628885
2
Zoom out
Zoom in
Vorherige Seite
1/2
Nächste Seite
Programme
Temperature
(°C)
Load
(kg)
Water
(l)
Energy
(kWh)
without “Rapid”
Approx. programme duration
(hours : minutes)
%
without “Rapid” with “Rapid”
Mixed 40 4,0 48 0,50 1:00 - 55
Cotton 95 6,0 60** 1,90 2:30 -
55Cotton 60 6,0 50 0,80 2:20 1:35
Cotton 40 6,0 55 0,85 2:45 1:15
Synthetics 60 3,0 50** 1,00 2:15 0:59
35
Synthetics 40 3,0 46 0,70 2:15 0:59
Delicates 40 1,5 60 0,60 0:50 -
Delicates 30 1,5 60 0,40 0:46 -
Wool/Handwash 40 1,0 47 0,50 0:40 -
Jeans 40 4,0 52 0,50 1:30 1:10
White 40 6,0 59 0,70 2:20 -
Light colours 40 4,0 60 0,45 1:20 -
Dark 40 4,0 40 0,53 1:40 1:15
Speed 15´ 30 3,0 20 0,13 0:15 -
AquaEco 40 3,0 19 0,45 1:00 -
Cotton *
60 6,0 44 0,69 4:00 -
53
Cotton *
60 3,0 34 0,50 2:30 *** -
Cotton *
40 3,0 34 0,45 2:30 *** -
Consumption values were measured in normalized conditions, in compliance with IEC/EN 60456. In the home, they may vary depending on the individual water
supply pressure and temperature, the load and the type of wash. The consumption data indicated are based on an inlet water temperature of approx. 15°C through
the cold fill valve as well as the hot fill valve (if available). If your washing machine has a hot fill valve, connection of this valve to hot water supply will lower the
energy consumption by reduced heating times, depending on the individual hot fill inlet water temperature. Water and energy consumptions refer to the default
setting of the programmes, with temperature and load as indicated in the table; selecting any options or changing the spin speed will also change the consumption
data.
The programme duration may differ from the values indicated above as it depends on the operation conditions applicable at that time (see also
“Troubleshooting Guide” in your Instructions for Use).
Approximate remaining moisture content (%). After programme and spinning with maximum selectable spin speed, in default programme setting.
* Reference programmes for Energy Label. For reasons of energy saving, the real water temperature may deviate from the declared cycle temperature.
** To reduce the water temperature, some cold water is added at the end of the main wash cycle, before the pump drains the water out.
*** Automatic adaptation of programme duration after detection of wash load
ADD DETERGENTS, CLOSE THE DOOR AND
SELECT THE PROGRAMME
Load the laundry, close the door and turn the programme selector
to the desired programme; the Start/Pause indicator blinks.
The temperature and spin speed shown on the display can be
altered by pressing the “Temperature” button or the “Spin” button.
If you do not use the “Dosing Aid”, add detergent now.
Your washing machine is designed to save energy. After the
end of a programme, or when a programme is selected but
not yet started, the washing machine will therefore switch off
automatically after about a quarter of an hour. To switch the
washing machine on again, turn the programme selector to “O”
and afterwards to the desired programme again.
SELECT ANY DESIRED OPTION
When the combination of programme and additional option(s) is
not possible, the indication switch off automatically. Unsuitable
combinations of options are deselected automatically.
“Colours 15°” button
Saves energy used for water heating while maintaining a good
wash result.
Supports colour maintenance when washing coloured laundry.
Recommendable for lightly soiled laundry without stains.
Make sure that your detergent is suitable for cold wash
temperatures (15 or 20°C).
Not selectable for Cotton 70 - 95°C.
“Intensive rinse” button
More water is added and rinse cycle is prolonged.
This option is particularly suitable for areas with very soft
water, washing baby linen and helps people with allergies.
“Rapid” button
Enables quicker washing by shortening the programme
duration.
Recommendable for only lightly soiled laundry.
Not selectable for Cotton 70 - 95°C.
“Prewash” button
Adds a prewash cycle to the wash programme selected;
prolongs the programme by about a quarter of an hour.
Recommended for heavily soiled laundry (e.g. with sand or
granular dirt).
Do not use liquid detergent for the main wash when activating
the “Prewash” option.
“Soil level” button
Adapts the programme duration to the soil level of
your laundry. Also influences the detergent quantity
recommendation when using the “Dosing Aid” button.
= lightly soiled - = normally soiled - = heavily soiled
Not all soil levels are selectable for each programme.
“Spin” button (incl. “Rinse hold”)
Every programme has a predefined spin speed.
Press the button to set another spin speed.
If you select spin speed “0”, the final spinning is cancelled
and the water is drained out only. However, intermediate spin
phases remain during the rinse.
If you select “Rinse hold”, the laundry remains in the last
rinse water without progressing to the final spin cycle, to
avoid creasing and prevent colours from changing. To activate
the “Rinse hold”, press the “Spin” button repeatedly until the
“Rinse hold” symbol on the display lights up.
The wash programme stops to “Rinse hold” when the “Rinse
hold” symbol on the display blinks; the light of Start/Pause
button also blinks.
- To terminate the „Rinse hold“ by spinning the laundry, press
Start/Pause - the laundry will be spun with the default
spin speed. You can also select another spin speed with the
„Spin“ button before you start the spin cycle by pressing
Start/Pause”.
- To terminate the „Rinse hold“ by draining the water without
- the sensor technology adapts water, energy and programme duration to the size of your wash load.
PROGRAMME START
Open the tap and press the “Start/Pause button . The indicator
next to the Start/Pause button lights up.
CHILD LOCK
Activating the child lock prevents children from starting a wash
cycle or changing the settings of a running programme. The child
lock cannot be activated or deactivated when the programme
selector is in the “O” position. To activate the child lock:
