allows to run the machine at the consumer’s
convenience, for example at night when electricity is cheaper. Do
not use liquid detergent when activating the “Start delay”.
• Select programme, temperature and options.
• Press the “Start delay” button to select the delay time by 1 to 23 hours.
•P
“Start (P
button.
The indication light next to the “Start delay
and the countdown of the delay time begins. The dot between
hours and minutes of the indicated delay time as well as the
light of the start delay button will keep blinking until the
programme starts.
• The time delay indication disappears when the programme
starts and it is replaced by the remaining programme time.
• Once having pressed the
“Start (P
button, the number
of hours preselected can be reduced by pressing and holding
the “Start delay1 hour on, the delay time can
also be reduced by minutes.
T
...before you press the “Start (Pause)” button:
• Tanother position or press the
“Reset”
button.
...after having
•P
“Start (P
button - the start delay will
disappear from the display
“Start (Pause)”
again to
start the selected programme immediately
Open the tap and press the
“Start (P
button. The
indication lamp next to the
“Start (Pause)”
button lights up. The
programme sequence indicator shows the current programme
phase, running from left to right through Wash, Rinse, Spin/Drain.
The display shows the remaining programme time. Due to
variations in load and temperature of inlet water, the remaining
time is newly calculated in certain programme phases. If this is the
case,
an animation appears on the display
.
Before starting and after end of a programme, the lamp lights to
show that the door can be opened. As long as a wash prog
is running, the door remains locked and must on no account be
forced open. In case you have an urgent need to open it during a
running programme, refer to “Cancel (Reset) a running
programme before the end”.
“Service”
Lighting up of the “Service” indication can be caused by a fault in an
electrical component. Refer to the “Troubleshooting Gui
your Instructions for Use; if the fault persists, contact our After
Sales Service.
“Water tap closed”
The appliance has no or insufficient water supply. Open
tap; if the indication still lights up, refer to the “Troubleshooting
Guide” in the Instructions for Use.
“Clean pump”
Waste water is not pumped out. Check whether the drain hose is
kinked or the filter must be cleaned; in the latter case refer to the
Instructions for Use (“Removing the Filter”).
• All the lights of the programme sequence indicator are off
and the “Door open
1. Turn the programme selector to the “Off/O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
1. Press the
“Start (P
button to pause the programme.
The light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the
“Start (Pause)”
button again. The new
programme continues at the same position where the
previous programme was interrupted. Do not add detergent
for this programme.
The
“Reset”
button cancels a programme before the end.
•P
“Reset
button for at least 3 seconds. Any existing
water is drained out before the door can be opened.
START DELAY
PRO
“DOOR OPEN” INDICATION
RED INDICA
PROGRAMME END
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
RESET A RUNNING PROGRAMME BEFORE
THE END
30106373GB.fm Page 2 Wednesday, April 14, 2010 6:2
Black process 45.0° 150.0 LPI