Turn the programme selector to a programme position, or run
a programme as usual.
Press the 2 buttons marked with the key symbol
simultaneously for at least 3 seconds. A key-like symbol will
shortly appear on the display to indicate that the child lock is
active.
Any time you try to change a programme setting with active
child lock, the display will briefly show the key-like symbol. The
programme setting cannot be changed anymore. The only change
possible is to switch the washer off by turning the programme
selector to the “O” position.
To deactivate the child lock:
Press again the 2 buttons marked with the key symbol simul-
taneously for at least 3 seconds.
FAILURE INDICATION
In case of any failures or irregularities, consult the
“Troubleshooting Guide” in your Instructions for Use.
Water tap closed”: no or not sufficient inlet water.
Service”: failure or malfunction of an electrical component.
Clean pump”: waste water is not pumped out.
Spin speed on display blinks: unbalance during spinning.
PROGRAMME END
The “Door open” indicator lights up, and the display shows “End”.
After about a quarter of an hour, the washing machine will switch
off completely to save energy.
1. Turn the programme selector to the “O” position.
2. Close the water tap.
3. Open the door and unload the machine.
4. Leave the door ajar to allow the drum to dry.
DETERGENT OVERDOSAGE INDICATION
The symbol will light up at the end of the programme if you used
too much detergent. Use less detergent next time. If the symbol
lights up and the display shows “Fod”, too much foam interrupted
the wash process; refer to the “Troubleshooting Guide” in your
Instructions for Use.
1.
CHANGE PROGRAMME AND/OR OPTIONS
AFTER PROGRAMME START
Press the “Start/Pause button to pause the programme. The
light blinks.
2. Select the new programme, temperature, any options and
another spin speed if you want.
3. Press the “Start/Pause button again. The new programme
continues at the same position where the previous programme
was interrupted. Do not add detergent for this programme.
CANCEL (RESET) A RUNNING PROGRAMME
BEFORE THE END
The “Reset/Drain button cancels a programme before the end.
Press and hold the “Reset/Drain button for a few seconds; an
animation appears on the display. The water is drained out; it
may last some time until you can open the door.
CONSUMPTION DATA
Power consumption in off-mode 0,16 W / in left-on mode 0,16 W
spinning, press the „Spin“ button until spin speed „0“ appears
on the display; then press “Start/Pause to start the draining.
- Do not leave the laundry to soak for too long in the “Rinse
hold” (especially silk).
SET CYCLE END
With this function you can postpone your programme to complete
at a later time: press the button to select in how many hours
the programme shall be finished. Thus, it allows you to have
your laundry ready at a particular time and to profit from more
favorable energy rates during the night, for example. Do not use
liquid detergent when activating “Cycle end” option.
The time until the “Cycle end” can be selected in full hour time
segments (1 to 24 h). When you press the button, the shortest
possible time will be displayed; keep on pressing the button to
loop through all the available times. To remove it again, keep
on pressing the button until you see the value “0:00”.
When you have selected the desired time until the “Cycle
end”, press “Start/Pause - the countdown will begin.
During the countdown, you can still modify the programme
setting (select or deselect options, change spin speed etc.).
If the modifications prolong the programme duration so that
it overruns the originally set time until the “Cycle end”, the
programme will start immediately.
Sometimes the programme may finish before the selected
time until the “Cycle end” has expired (e.g. for small loads).
In this case, the washing machine will tumble the laundry
regularly to keep it fresh, until the selected “Cycle end”
time has expired. During tumbling, the display will show an
animation. The tumbling phase can be stopped at any time
either by pressing any button or by rotating the programme
selector; the animation will stop and the door will unlock in
about 1 minute as indicated on the display.
DETERGENT DOSING RECOMMENDATION
With the “Dosing Aid” button, you can make your washing
machine indicate you the recommended detergent quantity for
your wash load, depending on the soil level selected and the size
of the load.
Helps to save detergent and protect the environment and also
sensitive skin by avoiding detergent overdosing.
Before you use this function, you must adapt the washing
machine to the dosing amounts which are recommended
for the detergents you use. Also check if your region’s water
hardness corresponds with the water hardness level “soft” of
your washing machine - if not adapt it.
Select programme, options and cycle end BEFORE using the
“Dosing Aid” button.
For any details, refer to the separate “Dosing Aid” Instructions for
Use.
“DOOR OPEN” INDICATION
Before starting and after end of a programme, the lamp lights to
show the the door can be opened. As long as a wash programme
is running, the door remains locked and must on no account be
forced open. In case you have an urgent need to open it during a
running programme, refer to “Reset” a running programme before
the end”.
ECO MONITOR
The „Eco monitor“ gives you a rough feedback about the power
consumption of the programme setting you selected. As soon as
you turn the programme selector to any programme, the „Eco
monitor“ is on.
The indicator on the left is to show that the „Eco monitor“
is active. The four indicators next to it show the degree of
consumption: the less power your programme setting is
forecasted to consume, the less indicators will light up. This
depends on the programme, temperature and options selected,
and also on the size of the wash load. For that reason, the
forecasted degree of power consumption may adapt when the
washing machine detects the wash load.
2

Brauchen Sie Hilfe? Stellen Sie Ihre Frage.

Forenregeln

Missbrauch melden von Frage und/oder Antwort

Libble nimmt den Missbrauch seiner Dienste sehr ernst. Wir setzen uns dafür ein, derartige Missbrauchsfälle gemäß den Gesetzen Ihres Heimatlandes zu behandeln. Wenn Sie eine Meldung übermitteln, überprüfen wir Ihre Informationen und ergreifen entsprechende Maßnahmen. Wir melden uns nur dann wieder bei Ihnen, wenn wir weitere Einzelheiten wissen müssen oder weitere Informationen für Sie haben.

Art des Missbrauchs:

Zum Beispiel antisemitische Inhalte, rassistische Inhalte oder Material, das zu einer Gewalttat führen könnte.

Beispielsweise eine Kreditkartennummer, persönliche Identifikationsnummer oder unveröffentlichte Privatadresse. Beachten Sie, dass E-Mail-Adressen und der vollständige Name nicht als private Informationen angesehen werden.

Forenregeln

Um zu sinnvolle Fragen zu kommen halten Sie sich bitte an folgende Spielregeln:

Neu registrieren

Registrieren auf E - Mails für Whirlpool AWO-C 6350 wenn:


Sie erhalten eine E-Mail, um sich für eine oder beide Optionen anzumelden.


Andere Handbücher von Whirlpool AWO-C 6350

Whirlpool AWO-C 6350 Kurzanleitung - Deutsch - 2 seiten

Whirlpool AWO-C 6350 Bedienungsanleitung - Deutsch - 12 seiten

Whirlpool AWO-C 6350 Bedienungsanleitung - Englisch - 12 seiten

Whirlpool AWO-C 6350 Bedienungsanleitung - Holländisch - 12 seiten

Whirlpool AWO-C 6350 Kurzanleitung - Holländisch - 2 seiten

Whirlpool AWO-C 6350 Bedienungsanleitung - Französisch - 12 seiten

Whirlpool AWO-C 6350 Kurzanleitung - Französisch - 2 seiten


Das Handbuch wird per E-Mail gesendet. Überprüfen Sie ihre E-Mail.

Wenn Sie innerhalb von 15 Minuten keine E-Mail mit dem Handbuch erhalten haben, kann es sein, dass Sie eine falsche E-Mail-Adresse eingegeben haben oder dass Ihr ISP eine maximale Größe eingestellt hat, um E-Mails zu erhalten, die kleiner als die Größe des Handbuchs sind.

Ihre Frage wurde zu diesem Forum hinzugefügt

Möchten Sie eine E-Mail erhalten, wenn neue Antworten und Fragen veröffentlicht werden? Geben Sie bitte Ihre Email-Adresse ein.



Info